Page is loading ...
Automatic
Hook Bolt Lock A
EN Installation instructions
186500-00
Hook bolt Lock A
2
Contents
1 Introduction...............................................................................................................................................................3
1.1 Symbols and illustrations ..............................................................................................................................................................................3
1.2 Revisions and validity......................................................................................................................................................................................3
1.3 Product liability .................................................................................................................................................................................................3
1.4 Reference documents ..................................................................................................................................................................................... 3
1.5 Abbreviations ..................................................................................................................................................................................................... 4
2 Fundamental safety precautions .......................................................................................................................4
2.1 Intended use.......................................................................................................................................................................................................4
2.2 Safety notices ..................................................................................................................................................................................................... 4
2.3 Safety-conscious working .............................................................................................................................................................................4
2.4 Inspection of the installed system .............................................................................................................................................................5
2.5 Environmentally conscious working .........................................................................................................................................................5
2.6 Qualication .......................................................................................................................................................................................................5
3 Overview.....................................................................................................................................................................5
3.1 Diagrams ..............................................................................................................................................................................................................5
3.2 Tools and aids .....................................................................................................................................................................................................6
3.3 Torques .................................................................................................................................................................................................................6
4 Installation ..................................................................................................................................................................7
4.1 Installing hook bolt lock A in the side screen prole ..........................................................................................................................7
4.2 Installing the transmission element with ECdrive ..............................................................................................................................12
4.3 Installing the transmission element with ECdrive T2 ........................................................................................................................18
4.4 Installing the transmission unit with Slimdrive SL NT ...................................................................................................................... 23
4.5 Post installation, 1-leaf ................................................................................................................................................................................. 26
4.6 Emergency activation ...................................................................................................................................................................................31
5 Service and maintenance .................................................................................................................................. 33
6 Troubleshooting .................................................................................................................................................... 33
Hook bolt Lock A
3
Introduction
1 Introduction
1.1 Symbols and illustrations
Warning notices
In these instructions, warnings are used to warn against material damage and injuries.
XAlways read and observe these warnings.
XObserve all measures marked with the warning symbol and warning word .
Warning symbol
Warning word Meaning
WARNING Danger for individuals.
Non-compliance can result in death or serious injuries.
More symbols and illustrations
Important information and technical notes are highlighted to explain correct operation.
Symbol Meaning
means “important note”.
Information to prevent property damage, to understand or optimise the operation sequences.
means “additional Information”
X Symbol for an action: This means you have to do something.
XIf there are several actions to be taken, keep to the given order.
1.2 Revisions and validity
Version 02: valid for version ECdrive T2, ECdrive T2-FR, ECdrive, ECdrive-FR, SL NT and SL NT-FR from year of
manufacture 2019.
1.3 Product liability
In compliance with the liability of the manufacturer for his products as dened in the German “Product Liability
Act”, compliance with the information contained in this brochure (product information and intended use, misuse,
product performance, product maintenance, obligations to provide information and instructions) must be en-
sured. Failure to comply releases the manufacturer from his statutory liability.
1.4 Reference documents
Type Name
Wiring diagram DCU1-NT DCU1-2M-NT
User manual
Errors and corrective measures
Cable plan
Installation instructions ECdrive T2
Installation instructions ECdrive T2 VP-Kit
Installation instructions ECdrive T2 carrier and side panel
Installation instructions ECdrive
Installation instructions Girder section ECdrive
Installation instructions SL NT
Installation instructions Girder section SL NT
Installation instructions Leaf and side panel prole systems
The diagrams are subject to change without notice. Use only the most recent version.
Hook bolt Lock A
4
Fundamental safety precautions
1.5 Abbreviations
HSK Main closing edge
OKFF Finished oor level
2 Fundamental safety precautions
To ensure personal safety, it is important to follow these safety instructions.
These instructions must be kept.
2.1 Intended use
The hook bolt locks A are only suitable for use
àin dry rooms
àin automatic door systems for horizontal door leaves
àin entrances and interior areas of pedestrian trac in commercial plants and public areas
The hook bolt locks must not be used in re and smoke protection doors.
2.2 Safety notices
àThe mandatory installation, maintenance and repair work must be performed by properly trained personnel
authorised by GEZE.
àThe country-specic laws and regulations are to be observed during safety-related tests.
àIf unauthorised changes are made to the system, GEZE cannot be held liable in any way whatsoever for any
resulting damage, and the approval for use in emergency exits ceases.
àGEZE does not accept any warranty for combinations with third-party products.
àFurthermore, only original GEZE parts may be used for repair and maintenance work.
àThe connection to the mains voltage must be made by a professional electrician. Perform the power connec-
tion and equipment earth conductor test in accordance with VDE 0100 Part 610.
àUse an on-site 10-A overload cut-out as the line-side disconnecting device.
àIn compliance with Machinery Directive (2006/42/EC), a risk analysis must be performed and the door system
identied in accordance with CE Marking Directive 93/68/EEC before the door system is commissioned.
àObserve the current status of directives, standards and country-specic regulations, especially:
àDIN 18650: 2010-06 “Building hardware– Powered pedestrian doors”
àVDE 0100, Part 610: 2004-04 "Installing Electrical Power Systems with Nominal Voltages up to 1000 V"
àDIN EN 16005: 2013-01 "Power operated pedestrian doorsets; safety in use; Requirements and test methods"
àDIN EN 60335-1: 2012-10 “Safety of electrical devices for home use and similar purposes - Part 1: General
requirements IEC 60335-1: 2010, modied, German version EN 60335-1: 2012
àDIN EN 60335-2-103: 2016-05 “Safety of electrical devices for home use and similar purposes - Part 2-103:
Special requirements for drives for gates, doors and windows. (IEC 60335-2-103: 2006, modied + A1:2010,
modied); German version EN 60335-2-103: 2015
The product should be installed or incorporated in such a way that eortless access to the product is guaranteed
during any repairs and/or maintenance, and that any removal costs do not stand out of proportion to the value
of the product
2.3 Safety-conscious working
àSecure workplace against unauthorised entry.
àWatch the swivelling range of long system parts.
àNever carry out work with a high safety risk (e.g. installing the drive, cover or door leaf) while alone.
àSecure the cover/drive panels against falling.
àUse only the cables prescribed in the cable plan provided. Cables must be shielded in compliance with the
wiring diagram.
àSecure loose, internal drive cables with cable ties.
àBefore working on the electrical system:
àDisconnect the drive from the 230/115 V mains and check to ensure that it is not supplied with power.
àDisconnect the control unit from the 24 V rechargeable battery.
àWhen an Uninterruptible Power Supply (UPS) is used, the system will still be under voltage even when
disconnected from the mains.
àAlways use insulated wire-end ferrules for wire cores.
àAttach safety stickers to glass leaves.
àDanger of injury with opened drive. Hair, clothing, cables, etc. can be drawn in by rotating parts.
Hook bolt Lock A
5
Overview
àDanger of injury caused by unsecured crushing, impact, drawing-in or shearing spots.
àDanger of injury due to broken glass.
àDanger of injury due to sharp edges in the drive.
àDanger of injury during installation through freely moving parts.
2.4 Inspection of the installed system
Measures for protection and prevention of pinching, impact, shearing or drawing-in spots:
àCheck the function of safety sensors and movement detectors.
àCheck protective earth connection to all metal parts that can be touched.
àPerform a safety analysis (risk analysis).
2.5 Environmentally conscious working
àWhen disposing of the door system, separate the dierent materials and have them recycled.
àDo not dispose of batteries and rechargeable batteries with household waste.
àComply with the statutory regulations when disposing of the door system and the batteries/rechargeable
batteries.
2.6 Qualication
Installation of the GEZE sliding door drive may only be carried out by experts authorised by GEZE.
3 Overview
3.1 Diagrams
Drawing no. Description
70518-0-001 Drive drawing ECdrive T2
70504-9-0981
70504-0-001
Drive drawing EC
70 511- 9 - 0953
70511-0-001
Drive drawing SL NT
–Wiring diagram DCU1, DCU1-2M
70715-9-9883
70715-9-9884
Leaf drawing EC T2
70715-9-9862
70715-9-9868
Leaf drawing EC
70715-9-9863 Leaf drawing SL NT
70518-ep21/-ep22/-ep25/-ep26/-ep29/
-ep30/-ep33/-ep34
Installation diagrams EC T2
70504-ep19/-ep20 Installation diagrams EC
70511-ep16/-ep17 Installation diagrams SL NT
Hook bolt Lock A
6
Overview
3.2 Tools and aids
Tool Size/remark
Tape measure
Marking pen
Torque spanner
Allen key 1.5mm; 2.5 mm; 4 mm; 5 mm
Open-ended spanner 8 mm; 10 mm; 13 mm; 15 mm
Ring spanner 8 mm; 10 mm
Screwdriver set Slotted up to 6 mm, cross-slot PH2 or PZ2
Torx spanner T × 20; T × 25
Side-cutting pliers
Crimping pliers for cables
Wire stripper
Multimeter
Installation tool Lock A Mat. no. 153719
Cable ties 2.5 × approx. 100
Metal drill Ø 2.8mm
3.3 Torques
The torques are given in the specic installation step, the drive drawing and the leaf drawings.
Hook bolt Lock A
7
Installation
4 Installation
4.1 Installing hook bolt lock A in the side screen prole
4.1.1 Install the strike plate in the side screen (1- and 2-leaf)
Hook bolt Lock A
8
Installation
4.1.2 Install the drive and hook bolt locks in the side screen bolts
The hook bolt locks are available in versions with single or double locking. The illustration below shows the ver-
sion with double locking in the locked state.
1 Side screen bolt
2 Upper hook bolt lock
3 Connecting link arm
4 Holder
5 Drive hook bolt lock
6 Lower hook bolt lock
Factory setting
The side screen bolts are delivered unlocked.
Hook bolt Lock A
9
Installation
Preparation for installation – version with one hook bolt lock
1.5 Nm
Hook bolt Lock A
10
Installation
Preparation for installation – version with two hook bolt locks
1.5 Nm
Hook bolt Lock A
11
Installation
Installing the hook bolt locks
XPush the connecting link arm in until the
marking can be seen as shown in the diagram
on the right.
The optimum position for the installation of the
hook bolt locks has then been reached.
XWhen installing two hook bolt locks make sure that the hooks of the driving rod catch the connecting link arm
as shown below (see arrows).
2.5 Nm
2.5 Nm
Hook bolt Lock A
12
Installation
Attaching the rubber seals
(illustration with 2 hook bolt locks)
4.2 Installing the transmission element with ECdrive
4.2.1 ECdrive, 1-leaf, right hand slide to open
XAdjust the position of the stop buer in closed position without rubber buer after door installation and calibration
.
When the door is closed the stop buer must not be ush. The distance should be about 1 mm.
Installing the spring-mounted unit
Hook bolt Lock A
13
Installation
Installing the unit without spring-mounting
XMove the moving leaf towards the closed position.
Closed position Open position
Hook bolt Lock A
14
Installation
Closed position
Hook bolt Lock A
15
Installation
4.2.2 ECdrive, 1-leaf, left hand slide to open, 2-leaf
XAdjust the position of the stop buer after door installation and calibration.
When the door is closed the stop buer must not be ush. The distance should be about 1 mm.
With 2-leaf systems:
XInstall 2 additional stop buers before installing the roller carriage in the centre of the system.
XInstall the stop buers (3) in such a way that the rubber buers (2) are not pointing towards the roller carriage (1).
or
XInstall the stop buers on the main closing edge without rubber buers.
The additional stop buers protect the contacts when the door leaves are disconnected from the toothed belt.
Installing the spring-mounted unit
Hook bolt Lock A
16
Installation
Installing the unit without spring-mounting
XMove the moving leaf towards the closed position.
Open position Closed position
Hook bolt Lock A
17
Installation
Closed position
Hook bolt Lock A
18
Installation
4.3 Installing the transmission element with ECdrive T2
4.3.1 ECdrive T2, 1-leaf, right hand slide to open
XAdjust the position of the stop buer in closed position without rubber buer after door installation and
calibration.
When the door is closed the stop buer must not be ush. The distance should be about 1 mm.
Installing the spring-mounted unit
XScrew the spring-mounted unit (1) to the buer (2).
1
2
Installing the unit without spring-mounting
Hook bolt Lock A
19
Installation
XMove the moving leaf towards the closed position.
Closed position Open position
Closed position
Hook bolt Lock A
20
Installation
4.3.2 ECdrive T2, 1-leaf, left hand slide to open, 2-leaf
Installing the spring-mounted unit
XScrew the spring-mounted unit (1) to the buer (2).
1
2
/
