Pipishell PILTK4 User manual

Brand
Pipishell
Model
PILTK4
Category
Flat panel wall mounts
Type
User manual
Installation Instructions
V1.0
PILTK4
Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience on
Amazon if you are satisfied? Should you have any issues, please don't
hesitate to contact us.
Telephone：800-556-9829 Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
Supplied Parts
Tools Needed (Not lncluded)
Stud Finder Tape measure
Pencil Drill
5mm
Wood Drill
10mm
Concrete Drill
13mm
socket wrench
Screwdriver
Hammer
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware Lists to assure that all
components were received undamaged. Do not use damaged or defective parts.lf you
require replacement parts, contact customer service at [email protected]
•Not all parts and hardware included will be used.
•Carefully read all instructions before attempting installation.If you do not understand
the instructions or have any concerns or questions, please contact customer service at
[email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
•DO NOT INSTALL INTO DRYWALL ALONE.
1
Wall Plate
Wall Plate
01
x1
02
x1
Bracket Bracket
8mm Wrench
x1 x1
x1
03 04
05
Level
Hardware for Attaching TV Bracket to TV
x4 x8 x8
Philips Screws
M4 x 12mm
M4 x 30mm
x4x4
M-A M-B
Philips Screws
M6 x 15mm
M6 x 30mm
x4x4
M-C M-D
x4
M-E
x4
M-F
Philips Screws
M8 x 15mm
M8 x 45mm
M8 x 65mm
x4
M-G
M-I
Spacers
L10mm
M-J
Spacers
L5mm
M-H
Washers
φ6mm
M4-5-6
Supplied Hardware
Hardware for Attaching Wall Plate to Wall
Lag Bolts
ST7X55
x4 x4
A
These anchors are for concrete
or brick walls ONLY. DO NOT use
them in drywall or wood studs.
CAUTION!
B
Wall Anchor
2
φ10MM
Step 2
FLAT BACK TV
(UNIVERSAL MONITOR PLATE)
Attach the TV Brackets to the TV
3
M-A/M-C
M-H
M-E
Step 1 Measure VESA and Check TV Screws
Check TV screws
When attaching brackets to the flat screen, be
careful not to over tighten screws and be sure that
screws do not bottom out in the mounting holes.
Too Short
Too Long
Correct
Correct
Hand thread screws into the threaded
inserts on the back of your TV to
determine which screw diameter
(M4,M6, or M8) to use.
Measure the distance between the holes located at the back of your TV
(these measures may form the shape of a square, or a rectangle) and
check that these taken measurements are within the VESA(*) range for
this wall mount.
VESA: International standard established by the TV manufacturers used
to determine if LCD/LED TVs are compatble with wall mounts.
Width
Height
200 mm ≈ 7 7/8 in
400 mm ≈ 15 3/4 in
100 mm ≈ 4 in
300 mm ≈ 11 3/4 in
600 mm ≈ 23 6/10 in
or
ROUND BACK TV
(UNIVERSAL MONITOR PLATE)
First, make sure the diameter of the bolt(M-A - M-G) fits your TV. Then, please see
the diagram above. You will need to thread the bolt into the TV using the washer
(M-H) and spacer (M-I or M-J) if necessary with a screwdriver(Not included). Please
make sure the monitor brackets(03/04) are vertically centered and level with each
other.
M-B/M-D
M-H
M-I
M-J
M-F/M-G
M-I
M-J
Step 3
Assemble Mount(Optional)
4
Medium
16’’ Studs
VESA:100X100-400X400mm
24’’ Studs
VESA:100X100-600X400mm
Large
DO NOT overtighten.
Tighten only until snug.
or
Use a stud finder(not
included)to locate wood
studs. Mark the edge and
center locations.
Step 4
Step
4A
X
For wood stud installation, follow STEP 4A
For concrete installation, follow STEP 4B
Attach Wall Plate [01] or [01/02] to Wall
Wood Stud Option
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum
1½ x 3½ in. (38 x 89 mm)
● Stud center must be verified
WARNING:
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A]. Tighten the lag bolts [A] only
until they are pulled firmly against the wall plate
[01] or
[01/02]
.
5
4A-2
4A-3
4A-4
ø5mm
55mm
1/2 in.(13mm)
Socket Wrench
Position the wall plate at
your desired height and
line up the holes with your
stud center line. Level the
wall plate and mark the
holes.
Drill 4 pilot holes using a 5
mm diameter drill bit. Make
sure the depth is not less
than 55mm.
Install the wall plate [01]
or [01/02]. using lag bolts
[A] . Tighten the lag bolts
[A] only until they are
pulled firmly against the
wall plate.
6
A
4B-1 4B-2
ø10mm
60mm
Position the wall plate at your
desired height, level the wall plate
and mark the pilot hole locations.
Drill 4 pilot holes using a 10mm
diameter drill bit. Make sure the
depth is not less than 60mm. Never
drill into the mortar between blocks.
7
Step
4B
Avoid potential personal injury or property damage! DO NOT
over-tighten the lag bolts [A]. Tighten the lag bolts [A] only until they
are pulled firmly against the wall plate [01] or [01/02]. .
WARNING:
Wall
Anchor
B
WARNING:
Ensure the wall plate is securely fastened to the wall
before continuing on to the next step.
WARNING:
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate [01] or [01/02]. directly onto the concrete
surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Solid Concrete or Concrete Block Option
4B-3
Use the hammer to
knock anchors [B] into
the wall.
8
A
B
Install wall plate using lag bolts [A] and anchors [B].
Be sure the anchors [B] are seated flush with the
concrete surface. Tighten the lag bolts [A] only until
they are pulled firmly against the wall plate. DO NOT
over-tighten the lag bolts [A].
Step 5
Ajust the Tilt Tension Screws [S] to Adjust the Tilt Angles of TV
8mm Wrench
03
04
Top of TV
Bottom of TV
S
S
S
S
Loosen
Tighten
S
Loosen the six tilt tension screws [S] on both brackets, adjust the hook of the
bracket to the desired angle, then tighten tilt tension screws with a wrench (not
included) and a screwdriver (not included) to fix the tilting angle of TV.
Locking
03
04
Step 6
Hang TV to the Wall Plate [01] or [01/02].
Step 7
Secure TV
9
Pull down and hold both cords [R], press the bottom of the TV into the wall plate
[01] or [01/02].until the latches lock the TV in place.
HEAVY! You may need assistance with this step.
Press
R
10
Disconnect all cables, pull down and hold both cords [R] while gently pulling the bottom of
the TV away from the wall.
CAUTION: Avoid potential personal injury or property damage! To prevent breaking the
locking latch: always pull and hold the cords [R] down while pulling the TV away from the
wall.
Then lift the TV up and off of wall plate [01] or [01/02]. Place the TV on cardbard or other
protective surface to avoid damage.
NOTE: To rehang the TV, follow the procedures in Step 6 and 7 on PAGE 9.
Removing the TV
HEAVY! You may need
assistance with this step.
Unlocking
R
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Pipishell PILTK4 User manual

Brand
Pipishell
Model
PILTK4
Category
Flat panel wall mounts
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents