PERLESMITH PSDSK3 Installation guide

PERLESMITH
Brand
PERLESMITH
Model
PSDSK3
Type
Installation guide
MODEL: PSDSK2
MODEL: PSDSK3
MODEL: PSDSK1
V6.0
SINGLE/DOUBLE / TRIPLE SHELF WALL MOUNT
[email protected]
Stud
Finder
Pencil
1/8 in.
(3.2 mm)
Wood Drill
Screw Driver
Hammer
Level
5/16 in.
(8 mm)
Concrete Drill
Drill
WARNING!
CAUTION!
!
USE WITH PRODUCTS LARGER THAN THE MAXIMUM
WEIGHT AND SIZE MAY RESULT IN INSTABILITY
CAUSING POSSIBLE INJURY. USER MUST REMOVE
TELEVISION OR OBJECT OFF THE BRACKET BEFORE
ADJUSTING. NOT SUITABLE FOR A TV THAT
SURPASSES THE TELEVISION MAXIMUM WEIGHT
CAPACITY AND RECOMMENDED DIAGONAL
MEASURED TV SIZE!
*
*
*
*
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a
qualified installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and
hardware included must be used. If you require replacement parts, contact customer service at
[email protected]
Do not attempt to install or assemble this product if the product or hardware is damaged or missing.
The included hardware is designed for use on vertical walls constructed of wood studs or concrete. A
wood stud wall is defined as consisting of a minimum of 2x4 wooden studs (2” wide by 4” deep)
with a maximum of 5/8” drywall. The included hardware is not designed for use with metal studs or
cinderblock walls. If you’re uncertain about the construction of your wall, then please consult a
qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to
must support 4 times the weight of the total load. If not, then the surface must be reinforced to meet
this standard. The installer is responsible for verifying that the wall structure and hardware used in
any installation method will safely support the total load.
WEIGHT CAPACITY
TOOLS NEEDED
11
Find the stud by the stud finder
and mark the center.
2
Use wall plate (A) to locate two mounting hole locations and
mark with pencil.
A
2
D
C
B
A
X2
X1
PSDSK2 X2
PSDSK1 X1
PSDSK3 X3
PSDSK2 X2
PSDSK1 X1
PSDSK3 X3
PSDSK2 X2
PSDSK1 X1
PSDSK3 X3
PSDSK2 X2
PSDSK1 X1
PSDSK3 X3
Glass bracket
H
G
Ring
PSDSK2 X4
PSDSK1 X2
PSDSK3 X6
Plug
I
PSDSK2 X2
PSDSK1 X1
Thread
PSDSK3 X3
Connector
E2
PSDSK2 X2
PSDSK1 X1
PSDSK3 X3
Connector
E1
PSDSK2 X4
PSDSK1 X2
PSDSK3 X4
Rubber pad A
F1
W-A
Shelf Kits
Wall Kits
PSDSK1 x2
PSDSK2 x4
PSDSK3 x6
Inner Hexagon Screw
M5x10
Allen Key
Lag Bolt
Cable manager
Wall plate
End cap
Glass shelf
Concrete Anchor
S-C
S-B
PSDSK1 x2
PSDSK2 x4
PSDSK3 x6
S-A
Screw M5x12
Washer
C
PSDSK2 X4
PSDSK1 X2
PSDSK3 X6
Rubber pad B
F2
CONTENTS
1a. MOUNT WALL PLATE ON SINGLE STUD
Attention:
Bumps facing
downwards
2
3
Drill pilot holes using a 1/8 in. (3.2 mm)
diameter drill bit.
Secure the wall plate with the lag bolts.
A
3 4
Level
1/8 in.
Ø3.2 mm
2.2in. (55mm)
Use wall bracket holes to locate 2 mounting locations and mark
with pencil. Use level to ensure proper alignment if needed.
Secure 2 wall anchors into drilled
holes with hammer.
Secure wall bracket to concrete wall using screws by
phillips screwdriver.
W-A
W-B
1/8”
(3.2mm)
2
(60mm)
3/8”
(10mm)
2 3/8”
(60mm)
Drill 2 pilot holes into concrete
wall.
W-C
A
A
B
1b. MOUNT WALL PLATE ON CONCRETE
Concrete Only. Do Not Drill into Mortar.
Attention:
Bumps facing
downwards
Attention:
Bumps facing
downwards
Secure the M5x12 screws and the connector to attach the glass
brackets to the wall brackets .
Paste the rubber pad A onto the glass
bracket H Secure glass shelf C to glass
bracket H .
4
Insert the cable manager into the wall
bracket, then attach the end caps .
I
Paste the rubber pad B onto the glass
bracket .
Peel off
F2
F2
F2
F2
H
H
1
S-A
E1 E2
D
B
D
B
A
E2
H
H
E2
E1
H
S-A
CAUTION: Secure the glass to the lower bracket at first, then secure the medium one(for
PSDSK3), AT LAST secure the topper-level one.
S-A
Assemble the glass shelves at the
glass brackets with screws .
Peel off
F1
C
H
S-B
S-C
G
F1
F2
I
E1
Thread
32
H
H
3. END CAPS AND CABLE MANAGER INSTALLATION
2. TEMPERED GLASS INSTALLATION
A
F1
C
Thank you for choosing our product! We strive to provide the
best quality and services for our customers. Would you kindly
share your experience on Amazon if you are satisfied? Should
you have any issues, please don't hesitate to contact us.
Telephone：1-800-556-6806
Mon-Fri 10am - 6pm (PST) (USA)
Email：[email protected]
(US/CA/DE/UK/FR/IT/ES/AU)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

PERLESMITH PSDSK3 Installation guide

PERLESMITH
Brand
PERLESMITH
Model
PSDSK3
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents