Platinum 4000 H Installation and User Manual

Installation and user guide

Inverter

2100 H, 3000 H, 4000 H, 4600 H

As at 09/2012, Material no. 753 840-AB

EN

2

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

3

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Contents

1 Introduction 5

1.1 PLATINUM H 5

1.2 About this manual 5

1.3 Symbols used 5

1.4 Symbols on product and packaging 6

2 Safety 7

2.1 Intended usage 7

2.2 Improper usage 7

2.3 Personnel requirements 7

2.4 General safety instructions 7

3 Installation 8

3.1 Scope of delivery 8

3.2 Unpacking 8

3.3 Assembly 9

3.4 Connection 12

4 Placing into operation 23

4.1 Switching on 23

4.2 Navigation in the Installation Menu 23

4.3 Installation Menu 25

4.4 Commissioning after replacement of a device 32

5 Operation of the inverter 33

5.1 Control elements and displays 33

5.2 Operation display 34

5.3 Isolation from the generator ﬁeld 37

Contents

4

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

6 Menu on the inverter 38

6.1 Menu operation 38

6.2 Menu tree 39

6.3 Status menu 40

6.4 Setup menu 43

6.5 Commands menu 51

6.6 Alarm Setup menu 53

6.7 Event Log menu 56

6.8 Statistics menu 57

7 Web server 58

7.1 Connection between inverter and computer 58

7.2 Starting the web server 61

7.3 Menu tree 62

7.4 Home 63

7.5 Statistics 66

7.6 Setup 67

7.7 Event Log 75

7.8 Status 76

7.9 Help 78

7.10 Logout 78

8 Maintenance and cleaning 79

8.1 Maintenance 79

8.2 Cleaning 79

9 Faults and troubleshooting 80

9.1 Checklist in the event of faults 80

9.2 Event list 80

9.3 Faults and troubleshooting 85

10 Technical data 86

11 Taking out of operation 88

12 Disposal 89

Contents

5

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Introduction

1 Introduction

1.1 PLATINUM H

Inverters in the PLATINUM H series are single-phase feed-in inverters for different

power ranges; see “Technical data” on page 86.

Inverters in the PLATINUM H series are equipped with an integrated web server, which

allows data to be viewed and evaluated via a network or via the internet.

Up to 30 PLATINUM H inverters can be connected to form a single inverter system via

the CAN network.

1.2 About this manual

This installation and operating manual describes the installation and operation of the

PLATINUM inverters of the types 2100 H, 3000 H, 4000 H, 4600 H.

Additional documents

The following additional documents are available in the download area of our website

www.platinum-nes.com:

▪ Detailed installation and user guide

▪ Information on fault current protection devices

▪ Detailed list of events for detecting/eliminating faults

▪ Overview of country and grid codes

▪ Declaration of conformity and certiﬁcates

▪ Manufacturer’s warranty

1.3 Symbols used

1.3.1 Notes

Notes give tips on how to work easily and safely or contain further

information.

1.3.2 Structure of warnings

WARNING WORD

Type, source and consequence of the hazard!

f Measures to avoid the hazard.

6

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Introduction

1.3.3 Hazard levels in warnings

Symbol Warning

word

Probability of occurrence Consequences of

non-observance

DANGER

Imminent danger Death, serious injury

WARNING

Potential danger

Death, serious injury

CAUTION Potential danger Minor injury

– CAUTION Potential danger Damage to property

1.4 Symbols on product and packaging

The following symbols are used on the type plate on the bottom right-hand side of the

inverter:

Symbol Meaning

High voltage

Risk of electric shock

Discharge time: 60 minutes

High voltages may still be present in the interior of the

inverter up to 1 hour after it is switched off.

Hot surface

The cooling element on the rear of the inverter can get very

hot and reach temperatures of up to 90°C.

Read the manual

Read this manual before carrying out any work on the in-

verter.

Disposal

▪ Do not dispose of PLATINUM inverters in household

waste.

▪ Packaging and replaced parts are to be disposed of in

accordance with the regulations of the country in which the

inverter was installed.

7

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Safety

2 Safety

2.1 Intended usage

▪ Inverters are to be used solely for the purpose of feeding photovoltaically generated

solar energy into the public grid.

▪ All other usage does not comply with the regulations.

2.2 Improper usage

▪ The inverters are not to be used in island grids.

▪ The inverters are not to be used in vehicles.

▪ The inverters are not to be used in areas at risk of explosion (ﬂour dust, sawdust,

etc.).

▪ The inverters are not to be exposed to direct sunlight.

▪ The inverters are not to be used in areas in which the ammonia content of the air

exceeds 20 ppm.

▪ All warranty claims will be rendered null and void in the event of failure to comply

with the warranty terms or the information provided in this operating and installation

manual.

2.3 Personnel requirements

The inverter may only be installed and put into operation in accordance with this

installation and user guide by trained specialist personnel, for example:

▪ Service partners who are authorised by PLATINUM

▪ Authorised specialist personnel with knowledge of the applicable guidelines and

standards

2.4 General safety instructions

▪ The inverters are to be used in their original state without independent modiﬁcations

and in a technically perfect condition.

▪ Steps must be taken to ensure that the following are adhered to when assembling

and connecting the inverter and the PV system:

– Guidelines and regulations valid in the respective country

– Provisions of the trade associations, TÜV, VDE (Association for Electrical, Electronic

& Information Technologies)

– Technical connection conditions of the energy supplier responsible

– National and international regulations and provisions

▪ Ensure that all protection devices are working correctly.

▪ Observe the operating conditions - refer to “Technical data” on page 86.

8

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

3 Installation

3.1 Scope of delivery

▪ Inverter

▪ Wall bracket

▪ Brief guide

▪ Installation materials

▪ Grounding kit

3.2 Unpacking

CAUTION

Risk of injury!

f Wear safety shoes when unpacking the inverter and during

installation.

f Ensure that the inverter is positioned securely.

1

1. Place the box the correct way up on

the ﬂoor (note the lettering).

2. Cut through the seal and open the box

on the top side.

3. Take out the wall bracket from the

packaging.

4. Take off the upper padding elements.

5. Raise the inverter by its underside and

lift it by the handles (1) out of the box.

6. Remove the lower padding element.

7. Take out the installation materials and

the grounding kit.

8. Take out the brief guide.

Enclosed installation materials

▪ Seals for the AC connection

▪ Jumpers for grounding and network termination

▪ Fastening and locking clamp for anti-theft protection

9

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

3.3 Assembly

3.3.1 Safety instructions

WARNING

Injury may result if the inverter falls!

f Use ﬁxing materials suited to the assembly wall and the weight of the

inverter.

f Wear safety shoes during assembly and disassembly.

f Ensure that the inverter is positioned securely.

CAUTION

Damage to the inverter due to excessive buildup of dust.

f Avoid excessive build-up of dust.

f Avoid build-up of dust with electrically conductive dust particles.

In order to comply with the requirements of standard IEC-62109, a

possibility must be provided for tool-free isolation of the solar generator.

If the design does not feature an integrated DC isolator, an external

isolation device is mandatory; this must be easily accessible.

PLATINUM recommends that the inverter should not be installed in living

quarters.

10

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

3.3.2 Mounting the inverter

2

4

150 150

400300

Dimensions in mm

1. Choose a suitable location for mount-

ing. When doing so, note the follow-

ing:

– Mount the inverter in a suspended,

vibration-free position.

– The wall chosen for mounting must

be suitable for the weight and

temperature (90°C).

– Make sure the correct dimensions

and distances are maintained.

– The display should be at eye level

(approx. 1.60 m off the ﬂoor).

– The inverter must be easily ac-

cessible without additional tools or

equipment.

2. Fix the wall bracket to the assembly

wall with suitable ﬁxing materials.

2 3

54

3. Lift the inverter and insert the upper

mountings (2) in the upper slots (3) on

the wall bracket.

4. Align the lower mountings (4) on the

lower slots (5).

11

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

5. Slide the inverter onto the bracket.

Anti-theft protection

6

Two clamps are included in the scope of

delivery, with the aid of which the inverter

can be protected against theft.

A padlock is not included in the scope of

delivery.

1. Mount the fastening clamp (6) with

two screws on the underside of the

inverter.

7

2. Guide the locking clamp (7) through

the fastening clamp.

3. Insert the padlock through the eyelet

on the locking clamp and lock.

12

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

3.4 Connection

3.4.1 Preparatory work

1. If present, disconnect the DC voltage

side with the external disconnect

device from the solar generator.

2. If present, move the switch knob of

the DC isolator on the underside of

the device to the 0 position.

8

Take off the lower cover

t Remove the four screws (8) from the

lower cover and take off the cover.

For safety reasons, it is ESSENTIAL that the following sequence is AL-

WAYS followed when the connections are established:

1. Connect the network.

2. Connect the AC voltage.

3. Conﬁgure the grounding of the PV modules.

4. Mount the lower cover.

5. Connect the DC voltage.

13

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

3.4.2 Network connection

The inverter is equipped with two different network connections:

CAN

Ethernet

▪ CAN: for communication between

multiple inverters

▪ Ethernet: for communication between

the integrated web server of the

master and a computer or the internet

Up to 30 PLATINUM H inverters can be connected into a network with

an overall length of up to 100 m.

Network cable

▪ CAN: cross-section 0.21 mm

2

, max. 100 m

▪ Ethernet: CAT 5 shielded twisted-pair cable with pre-assembled RJ45 plugs

Connect

+POS

10

1. Unscrew the network screw

connection (10) from the left-hand

underside of the inverter.

2. Take out the three-way screwed cable

connection insert.

14

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

11

3. If required, cut open the cable insert

(11) to a width of around 1 mm for the

Ethernet cable.

12

4. Insert the Ethernet cable (12) in the

cable insert.

13

5. Route the CAN cable (13) through the

bore(s) in the cable grommet.

6. Feed all network cables into the hous-

ing from below.

15

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

7. Tighten the network screw connec-

tions.

14

CAN

H

L

COMGND

H

L

COMGND

15

8. Connect the CAN cable to the

terminal block (14). When doing this,

make sure that the lines L and H are

not accidentally swapped over during

connection.

– Incoming line: left-hand terminals L

and H

– Outgoing line: right-hand terminals

L and H

9. At the master inverter, connect the

plug of the Ethernet cable with the lug

facing towards the rear into the socket

(15).

Termination

Termination via an internal terminating resistor ensures correct operation of the

network. This is done by means of a jumper, which lies across the CAN terminal block

and short-circuits two pins.

No jumper is ﬁtted at the factory, so the terminating resistance is not activated.

The terminating jumper is included with the supplied installation materials.

Inverters in the network Jumper position Meaning

Individual (standalone)

inverter

Jumper inserted Terminating resistance activated

First/last inverter in the

network

Jumper inserted Terminating resistance activated

All other inverters in the

network

No jumper

Terminating resistance de-

activated

16

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

16

1. At each inverter, check that the jumper

(16) is in the correct position (in ac-

cordance with the table above).

2. If not, correct the jumper position

accordingly.

3.4.3 Connect the AC voltage

DANGER

Risk of death due to high AC voltage!

f Switch off the mains voltage supply (AC side) before connecting the

inverter (safety device).

f Make sure that the central isolation device can be accessed freely.

f Only connect the inverter to TN or TT networks (see IEC 60364-1)

with 230 V.

f Observe max. fuse protection permitted on the AC voltage side; see

“Technical data” on page 86.

f Establish the AC voltage connection with a circuit breaker.

PLATINUM recommends a type C miniature circuit breaker.

f If an external residual current protective device is required, PLATINUM

recommends using a residual current protective device (RCD) of

type A.

CAUTION

Destruction of the inverter!

f Never connect inverters between two phases.

f Never mix up the phases with PE or N.

f If several inverters are connected, distribute them across the three phases so

that the differences in feed-in power between the phases do not exceed the

maximum permitted unbalanced load of the grid operator.

17

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

Prepare the connection cable for the AC voltage

Dimensioning the wire cross-section is the responsibility of the

electrician and depends on the cable length and installation situation.

▪ Min. cross-section 6 mm

2

▪ Max. cross-section 16 mm

2

1. Protect the AC voltage connection lines with appropriate fuses; see “Technical data”

on page 86.

2. Strip 18 mm of insulation from the AC voltage connection lines and add wire-end

sleeves.

Connect

The AC connection screw ﬁtting does not have a seal. One of the sup-

plied seals must be used to ensure that the requirements for safety class

IP65 are met.

9

1. Unscrew the AC screw connection (9)

from the right-hand underside of the

inverter.

2. Route the prepared AC voltage

connection line through the AC screw

connection. Use a seal if required.

3. Feed the AC voltage connection line

into the housing from below.

4. Tighten the AC screw connection.

18

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

5. Connect the AC voltage connection

cable to the inverter:

Terminal Assignment

GND Protective ground conductor

N Neutral conductor

L Feed-in phase

6. Tighten the terminals with a tightening

torque of 1.5 Nm.

3.4.4 Conﬁguration of the grounding of the PV modules

The inverter meets all requirements in terms of technical safety.

Depending on the grounding of the connected PV modules, the following work may

need to be carried out on the inverter:

Grounding of the

PV modules

Inverter setup

Not grounded Factory setup

No further grounding measures required

Negative grounding ▪ Install grounding strap

▪ Connect grounding jumper

Positive grounding ▪ Install grounding strap

▪ Connect grounding jumper

▪ Swap internal cables

Install grounding strap

WARNING

Risk of electric shock and damage to the inverter.

f Only install the grounding strap on grounded PV modules.

The grounding strap is included in the enclosed grounding kit.

19

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

2 -NEG

GND/PE

Ungrounded

Terminal

Grounded

Terminal

12

17

N5

t Connect the grounding strap between

the DC grounding terminal (17) and

N5.

Connect grounding jumper

WARNING

Risk of electric shock and damage to the inverter.

f Only install the grounding jumper on grounded PV modules.

The grounding jumper is included in the enclosed grounding kit.

2 -NEG

GND/PE

Ungrounded

Terminal

Grounded

Terminal

12

18

t Plug in the grounding jumper at the

connector (18) (according to the

grounding of the PV modules):

– Not grounded No jumper

– Positive grounding Pin 1 and pin 2

– Negative grounding Pin 2 and pin 3

20

Installation and user guide for PLATINUM inverters 2100 H, 3000 H, 4000 H, 4600 H

Installation

Swap over the internal cables if the PV modules are positively grounded

WARNING

Risk of electric shock and damage to the inverter.

f Only swap over the internal cables if the PV modules are positively

grounded.

At the factory, black cables are assigned to the connections N1 to N4 and red cables to

the connections P1 to P4. In the case of negatively earthed PV modules, this assign-

ment needs to be swapped over.

N4

N3

N2

N1

P4

P3

P2

P1

Ungrounded

Terminal

Grounded

Terminal

12

t Swap over the cables at the following

connections (swap red and black):

– N1 and P1

– N2 and P2

– N3 and P3

– N4 and P4

This concludes the work inside the inverter. The lower cover can be closed again.

8

t Attach the lower cover with the four

screws (8).

Page is loading ...

Platinum 4000 H Installation and User Manual

This manual is also suitable for

Platinum 4000 H Installation and User Manual

Related papers

Other documents