Platinum 13000 TL Installation guide

EN

Stand 04/2011, Mat. No. 749 442-AA

Installation and Operating Manual

Inverter

13000 TL, 16000 TL, 19000 TL, 22001 TL, 22000 TL

PLATINUM Inverter TL

2

Installation and Operating Manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 442-AA

Thank you for buying a PLATINUM inverter 13000 TL, 16000 TL,

19000 TL, 22000 TL, 22001 TL.

In this instruction, we have compiled all information that is important

for installation and operation.

If you still have any trouble, please call our service hotline.

Service hotline

You can reach the PLATINUM service hotline as follows:

Phone +49 7522 73 777

Fax +49 7522 73 737

E-Mail service.platinum@diehl-controls.com

You can find more service documents at

www.diehl.com/photovoltaics.

3

PLATINUM Inverter TL

Installation and operating manual: PLATINUM Inverter TL

Version 04/2011

Mat. No. 749 442-AA

Menu structure

The service menu is exclusively relevant for service purposes; it is

not accessible directly from the menu.

For access to service menu see 8.1 Service Menu.

Main Menu

Operation display . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 49

Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 50

Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 54

Time settings . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 54

Service Menu . . . . . . . . . . . . . . . . . . .

see p. 70

Event list . . . . . . . . . . . . . . . . . . . . . .

see p. 71

Parameters. . . . . . . . . . . . . . . . . . . . .

see p. 71

PhaseBalancer . . . . . . . . . . . . . . . . . .

see p. 72

Reconfiguration . . . . . . . . . . . . . . . . .

see p. 76

Grid support . . . . . . . . . . . . . . . . . . . .

see p. 76

MPP mode . . . . . . . . . . . . . . . . . . . . .

see p. 78

Startup. . . . . . . . . . . . . . . . . . . . . . . .

see p. 78

Meter . . . . . . . . . . . . . . . . . . . . . . . . .

see p. 79

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 57

Alarm volume . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 58

Alarm contact . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 58

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 59

Feed payback . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 60

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 60

Energy meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 61

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 62

Operating data . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 62

System data . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 63

Inverter type . . . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 64

Inverter version . . . . . . . . . . . . . . . . . . . . . . . . . . see p. 65

5

Installation and operating manual: PLATINUM Inverter TL

Version 04/2011

Mat. No. 749 442-AA

PLATINUM Inverter TL

1 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

1.1 Warning notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

1.2 Other symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3 Symbols on the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2 Safety and Dangers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.1 Variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.1 Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

5.2 Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

5.3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.4 Mounting the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

5.5 Connection of the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

6 Start Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

6.1 Initial startup of inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6.2 Phase Balancer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

6.3 Exchanging inverters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

7.1 DC disconnector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

7.2 Display and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

7.3 Standard screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

7.4 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

7.5 Operation Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

7.6 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

7.7 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

7.8 Error display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

8 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

8.1 Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

9.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

PLATINUM Inverter TL

6

Installation and operating manual: PLATINUM Inverter TL

Version 04/2011

Mat. No. 749 442-AA

10 Placing out of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

10.1 Dismounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

11 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

12 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

12.1 Table of events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

13 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

14 EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

15 Manufacturers' Warranty of Diehl AKO Stiftung & Co. KG . . . . . . . . . . . . . . . . . . . . . . . . . 94

7

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Symbols

1Symbols

1.1 Warning notices

Classification of warning notices

The warning notices differentiate between three types of dangers

indicated by the following signal words:

Î Caution warns of material damages.

Î Warning warns of bodily injuries.

Î Danger warns of a danger to life.

Layout of the warning notices

1.2 Other symbols

Instructions

Layout of instructions:

Â Instruction to do something.

Result of the action, if necessary.

Lists

Layout of bulleted lists:

Î List level 1

t List level 2

Layout of numbered lists:

1. List level 1

2. List level 1

2.1 List level 2

2.2 List level 2

Signal words

Type and source of the danger!

Â Measure to avoid the danger.

PLATINUM Inverter TL

Symbols

8

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

1.3 Symbols on the product

9

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Safety and Dangers

2 Safety and Dangers

Â Use inverters according to their intended use.

Â Use inverters in original and technically fully intact condition

without unauthorized modifications.

Â Ensure that inverters are installed and serviced by qualified

specialists only.

Â Ensure that exclusively qualified electrician carry out the

assembly and installation work described in this installation and

operating manual.

Â Prior to installation and maintenance work, make certain that the

inverter is de-energized.

Â Ensure that the following is observed when mounting and

connecting the inverter and the PV plant:

t directives and rules applicable in the respective country

t regulations stipulated by trade associations and inspection

authorities and agencies

t technical connection conditions (TAB) of the relevant energy

supplier

t national and international rules and regulations

Â Always mount inverters in a vertical position.

Â Protect inverters from direct sunlight.

Â Verify that ventilation openings are not blocked or covered.

Â Ensure that all protection devices are fully operational.

Â Observe conditions of use (see 13 Technical Data).

3 Intended Use

Â Use the inverter exclusively to feed photovoltaically converted

solar energy into the public 230 V/50 Hz mains.

Â Do not use the inverter in autonomous power systems.

Â Do not use the inverter in vehicles.

Â Do not use inverters in explosive atmospheres (flour dust,

sawdust etc.

Â Do not use inverters in atmospheres where the ammonia

concentration of the air exceeds 20 ppm.

Â Observe warranty conditions.

Note

If these warranty conditions and the information contained in this

installation and operating manual are not observed, all warranty

claims will expire.

PLATINUM Inverter TL

Function

10

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

4Function

4.1 Variations

The PLATINUM line includes the following variants with different

power ranges (see 13 Technical Data):

Î PLATINUM 13000 TL

Î PLATINUM 16000 TL

Î PLATINUM 19000 TL

Î PLATINUM 22000 TL

Î PLATINUM 22001 TL

Possible types:

Î wall-mounted device

Î free-standing device

Î free-standing device, outside

Î with DC disconnector

Î without DC disconnector

Note

The standard IEC-62109 requires the possibility of separating from the

PV generator without any tools. For models without integrated DC

disconnector, an external disconnector on the generator side is

required.

4.2 Options

Upgrades for an inverter or an inverter system:

Î Inverter networking via PLATINUM network (EIA 485 bus)

Î Optical and acoustical indicator devices.

Î Remote monitoring or remote readout with PLATINUM

WebMaster

Î Central display of systems with PLATINUM ViewMaster

Î Evaluation of system data with PLATINUM PV-Monitor

Î Remote control of AC power in connection with PLATINUM

PowerCommander, PLATINUM WebMaster and a control device

on the mains supply side.

11

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Assembly

5 Assembly

5.1 Scope of delivery

Wall-mounted device:

Î PLATINUM inverter with protector

Î Mounting fixture

Î Brief instruction

Free-standing device:

Î PLATINUM inverter preassembled in Power Block protective

housing TL Large

Î Power Block protective housing

Î Protector

Î Brief instruction

Free-standing device, outside:

Î PLATINUM inverter with protector preassembled in Power Block

protective housing with protective cover and protective grate

Î Brief instruction

Note

A detailed installation and operating manual is available in the

download area of our website www.diehl.com/photovoltaics.

PLATINUM Inverter TL

Assembly

12

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

5.2 Transport

Transport with lifting gear

Â Load thread on inverter exclusively in longitudinal direction.

Â Ensure that carrying straps or ropes are at least 2 m long.

- or -

Â Use yoke.

Fig. 1 Transport with lifting gear

(1) Threaded holes for transport eyebolts

(2) Recessed grip

Â Screw DIN 580 M10 eyebolts into threaded holes 1 on inverter.

Â Fasten lifting gear on eyebolts.

Note

Eyebolts are not included in delivery.

Danger

Danger to life due to inverter dropping from the wall!

Â Transport packaged inverter exclusively with a forklift

truck and on a transport pallet.

Â Do not tilt inverter.

Â Transport inverter exclusively with lifting gear.

1

2

13

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Assembly

5.3 Unpacking

Unpacking the wall-mounted device

Fig. 2 Unpacking the wall-mounted device

(1) Upper part of packaging

(2) Wooden protection elements

(3) Bottom part of packaging

(4) Transport pallet

Â Put transport pallet 4 with inverter on even ground.

Â Remove upper part of packaging 1.

Â Lift inverter out of bottom part of packaging 3.

Use wooden protection elements 2 for carrying.

Â Take inverter to installation site.

On installation site:

Â Unscrew wooden protection elements 2 from inverter.

1

2

3

4

PLATINUM Inverter TL

Assembly

14

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

Unpacking the free-standing device

Fig. 3 Unpacking the free-standing device

(1) Transport pallet

Â Take inverter to installation site on transport pallet 1.

Â Put transport pallet with inverter on even ground.

Â Remove plastic protective packaging.

Â Put inverter on intended installation site.

1

15

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Assembly

5.4 Mounting the inverter

Danger

Danger to life due to electric shock!

Â Have the inverter opened exclusively by the

PLATINUM service or service partners authorized by

DIEHL Controls.

Danger

Danger to life due to incorrect connection of inverter!

Â Have inverters installed by qualified specialists

exclusively.

The qualified specialist personnel requires a license

from the relevant energy suppliers.

Danger

Risk of explosion due to unsuitable installation site!

Â Do not install inverters in explosive atmospheres (flour

dust, sawdust etc.).

Â Ensure that the ammonia concentration in the air is

20 ppm at most.

Danger

Danger to life due to inverter dropping from the wall!

Â Use mounting elements appropriate for the mounting

wall and the weight of the inverter unit.

During mounting and dismounting:

Â Wear protective shoes.

Â Ensure a stable position.

Caution

Material damage due to unprotected installation site!

Â Observe admissible ambient temperature.

(see 13 Technical Data).

PLATINUM Inverter TL

Assembly

16

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

Note

DIEHL Controls advises against installing the inverter in living spaces.

Protector

Fig. 4 Removing protector

(1) Protector

For versions with protector, prior to installation of inverter:

Â Hold protector 1 on bottom side and pull away from inverter.

Caution

Material damage due to excessive dust formation!

Â Degree of protection IP65 does not apply to

communication interface.

Â Avoid excessive dust formation.

Â Avoid dust formation with electrically conductive dust

particles.

1

17

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Assembly

Mounting of wall-mounted device

Mounting fixture

Fig. 5 Spacing for position of mounting fixture (indications in mm)

(1) Mounting fixture

(2) Ventilation openings

(3) Slotted piece for mounting bolts

(4) Mounting bolts

(5) Recessed grips

Install the mounting fixture as follows:

Â Unscrew mounting fixture 1 from the back of the inverter.

Â Mark the mounting holes using the mounting fixture as a

template.

t Observe dimensions and distances.

t Observe a minimum distance of 50 cm between inverter and

floor.

t Observe a minimum distance of 50 cm between inverter and

ceiling.

Â Drill the mounting holes and insert the screw anchors.

Â Bolt down mounting fixture 1.

³

525

³ 258

³ 208

³ 204

> 500

3

1

4

5

1

2

PLATINUM Inverter TL

Assembly

18

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

Inverter

Fig. 6 Spacing for mounting of inverters (indications in mm)

Mount inverters as follows:

Â Observe a minimum distance of 50 cm to the floor.

Â Observe a minimum distance of 50 cm to the ceiling.

Â Slide cooling element of the inverter into the mounting fixture 1.

Â Hold the inverter on recessed grips 5 and push up until mounting

bolts 4 drop into slotted pieces for mounting bolts 3 on both

sides.

Â Let down the inverter.

Mounting bolts 4 are seated in the slotted pieces.

Â Verify that minimum distances are kept (see Fig. 6).

Â Verify that the inverter is hanging in the mounting fixture

correctly.

743

³ 150

> 500

262

> 500

19

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

PLATINUM Inverter TL

Assembly

Mounting of free-standing device

Fig. 7 Mounting of free-standing device

(1) Power Block protective housing TL Large

Â Put inverter in intended position.

Â Secure inverter against toppling over and shifting with screws in

base of Power Block protective housing TL Large 1.

1

PLATINUM Inverter TL

Assembly

20

Installation and operating manual: PLATINUM Inverter TL

Version: 04/2011

Mat. No. 749 441-AA

5.5 Connection of the inverter

Note

Terms relating to the alternating voltage side will be combined with

AC below. Terms relating to the direct voltage side will be combined

with DC below.

Danger

Danger to life due to high AC voltage!

Â Switch off the mains power supply (AC side) before

connecting the inverter (fuse).

Â Connect inverter exclusively to TN or TT mains

(see IEC 60364-1) with 230 V.

Â Maximum allowed fuse on alternating voltage side:

40 A, C-characteristics.

Danger

Danger to life due to high DC voltage!

Â Prior to connecting the inverter, verify that voltage is

applied to the generator-side DC terminal.

Â Prior to connecting the inverter, verify that the DC

voltage polarity is correct.

Â Wear insulating protective clothing and face

protection if there is voltage present at the DC input.

Â Remove DC cable exclusively if inverter is out of

operation.

Caution

Risk of burns due to hot surfaces!

After a longer operation with high power, housing

temperatures of > 60 °C are possible.

Â Do not touch hot surfaces.

Caution

Material damage due to DC plug connectors that don’t

fit!

Â Use exclusively DC cable connectors and DC

receptacles of the same type and manufacturer.

Â Make sure that cable connector in latched in socket

correctly.

Page is loading ...

Platinum 13000 TL Installation guide

This manual is also suitable for

Platinum 13000 TL Installation guide

Related papers

Other documents