H3C S5500-28F-EI Installation guide

H3C S5500-EI Switch Series

Installation Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 20130630-C-1.04

No part of this manu

al may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

3

Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Preface

H3C S5500-EI Switch Series Installation Guide describes the appearance, installation, power-on,

maintenance, and troubleshooting of the S5500-EI switches.

This preface includes:

• Audience

• Conventions

• About the H3C S5500-EI documentation set

• Obtaining documentation

• Technical support

• Documentation feedback

Audience

This documentation is intended for:

• Network planners

• Field technical support and servicing engineers

• Network administrators working with the S5500-EI series

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Descri

p

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

Convention Descri

p

tion

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign can

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

p

tion

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the New User window appears; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

p

tion

WARNING

An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION

An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT

An alert that calls attention to essential information.

NOTE

An alert that contains additional or supplementary information.

TIP

An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Port numbering in examples

The port numbers in this document are for illustration only and might be unavailable on your device.

About the H3C S5500-EI documentation set

The H3C S5500-EI documentation set includes:

Cate

g

or

y

Documents Pur

p

oses

Product

description and

specifications

Marketing brochures Describe product specifications and benefits.

Technology white papers

Provide an in-depth description of software features and

technologies.

Hardware

specifications

and installation

Compliance and safety manual

CE DOCs

Provide regulatory information and the safety

instructions that must be followed during installation.

Quick start

Guides you through initial installation and setup

procedures to help you quickly set up your device.

Installation guide

Provides a complete guide to switch installation and

specifications.

H3C PSR150-A & PSR150-D Series

Power Modules User Manual

Describe the specifications, installation, and

replacement of hot swappable 150W power modules.

RPS Ordering Information for H3C

Low-End Ethernet Switches

Helps you order RPSs for switches that can work with an

RPS.

User manuals for RPSs

Describe the specifications, installation, and

replacement of RPSs.

User manuals for interface cards

Describe the specifications, installation, and

replacement of expansion interface cards.

H3C Low End Series Ethernet

Switches Pluggable Modules

Manual

Describes the specifications of pluggable transceiver

modules.

Pluggable SFP[SFP+][XFP]

Transceiver Modules Installation

Guide

Describe the installation, and replacement of

SFP/SFP+/XFP transceiver modules.

Software

configuration

Configuration guides

Describe software features and configuration

procedures.

Command references Provide a quick reference to all available commands.

Operations and

maintenance

H3C Series Ethernet Switches Login

Password Recovery Manual

Helps you deal with switch login password loss.

Release notes

Provide information about the product release,

including the version history, hardware and software

compatibility matrix, version upgrade information,

technical support information, and software upgrading.

Obtaining documentation

You can access the most up-to-date H3C product documentation on the World Wide Web

at http://www.h3c.com

.

Click the links on the top navigation bar to obtain different categories of product documentation:

[Technical Support & Documents > Technical Documents] – Provides hardware installation, software

upgrading, and software feature configuration and maintenance documentation.

[Products & Solutions]

– Provides information about products and technologies, as well as

solutions. [Technical Support & Documents > Software Download]

– Provides the documentation

released with the software version.

Technical support

servi[email protected]

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

i

Contents

Product overview ·························································································································································· 1

Technical specifications ···················································································································································· 1

Front and rear panels ······················································································································································· 4

S5500-28C-EI&S5500-28C-EI-DC ·························································································································· 4

S5500-52C-EI ··························································································································································· 5

S5500-28F-EI ···························································································································································· 6

S5500-28C-PWR-EI ·················································································································································· 7

S5500-52C-PWR-EI ·················································································································································· 8

Ports ················································································································································································· 10

Console port ·························································································································································· 10

10/100/1000Base-T Ethernet port ···················································································································· 10

SFP port ·································································································································································· 10

Combo interface ···················································································································································· 11

LEDs ················································································································································································· 11

System status LED··················································································································································· 12

Hot swappable power module status LEDs ········································································································· 12

RPS status LED ························································································································································ 12

Port mode LED ························································································································································ 13

Seven-segment LED ················································································································································ 13

10/100/1000Base-T auto-sensing Ethernet port status LED ············································································ 14

SFP port status LED ················································································································································ 15

Interface card status LED ······································································································································· 16

Hot swappable power modules···································································································································· 16

Interface cards ································································································································································ 17

SFP/SFP+/XFP transceiver modules and SFP+/CX4 cables ····················································································· 18

Preparing for installation ··········································································································································· 21

Safety recommendations ··············································································································································· 21

Examining the installation site ······································································································································ 21

Temperature/humidity ·········································································································································· 21

Cleanness ······························································································································································· 22

EMI ·········································································································································································· 22

Laser safety ····························································································································································· 22

Installation tools ······························································································································································ 23

Installing the switch ···················································································································································· 24

Installation flow ······························································································································································ 24

Installing the switch into a 19-inch rack ······················································································································ 25

Installation methods ··············································································································································· 25

Introduction to mounting bracket ························································································································· 26

ii

Rack-mounting by using front mounting brackets ······························································································· 27

Rack-mounting by using mounting brackets and a rack-shelf ··········································································· 28

Rack-mounting by using front and rear mounting brackets ··············································································· 28

Mounting the switch on a workbench ·························································································································· 32

Grounding the switch ···················································································································································· 33

Grounding the switch with a grounding strip ····································································································· 33

Grounding the switch with a grounding conductor buried in the earth ground ············································· 34

Grounding the switch in other grounding environments ··················································································· 35

Installing and removing a hot swappable power module ························································································· 36

Installing the power module ································································································································· 36

Removing the power module································································································································ 37

Connecting the power cords ········································································································································· 37

Connecting the AC power cord ··························································································································· 38

Connecting the –48 VDC power cord ················································································································ 40

Connecting the RPS power cord ·························································································································· 41

Installing and removing an interface card ·················································································································· 42

Installing an interface card ··································································································································· 42

Removing an interface card ································································································································· 43

Installing and removing a dedicated CX4/SFP+ cable ···················································································· 43

Forming an IRF virtual device········································································································································ 44

Flow for forming an IRF virtual device ················································································································ 45

Drawing a plan for an IRF virtual device ············································································································ 46

Verifying the installation ················································································································································ 49

Powering on the switch for the first time ··················································································································· 50

Setting up the configuration environment ···················································································································· 50

Connecting the console cable ······································································································································ 50

Console cable ························································································································································ 50

Connection procedure ·········································································································································· 50

Setting terminal parameters ·········································································································································· 51

Powering on the switch·················································································································································· 54

Maintenance and troubleshooting ···························································································································· 55

Software loading failure ················································································································································ 55

Power supply failure ······················································································································································ 55

Built-in power module failure································································································································ 55

Hot swappable power module failure ················································································································ 57

Fan failure ······································································································································································· 57

Configuration terminal problems ·································································································································· 58

Appendix A Lightning Protection of the Switch ········································································································ 59

Installation of Lightning Arrester for AC Power (Socket Strip with Lightning Protection) ········································ 59

Index ··········································································································································································· 61

1

Product overview

Technical specifications

The S5500-EI Switch Series includes the following models:

• S5500-28C-EI

• S5500-28C-EI-DC

• S5500-52C-EI

• S5500-28F-EI

• S5500-28C-PWR-EI (including the PoE and PoE+ models)

• S5500-52C-PWR-EI (including the PoE and PoE+ models)

Each model has the specifications as shown in Table 1 and Table 2.

Table 1 The S5

50

0-EI Switch Series technical specifications (I)

Item

S5500-28C-

EI-DC

S5500-28C

-EI

S5500-52C-EI S5500-28F-EI

Dimensions (H × W

× D)

43.6 × 440 × 300 mm

(1.72 × 17.32 × 11.81 in)

43.6 × 440 × 300 mm

(1.72 × 17.32 × 11.81

in)

43.6 × 440 × 360 mm

(1.72 × 17.32 × 14.17

in)

Weight

<

5 kg (11.02 lb)

<

5 kg (11.02 lb)

<

6 kg (13.23 lb)

Management port One console port, on the front panel

GE ports

24 × 10/100/1000Base-T

auto-sensing Ethernet port

4 × 1000Base-X SFP port

48 ×

10/100/1000Base-T

auto-sensing Ethernet port

4 × 1000Base-X SFP port

8 ×

10/100/1000Base-T

auto-sensing Ethernet

port

24 × 1000Base-X SFP

port

The last four 10/100/1000Base-T Ethernet ports and the

four SFP ports comprise four combo interfaces.

The last eight SFP ports

and the eight

10/100/1000Base-T

Ethernet ports comprise

eight combo interfaces.

For each combo interface, either the SFP port or the corresponding Ethernet port can be

used at a time. For the combo interface mapping relationship, see Table 5.

Interface card

models supported

(optional)

2, on the rear panel

• 2-port GE SFP interface card (LSPM2GP2P, not supporting IRF)

• Short-haul 2-port 10GE CX4 interface card (LSPM1CX2P, supporting IRF)

• 2-port 10 GE SFP+ interface card (LSPM2SP2P, supporting IRF)

• 2-port 10 GE XFP interface card (LSPM1XP2P, supporting IRF)

• 1-port 10 GE XFP interface card (LSPM1XP1P, supporting IRF)

• 2-port 1/10GBase-T interface card (LSPM1XGT2P, supporting IRF)

2

Item

S5500-28C-

EI-DC

S5500-28C

-EI

S5500-52C-EI S5500-28F-EI

Hot swappable

power modules

N/A N/A

PSR150-A

PSR150-D

PSR150-A1

PSR150-D1

Power supply

system

The S5500-28F-EI is delivered with a hot-swappable power module by default. You can

install another one for backup.

The other three models of the S5500-EI Switch Series are designed with two fixed power

receptacles respectively. The two power inputs can be simultaneously used, acting as

backup for each other. Alternatively, you can use either power input.

Power receptacle

types and quantity

1 –48V DC

power socket

and 1 RPS

power socket

1 AC power

socket and 1

RPS power

socket

1 AC power socket and 1

RPS power socket

PSR150-A/PSR150-A1:

1 AC power socket

PSR150-D/PSR150-D1:

1 –48V DC power socket

Input

voltage

AC

• Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

• Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

–48V

DC

• Rated voltage range: –48 VDC to –60 VDC

• Input voltage range: –36 VDC to –72 VDC

You can use the –48 VDC power supply in the equipment room, or an external RPS

power supply unit recommended by H3C to provide power supply. For relevant

information, see the RPS Ordering Guide for H3C Low-End Series Ethernet Switches.

RPS

The rated voltage range is 10.8 VDC to 13.2 VDC. Use the external RPS power supply

units recommended by H3C only. For relevant information, see the RPS Ordering Guide

for H3C Low-End Series Ethernet Switches.

Minimum power

consumption

27 W 36 W 63 W

PSR150-A/PSR150-A1:

44 W

PSR150-D/PSR150-D1:

30 W

Maximum power

consumption

105 W 110 W 155 W 115 W

Cooling system 4 fans

6 fans (4 for the system,

and 1 for each power

module)

Operating

temperature

0°C to 45°C (32°F to 113°F)

Relative humidity

(noncondensing)

10% to 90%

Table 2 The S5500-EI Switch Series technical specifications (II)

Item

S5500-28C-PWR-EI

S5500-52C-PWR-EI

PoE model PoE+ model

PoE model

PoE+ model

Dimensions (H × W

× D)

43.6 × 440 × 420 mm

(1.72 × 17.32 × 16.54 in)

43.6 × 440 × 420 mm

(1.72 × 17.32 × 16.54 in)

3

Item

S5500-28C-PWR-EI

S5500-52C-PWR-EI

PoE model PoE+ model

PoE model

PoE+ model

Weight < 7.5 kg (16.53 lb) < 8.0 kg (17.64 lb)

Management port 1 console port, on the front panel

GE ports

24 × 10/100/1000Base-T auto-sensing

Ethernet port (support PoE)

4 × 1000Base-X SFP port

48 × 10/100/1000Base-T auto-sensing

Ethernet port (support PoE)

4 × 1000Base-X SFP port

The last four 10/100/1000Base-T Ethernet ports and the four SFP ports comprise four

combo interfaces. For each combo interface, either the SFP port or the corresponding

Ethernet port can be used at a time. For the combo interface mapping relationship,

see Table 5.

Interface card

models supported

(optional)

2, on the rear panel

• 2-port GE SFP interface card (LSPM2GP2P, not supporting IRF)

• Short-haul 2-port 10GE CX4 interface card (LSPM1CX2P, supporting IRF)

• 2-port 10 GE SFP+ interface card (LSPM2SP2P, supporting IRF)

• 2-port 10 GE XFP interface card (LSPM1XP2P, supporting IRF)

• 1-port 10 GE XFP interface card (LSPM1XP1P, supporting IRF)

• 2-port 1/10GBase-T interface card (LSPM1XGT2P, supporting IRF)

Power supply

system

S5500-28C-PWR-EI and S5500-52C-PWR-EI are each designed with two fixed power

receptacles, an AC receptacle, and an RPS receptacle.

The two power inputs can be simultaneously used, acting as backup for each other.

Alternatively, you can use either power input.

Input

voltage

AC

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

RPS

The rated voltage range is –55 VDC to –52 VDC. Use the external RPS power supply

units recommended by H3C only. For relevant information, see the RPS Ordering Guide

for H3C Low-End Series Ethernet Switches.

Maximum PoE

power per port

15.4 W 30 W 15.4 W 30 W

Total PoE power 370 W 370 W

AC power supply: 370 W

RPS power supply: 740 W (The total PoE

power of ports numbered 1 through 24 is

370 W, and that of ports numbered 25

through 48 is 370 W.)

Minimum power

consumption

60 W 60 W 83 W 85 W

Maximum

power

consumptio

n (including

PoE power)

AC 205 W + 370 W 221 W + 370 W 270 W + 370 W 291 W + 370 W

RPS 115 W + 370 W 122 W + 370 W 170 W + 740 W 190 W + 740 W

Cooling system 6 fans

Operating

temperature

0°C to 45°C (32°F to 113°F)

4

Item

S5500-28C-PWR-EI

S5500-52C-PWR-EI

PoE model PoE+ model

PoE model

PoE+ model

Relative humidity

(noncondensing)

10% to 90%

CAUTION:

• Only the recommended RPS can be used for the RPS receptacles on S5500-EI Switch Series. The –48

VDC in the equipment room cannot be used directly. Otherwise, the device might be damaged.

• For more information about the RPS power supply units, see the RPS user manuals and

RPS Ordering

Guide for H3C Low-End Series Ethernet Switches.

Front and rear panels

S5500-28C-EI&S5500-28C-EI-DC

Figure 1 Front panel of the S5500-28C-EI&S5500-28C-EI-DC switch

(1) 10/100/1000 Base-T auto-sensing Ethernet port

(2) 10/100/1000 Base-T auto-sensin

g

Ethernet port status LED

(3) 1000 Base-X SFP port (4)

1000Base-X SFP port status LED

(5) Console port (6) Seven-segment LED

(7) Port mode LED (Mode) (8)

System status LED (PWR)

(9) RPS status LED (RPS) (10) Interface card 1 status LED (MOD1)

(11) Interface card 2 status LED (MOD2) (12) Port status LED mode switching button

Figure 2 Rear panel of the S5500-28C-EI switch

(1) AC power input (2) RPS power input (shipped with a protective cover)

(3) Groundin

g

screw (4) Interface card slot 1

(MOD1)

(5) Interface card slot 2 (MOD2)

5

Figure 3 Rear panel of the S5500-28C-EI-DC switch

(1) –48V DC power input (2) RPS power input (shipped with a protective cover)

(3) Groundin

g

screw (4) Interface card slot 1

(MOD1)

(5) Interface card slot 2 (MOD2)

NOTE:

The S5500-28C-EI/S5500-28C-EI-DC is shipped with the two expansion interface card slots covered b

y

filler panels. You can select one or two interface cards for your switch as needed. For the interface cards

available for the S5500-EI Switch Series, see "Interface cards." For how to install an

interface card, see

"Installing and removing an interface card."

S5500-52C-EI

Figure 4 Front panel of the S5500-52C-EI switch

(1) 10/100/1000 Base-T auto-sensin

g

Ethernet port

(2) 10/100/1000 Base-T auto-sensin

g

Ethernet port status LED

(3) Console port (4) Seven-segment LED

(5) Port mode LED (Mode) (6)

System status LED (PWR)

(7) RPS status LED (RPS) (8)

Interface card 1 status LED (MOD1)

(9) Interface card 2 status LED (MOD2) (10) Port status LED mode switching button

(11) 1000 Base-X

SFP port (12)

1000Base-X SFP port status LED

Figure 5 Rear panel of the S5500-52C-EI switch

(1) AC power input (2) RPS

power input

(shipped with a protective cover)

(1) (2) (3) (4) (5)

(6)

(7)

(8)

(9)(10)(11)(12)

6

(3) Groundin

g

screw (4) Interface card slot 1

(MOD1)

(5) Interface card slot 2 (MOD2)

NOTE:

The S5500-52C-EI is shipped with the two expansion interface card slots covered by filler panels. You can

select one or two interface cards for your switch as needed. For the interface cards available for the

S5500-EI Switch Series, see "Interface cards." For how to install an inte

rface card, see "Installing and

removing an interface card."

S5500-28F-EI

Figure 6 Front panel of the S5500-28F-EI switch

(1) SFP port (2) SFP port status LED

(3) 10/100/1000 Base-T auto-sensing Ethernet

port

(4) 10/100/1000 Base-T auto-sensing Ethernet port

status LED

(5) Console port (6)

Port status LED mode switchin

g

button

(7) Interface card 1 status LED (MOD1) (8) Interface card 2 status LED (MOD2)

(9) System status LED (SYS) (10)

Hot swappable power module 1 status LED (PWR1)

(11) Hot swappable power module 2 status LED

(PWR2)

(12) Port mode LED (Mode)

(13) Seven-segment LED

Figure 7 Rear panel of the S5500-28F-EI switch

(1) Grounding screw (2) Hot swappable power module 1 (a PSR150-A)

(3) Hot swappable power module 2

(a PSR150-D)

(4) Interface card slot 1

(MOD1)

(5) Interface card slot 2 (MOD2)

(2) (4) (5) (6)

(8)

(9)

(10)

(11)

(12)

(13)

(7)

(1)

(3)

7

CAUTION:

• The S5500-28F-EI is shipped with the two expansion interface card slots covered by filler panels. You

can select one or two interface cards for your switch as needed. For the interface cards available for the

S5500-EI Switch Series, see "Interface cards." Fo

r how to install an interface card, see "Installing and

removing an interface card."

• The S5500-28F-EI switch is shipped with power module slot 1 installed with a power module and powe

r

module slot 2 installed with a filler panel. You can install a power module in PWR2 to serve as a backup.

For more information about the available power modules, see "Hot swappable power modules"

For

how to install and remove a power module, see "Installing and removing a hot swappable power

module."

S5500-28C-PWR-EI

The S5500-28C-PWR-EI includes two models: PoE and PoE+.

• The front panels of the PoE and PoE+ models are the same in appearance. See Figure 8.

• The P

oE+ model has a PoE+ label on its rear panel, as shown in Figure 9. The maximum PoE power

per por

t is 30 W.

• The PoE model has no PoE+ label on its rear panel, as shown in Figure 10. The maximum PoE power

per por

t is 15.4 W.

For more information about the PoE power supply, see Table 2.

Figure 8 Front panel of

the S5

500-28C-PWR-EI switch

(1) 10/100/1000 Base-T auto-sensin

g

Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) 1000 Base-X SFP port (4)

1000Base-X SFP port status LED

(5) Console port (6)

Seven-se

g

ment LED

(7) Port mode LED (Mode) (8) System status LED (PWR)

(9) RPS status LED (RPS) (10) Interface card 1 status LED (MOD1)

(11) Interface card 2 status LED (MOD2)

(12)

Port status LED mode switchin

g

button

8

Figure 9 Rear panel of the S5500-28C-PWR-EI switch (PoE+ model)

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface card slot 1 (MOD1)

(5) Interface card slot 2 (MOD2) (6)

PoE+ label

Figure 10 Rear panel of the S5500-28C-PWR-EI switch (PoE model)

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface card slot 1 (MOD1)

(5) Interface card slot 2 (MOD2)

NOTE:

The S5500-28C-PWR-EI is shipped with the two expansion interface card slots covered by filler panels.

You can select one or two interface cards for your switch as needed. For the interface cards available for

the S5500-EI Switch Series, see "Interface cards." For how to install an interface card,

see "Installing and

removing an interface card."

S5500-52C-PWR-EI

S5500-52C-PWR-EI includes two models: PoE and PoE+.

• The front panels of the PoE and PoE+ models are the same in appearance. See Figure 11.

• The P

oE+ model has a PoE+ label on its rear panel, as shown in Figure 12. The maximum PoE power

per por

t is 30 W.

• The PoE model has no PoE+ label on its rear panel, as shown in Figure 13. The maximum PoE power

per por

t is 15.4 W.

For more information about the PoE power supply, see Table 2.

9

Figure 11 Front panel of the S5500-52C-PWR-EI switch

(1) 10/100/1000 Base-T auto-sensin

g

Ethernet port

(2) 10/100/1000 Base-T auto-sensing Ethernet port status LED

(3) Console port (4)

Seven-se

g

ment LED

(5) Port mode LED (Mode) (6)

System status LED (PWR)

(7) RPS status LED (RPS) (8) Interface card 1 status LED (MOD1)

(9) Interface card 2 status LED (MOD2) (10) Port status LED mode switchin

g

button

(11) 1000 Base-X

SFP port (12)

1000Base-X SFP port status LED

Figure 12 Rear panel of the S5500-52C-PWR-EI switch (PoE+ model)

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface card slot 1 (MOD1)

(5) Interface card slot 2 (MOD2) (6)

PoE+ label

Figure 13 Rear panel of the S5500-52C-PWR-EI switch (PoE model)

(1) RPS power input (2) AC power input

(3) Grounding screw (4) Interface card slot 1 (MOD1)

(5) Interface card slot 2 (MOD2)

10

NOTE:

The S5500-52C-PWR-EI is shipped with the two expansion interface card slots covered by filler panels.

You can select one or two interface cards for your switch as needed. For the interface cards available for

the S5500-EI Switch Series, see "Interface cards." For how to install an interface card,

see "Installing and

removing an interface card."

Ports

Console port

Each S5500-EI switch provides one console port on the front panel.

Table 3 Console port specifications

Item S

p

ecification

Connector type

RJ-45

Compliant standard

Asynchronous EIA/TIA-232

Transmission baud rate 9600 bps (default) to 115200 bps

Service

• Provides connection to an ASCII terminal.

• Provides connection to the serial port of a local or remote (through a

pair of modems) PC running terminal emulation program.

10/100/1000Base-T Ethernet port

Table 4 10/100/1000Base-T Ethernet port specifications

Item S

p

ecification

Connector type

RJ-45

Interface standard

• 10 Mbps, half/full duplex

• 100 Mbps, half/full duplex

• 1000 Mbps, full duplex

• MDI/MDI-X, auto-sensing

Max transmission distance

100 m (328.08 ft)

Transmission medium

Category-5 (or above) twisted pair cable

Standards

IEEE 802.3i, 802.3u, 802.3ab

SFP port

The S5500-EI Switch Series provides 1000Base-X SFP ports, and you can install the 1000 Mbps and 100

Mbps SFP transceiver modules, as shown in Table 18 and Table 19, in the port

s.

11

Combo interface

One SFP port and the corresponding 10/100/1000Base-T Ethernet port form a combo interface. For

each combo interface, either the SFP port or the corresponding 10/100/1000Base-T Ethernet port can

be used at a time. For more information about combo interfaces, see the Layer 2—LAN switching

configuration guide for the switch.

Table 5 Combo interface mapping relationship

Model SFP

p

ort 10/100/1000Base-T Ethernet

p

ort

S5500-28C-EI

S5500-28C-EI-DC

S5500-28C-PWR-EI

GigabitEthernet 1/0/25 GigabitEthernet 1/0/22

GigabitEthernet 1/0/26 GigabitEthernet 1/0/24

GigabitEthernet 1/0/27 GigabitEthernet 1/0/21

GigabitEthernet 1/0/28 GigabitEthernet 1/0/23

S5500-52C-EI

S5500-52C-PWR-EI

GigabitEthernet 1/0/49 GigabitEthernet 1/0/46

GigabitEthernet 1/0/50 GigabitEthernet 1/0/48

GigabitEthernet 1/0/51 GigabitEthernet 1/0/45

GigabitEthernet 1/0/52 GigabitEthernet 1/0/47

S5500-28F-EI

GigabitEthernet 1/0/17 GigabitEthernet 1/0/25

GigabitEthernet 1/0/18 GigabitEthernet 1/0/26

GigabitEthernet 1/0/19 GigabitEthernet 1/0/27

GigabitEthernet 1/0/20 GigabitEthernet 1/0/28

GigabitEthernet 1/0/21 GigabitEthernet 1/0/29

GigabitEthernet 1/0/22 GigabitEthernet 1/0/30

GigabitEthernet 1/0/23 GigabitEthernet 1/0/31

GigabitEthernet 1/0/24 GigabitEthernet 1/0/32

LEDs

Table 6 LEDs at a glance

LED Availabilit

y

System status LED Entire series

Hot swappable power module status LEDs S5500-28F-EI

RPS status LED Entire series (except the S5500-28F-EI)

Port mode LED Entire series

Seven-segment LED Entire series

10/100/1000Base-T auto-sensing Ethernet port status

LED

Entire series

SFP port status LED Entire series

Interface card status LED Entire series

12

System status LED

The system status LED shows the operating status of the switch.

Table 7 System status LED description

LED Status Descri

p

tion

SYS/PWR

Steady green The switch is operating correctly.

Flashing green (1 Hz) The switch is performing power-on self test (POST).

Steady red POST has failed.

Flashing yellow (1 Hz) Some ports have failed to pass POST.

Off The switch is powered off.

Hot swappable power module status LEDs

Each power module slot has a status LED to show the operating status of the hot swappable power

module in the slot. Only the S5500-28F-EI supports this type of LEDs.

Table 8 Hot swappable power module status LED description

LED Status Descri

p

tion

PWR1/PWR2

Steady green

A power module is installed in the power module slot,

and the power output is normal.

Steady yellow

A power module is installed in the power module slot,

but the power module is experiencing an output error

or is not powered on.

Off

No power module is installed in the power module

slot.

RPS status LED

The RPS status LED shows the operating status of the RPS. The S5500-28F-EI does not support the RPS

status LED.

Table 9 RPS status LED

LED Mar

k

Status

Descri

p

tion

RPS status LED

(S5500-28C-EI and

S5500-52C-EI)

RPS

Steady green

Power input on the RPS interface is normal or

the RPS is in position, and AC input on the

AC power interface is normal.

Steady yellow

Power input on the RPS interface is normal,

but AC input has failed or AC input is not

connected.

Off RPS interface is not connected.

RPS status LED

(S5500-28C-EI-DC)

RPS Steady green

The –48V DC input is normal, and the RPS is

in the position or operates correctly.

Page is loading ...

H3C S5500-28F-EI Installation guide

This manual is also suitable for

H3C S5500-28F-EI Installation guide

Related papers

Other documents