Extron electronics MP 101 D User manual

Brand: Extron electronics

Model: MP 101 D

Type: User manual

This manual is also suitable for

User Guide

MP 101 Series

Category

Microphone to Line Preampliﬁers

68-992-02 Rev. B

04 19

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within the

product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer darauf

aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes

gefährliche Spannungen herrschen, die nicht isoliert sind und die einen

elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec le

matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron, réf.

68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire

l’utente della presenza di importanti istruzioni di funzionamento e

manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68-290-01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji

wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,

zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część

numer 68-290-01, na stronie internetowej Extron, www.extron.com.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資

訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規

遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守(整備)の指示についてユーザーの注意

を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より『 Extron Safety

and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

), registered service marks (

), and trademarks (

) are the property of RGBSystems, Inc. or

ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free. Global

Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink,

MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch,

StudioStation, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP,

XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS(ClassD

Ripple Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,

DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk,

MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger,

ShareLink, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and

ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

NOTES:

• (if only this paragraph is used, reformat to single NOTE format.) For

more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

VCCI-A Notice

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると、電波妨害を引き

起こすことがあります。その場合には使用者が適切な対策を講ずるよう要求されることがあります。

ＶＣＣI－Ａ

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.

aspx.

Contents

Introduction ................................................1

About this Manual................................................ 1

About the MP 101, MP 101 AAP, and

MP 101 D ........................................................... 1

Features .............................................................. 1

MP 101 Series Rear Panels ..........................2

Rear Panel Features ............................................ 2

Power Connector ............................................ 2

Remote Connection ......................................... 4

Mic Input (Microphone Level) ........................... 4

Audio Output (Line Level) ................................. 5

Low Cut Filter Switch ....................................... 5

Phantom Power ............................................... 5

MP 101 .......................................................6

Front Panel Features ............................................ 6

Mounting the MP 101 .......................................... 6

Adjusting the MP 101 .......................................... 7

Remote Control ................................................... 7

Remote Connector Wiring ............................... 7

Remote Control Options .................................. 7

MP 101 AAP ................................................8

Front Panel Features ............................................ 8

Adjusting the MP 101 AAP .................................. 9

Mounting the MP 101 AAP .............................. 9

Remote Control ................................................. 10

Remote Connector Wiring ............................. 10

Remote Control Options ................................ 11

MP 101 D ..................................................12

Front Panel Features .......................................... 12

Adjusting the MP 101 D ..................................... 12

Mounting the MP 101 D .................................... 13

Remote Control ................................................. 14

Remote Connector Wiring ............................. 14

Remote Control Options ................................ 14

Architectural Installation ............................15

Installation Instructions ...................................... 15

Preparing the Site and Installing the Wall Box .... 15

Dimensions and Template for the

MP101D ..................................................18

Dimensions........................................................ 18

Template............................................................ 19

vTechnical Publications Standards and Styles • Contents

Technical Publications Standards and Styles • Contents vi

MP 101 Series • Introduction 1

Introduction

About this Manual

This manual contains information about the MP 101, the MP 101 AAP, and the MP 101 D

microphone to line preamplifiers and provides instructions on how to mount and operate

these units.

About the MP 101, MP 101 AAP, and MP 101 D

The Extron MP 101, MP 101 AAP, and MP 101 D (the MP 101 Series) are high quality

microphone to line level audio preamplifiers. These products can add microphone capability

to most Extron audio and switcher systems.

The MP 101 is rack-mountable, while the MP 101 AAP is an AAP plate option for easy

integration into Extron architectural products. The MP 101 D works similarly to the other two

units, but features a Decorator-style wallplate mounting option. Information on its installation

and operation are found in MP 101 D starting on page12.

Each model features a recessed Mic Gain potentiometer that provides a 25 to 72 dB

adjustment range, compensating for different microphone sensitivities. Each model also

features an on/off switch for 48 volt phantom power and low cut filtering. Remote control is

available through optional Extron VCM 110 AAP panel, which control volume and muting.

Features

• Compact size — The MP 101 is housed in a 1U high, 1/8 rack width, 3” deep, metal

enclosure, the MP 101 AAP is housed in a two-space AAP plate; and the MP 101 D is

mounted into a wallplate. These three options allow for diverse applications.

• Quick plug input and outputs — Connectors are captive screw or XLR (MP 101 AAP

and MP 101 D only) for quick installation.

• Gain control — Provides a wide gain adjustment range of 25 to 72 dB.

• Switchable low cut filter — Provides low cut filter to remove wind and “table rumble”

noise.

• Switchable phantom power — Provides 48 volt phantom power for condenser

microphones.

• Volume and mute remote control — Each model can be remotely controlled for

volume adjustment and muting via a rear panel Remote connector.

• Flexible mounting options — The MP 101 can be mounted on a rack, on a table, or

under furniture. The MP 101 AAP mounts into various Extron architectural products.

The MP 101 D is wall mountable using standard, off-the-shelf mounting accessories.

• External international power supply — The autoswitchable, 12 VDC, 0.5 A external

power supply provides worldwide power compatibility.

MP 101 Series • MP 101 Series Rear Panels 2

MP 101 Series Rear

Panels

This section covers rear panel feature for the MP 101, the MP 101 APP, and the MP101D.

Rear Panel Features

POWER

12V

0.3A MAX

MIC

INPUT

REMOTE

VOL/MUTE

MP 101

MIC TO LINE

PREAMPLIFIER

10V

LINE

OUTPUT

11224

MP 101 MP 101 AAP MP 101 D

Power Connector

Audio Output (Line Level) (MP 101 only)

Power LED (MP 101 only)

Low Cut Filter Switch (MP 101 APP and MP 101 D)

Remote Connection

Phantom Power (MP 101 APP and MP 101 D)

Mic Input

Figure 1. MP 101, MP 101 APP, and MP 101 D Rear Panel

Power Connector

Power connector — An external 12 V power supply is included with the unit. Plug it

into this 2-pole captive screw connector. Wire the connector as shown below.

Rear Panel

Power Receptacle

DC Power Cord

Captive Screw

Connector

Ground

all devices.

External

Power Supply

(12 VDC, 0.5 A max.

)

– Return

+12 VDC input

Ridged

Smooth

Power Supply

Output Cord

Captive Screw

Connector

3/16" (5 mm) MAX

SECTION A–A

Ridges

Smooth

A A

To verify the polarity before connection, plug in the power supply

with no load and check the output with a voltmeter.

Figure 2. Rear Panel 12 VDC Power Connector

MP 101 Series • MP 101 Series Rear Panels 3

ATTENTION:

• The DC output cables must be kept separate from each other while the power

supply is plugged in. Remove power before wiring

• Les câbles de sortie CC doivent être séparés les uns des autres tant que la

source d’alimentation est branchée. Coupez l’alimentation avant d’effectuer les

raccordements.

• Do not connect power to the amplifier until you have read the ATTENTION

notifications.

• Ne branchez pas l’alimentation au l’amplificateur avant d’avoir lu les mises en garde

« ATTENTION ».

• Always use a power supply supplied or specified by Extron. Use of an unauthorized

power supply voids all regulatory compliance certification and may cause damage

to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute certification de

conformité réglementaire et peut endommager la source d’alimentation et l’unité.

• If not provided with a power supply, this product is intended to be supplied by a

power source marked “Class 2” or “LPS” and rated at 12VDC and a minimum of

0.5A.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par

une source d’alimentation de classe 2 ou LPS, avec une tension nominale 12 Vcc,

0,5 A minimum.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical

Code part 1, section 16. The power supply shall not be permanently fixed to

building structure or similar structure.

• Cette installation doit toujours être conforme aux dispositions applicables du Code

américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et

du Code canadien de l’électricité, partie1, section16. La source d’alimentation ne

devra pas être fixée de façon permanente à une structure de bâtiment ou à une

structure similaire.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the

power supply and the unit. The ridges on the side of the cord (see ﬁgure2 on the

previous page) identify the power cord negative lead.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté

du cordon (voir ﬁgure2) permettent de repérer le pôle négatif du cordon

d’alimentation.

• To verify the polarity before connection, plug in the power supply with no load and

check the output with a voltmeter.

• Pour vérifier la polarité avant la connexion, brancher l’alimentation hors charge et

mesurer sa sortie avec un voltmètre.

MP 101 Series • MP 101 Series Rear Panels 4

ATTENTION:

• The length of the exposed (stripped) wires is important. The ideal length is

3/16inch (5mm). Any longer and the exposed wires may touch, causing a short

circuit between them. Any shorter and the wires can be easily pulled out even if

tightly fastened by the captive screws.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont trop longs, les

câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont trop

courts, ils peuvent être tirés facilement, même s’ils sont correctement serrés par les

borniers à vis.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling

spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation

dans les espaces d’aération ou dans les cavités murales.

• Remote power is intended for indoors use only. No part of a network that uses

remote power can be routed outdoors.

• L’alimentation à distance est exclusivement réservée à un usage en intérieur. Un

réseau utilisant une alimentation à distance ne peut pas être routé en extérieur.

Power LED (MP 101 only) (see figure1 on page2) — This LED lights green to

indicate that the unit is receiving power.

Remote Connection

Remote — An optional 3-pin, captive screw connector allows a wall mounted audio

controller or MediaLink product to remotely control volume and mute levels for the

MP101 unit (see Remote Control on page7).

Mic Input (Microphone Level)

Mic Input (MP 101 only) — A 3-pin, captive screw connector for a standard

condenser microphone connection.

Tip

Slee

Unbalanced Input

(high impedance)

Tip

Sleeve

Ring

Balanced Input

(high impedance)

(5 mm) MAX

Captive Screw

Connector stripping

3/16"

Figure 3. Audio Wiring Input

ATTENTION:

• For unbalanced audio, ensure that the Phantom power switch is set to the OFF

position.

• Pour l’audio asymétrique, assurez-vous que le switch d’alimentation fantôme

est inactif.

MP 101 Series • MP 101 Series Rear Panels 5

Audio Output (Line Level)

Line Output — A 3-pin, captive screw connector outputs to audio mixers, amps

switchers, or other non-microphone audio equipment.

Unbalanced Output

(high impedance)

Tip

Sleeve

NO Ground Here

CAUTION

For unbalanced audio, connect the sleeve(s)

to the ground. DO NOT connect the sleeve(s)

to the negative (-) contact.

(5 mm) MAX

Captive Screw

Connector stripping

3/16"

Tip

Slee

Ring

Balanced Output

Figure 4. Audio Wiring Output

ATTENTION:

• For unbalanced audio, connect the sleeve(s) to the ground. DO NOT connect

the sleeves to the negative (-) contact.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS

connecter les manchons aux contacts négatifs (–).

Low Cut Filter Switch

Low Cut filter switch (MP 101 AAP and MP 101 D) — Provides low cut filtering to

remove wind and “table rumble” noise.

Phantom Power

Phantom Power (MP 101 AAP and MP 101 D) — Provides switchable 48 volt

phantom power for condenser microphone.

MP 101 Series • MP 101 6

MP 101

The Extron MP 101 is a high performance, microphone to line level audio preamplifier.

Topics covered in the section are:

• Front Panel Features • Adjusting the MP 101

• Mounting the MP 101

Front Panel Features

MIC GAIN

(dB)

25 72

LOW CUT PHANTOM

OFF

MP 101

11223344

Power LED — This LED lights green to indicate

that the unit is receiving power.

Mic Gain — A recessed, adjustable

potentiometer defines the amount of input

signal (between 25 and 72 dB) allowed into the

preamp.

Low Cut filter switch — Provides switchable

low cut filtering to remove wind and “table

rumble” noise.

Phantom power switch — Provides

switchable 48 volt phantom power for condenser

microphone

Figure 5. Front Panel

Mounting the MP 101

There are many optional accessories for mounting the MP 101 (see accessories on

the MP101 page of the Extron website). The following Underwriters Laboratories (UL)

guidelines pertain to the safe installation of the MP 101 in a rack.

UL Rack Mounting Guidelines

1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment can be greater

than room ambient temperature. Therefore, install the unit in an environment compatible

with the maximum ambient temperature (Tma = +122°F, +50°C) specified by Extron.

2. Reduced air flow — Install the equipment in a rack so that the amount of air flow

required for safe operation of the equipment is not compromised.

3. Mechanical loading — Mount the equipment in the rack so that a hazardous

condition is not achieved due to uneven mechanical loading.

4. Circuit overloading — Connect the equipment to the supply circuit and consider the

effect that circuit overloading might have on overcurrent protection and supply wiring.

Appropriate consideration of equipment nameplate ratings should be used when

addressing this concern.

5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted

equipment. Pay particular attention to supply connections other than direct connections

to the branch circuit (for example: use of power strips).

MP 101 Series • MP 101 7

Adjusting the MP 101

After the MP 101 has been properly mounted and connected, do the following to adjust it:

1. If using a condenser microphone, set the Phantom power switch to the ON position.

If using a dynamic microphone, set the Phantom power switch to the OFF position.

2. When using the microphone for voice audio, flip the Low Cut switch to ON to reduce

wind and “table rumble” noise.

When using the microphone for music audio, flip the Low Cut switch to OFF to

preserve the optimum sound quality.

3. Set the Mic Gain potentiometer by saying a few words into the microphone and

adjusting for the maximum sound level that is free of distortion.

NOTE: If there is a remote control connection, unplug it while adjusting the Mic Gain

potentiometer. Replace the remote control when finished.

If there is minimal distortion, but greater volume is required, turn the Mic Gain potentiometer

clockwise (towards the 75 dB mark) to increase the volume, but not past the point where

distortion occurs.

Remote Control

The wiring and control options described below pertain to all models in the MP 101 series.

Remote Connector Wiring

As shown below, Pin 1 is 10 VDC reference voltage. Pin 2 is volume control DC voltage;

range is 0 to 10 V, where 0 V is mute and 10 V provides maximum volume. Pin 3 is ground.

NOTE: All nominal levels are at ±10%.

REMOTE

10V

VOL/MUTE

123

GND

10K

MAX

POWER

12V

0.3A MAX

MIC

INPUT

REMOTE

VOL/MUTE

MP 101

MIC TO LINE

PREAMPLIFIER

10V

LINE

OUTPUT

MUTE

Figure 6. Remote Connector Wiring

Remote Control Options

The MP 101 has three remote control options:

1. The Extron VCM 110 AAP volume/mute controller, VCM 200 Series volume/mute

controller, VC 50 volume controller, MLC 55 RS VC, and MLC 64 RS VC D use a 10 k

ohm potentiometer as the main method for controlling volume levels.

2. The Extron MLA-VC10 Plus converts RS-232 serial command to 0 to 10 V variable DC

for volume control.

3. Generic volume/mute controllers are standard 10 k ohm potentiometers.

MP 101 Series • MP 101 APP 8

MP 101 AAP

The Extron MP 101 AAP is a high performance microphone to line level audio preamplifier.

This model is a two-space MP 101 AAP in black. Topics covered in this section are:

• Front Panel Features • Mounting the MP 101

• Adjusting the MP 101 AAP • Remote Control

Front Panel Features

112

Figure 7. Front Panel MP 101 APP

XLR mic input — Use an XLR connector or a

3-pin

Female

standard microphone connection (see the image on

the right for connector pin out information).

Mic Gain — A recessed, adjustable potentiometer

defines the amount of input signal (between 25 and

72 dB) allowed into the preamp.

This potentiometer is covered by a plastic cap to avoid tampering. To adjust the

potentiometer, use a small screwdriver to remove the covering, make adjustments, then

replace the cap.

Active and Mute LEDs — The active LED lights green to indicate active sound. The

mute LED lights red to indicate mute.

Mute button — Toggles between active sound and mute (indicated by its LEDs).

When used with an optional Extron VCM 110 AAP controller, the two controllers are

synchronized.

MP 101 Series • MP 101 APP 9

Adjusting the MP 101 AAP

Most adjustment options for the MP 101 AAP are located on its rear panel (see MP 101

Series Rear Panels on page2). Therefore, you must perform these adjustments prior

to final mounting into a wall or a piece of furniture.

To adjust the MP 101 AAP, do the following:

1. If using a condenser microphone, flip the Phantom power switch to the ON position.

If using a dynamic microphone, flip the Phantom power switch to the OFF position.

2. When using the microphone for voice audio, flip the Low Cut switch to ON to reduce

wind and “table rumble” noise.

When using the microphone for music audio, flip the Low Cut switch to OFF to

preserve the optimum sound quality.

3. Set the Mic Gain potentiometer by saying a few words into the microphone and

adjusting for the maximum sound level that is free of distortion.

NOTE: If there is a remote control connection, unplug it while adjusting the Mic

Gain potentiometer. Replace the remote control when finished.

4. If there is minimal distortion, but greater volume is required, turn the Mic Gain

potentiometer clockwise (towards the 75 dB mark) to increase the volume, but not past

the point where distortion occurs.

Mounting the MP 101 AAP

The MP 101 AAP must be attached to a device faceplate or AAP wallplate and then cabled

before you can test and perform the final mount (installation into a wall or piece of furniture).

NOTE: Before mounting, the MP 101 AAP should be tested to verify that its

connections and settings are correct.

To mount the MP 101 AAP into a device faceplate or AAP wallplate, do the following:

1. Before any cables are attached, insert the MP 101 AAP standoffs through the holes in

the device faceplate or AAP wallplate.

2. Secure all cables and connections into the rear connectors of the MP 101 AAP.

3. Using the provided #4-40 nuts and captive washers, secure the preamplifier to the

faceplate or wallplate, as shown below.

MP 101 Series • MP 101 APP 10

Extron

MP 101 AAP

MIC to Line

Preamplifier

Installation Cable

Cable

Clamp

Screws or Nails

Wall Stud

Extron

AAP 102

#4-40 Nut w/ Captive

Washer

MIC

MLP 101 AAP

MUT E

ACTI VE

Figure 8. Mounting the MP 101 APP

4. Repeat steps 1 through 3 to mount any other AAPs. Cover any openings in the

faceplate with blank plates (provided).

5. If it was not done previously, adjust the MP 101 AAP from its rear panel (see Adjusting

the MP 101 AAP on the previous page for detailed instructions).

6. Pretest the MP 101 AAP before final mounting of the faceplate.

7. Perform the final mount by attaching the cabled device faceplate or AAP wallplate into

a wall or piece of furniture. For detailed installation information, refer to the installation

guide shipped with the faceplate.

Remote Control

The wiring and control options described below pertain to all models in the MP 101 series.

Remote Connector Wiring

Pin 1 is 10 VDC reference voltage. Pin 2 is volume control

REMOTE

10V

VOL/MUTE

123

GND

10K

MIN

MUTE

DC voltage; range is 0 to 10 V, where 0 V is mute and 10 V

provides maximum volume. Pin 3 is ground.

NOTE: All nominal levels are at ±10%.

MP 101 Series • MP 101 APP 11

Remote Control Options

The MP 101 AAP has three remote control options:

1. The Extron VCM 110 AAP volume/mute controller, VCM 200 Series volume/mute

controller, VC 50 volume controller, MLC 55 RS VC, and MLC 64 RS VC D and VC 50

volume controller use a 10 k ohm potentiometer as the main method for controlling

volume levels.

The VCM 110 AAP mute button overrides the mute button of the MP 101 D.

2. The Extron MLA-VC10 Plus converts RS-232 serial command to 0 to 10 volt variable

DC for volume control.

3. Generic volume/mute controllers are standard 10 k ohm potentiometers.

MP 101 Series • MP 101 D 12

MP 101 D

The Extron MP 101 D provides the same features as the other MP 101 models in a

convenient, Decorator-style wallplate. Like the MP 101 and MP 101 AAP, this mic to line

preamplifier can be remotely controlled via a VCM volume/mute control module.

Topics covered in this section are:

• Front Panel Features • Mounting the MP 101 D

• Remote Control

Front Panel Features

Active LED — This LED lights green to indicate that

the unit is receiving power.

Mute LED — This LED lights red to indicate mute.

Mic Gain — A recessed, adjustable potentiometer

defines the amount of input signal (between 25 and

72dB) allowed into the preamp.

This potentiometer is covered by a plastic cap to

avoid tampering. To adjust the potentiometer, use

a small screwdriver to remove the covering, make

adjustments, then replace the cap.

XLR mic input — An XLR connector for a standard

microphone connection.

3-pin

Female

Figure 9. Front Panel MP 101 D

Adjusting the MP 101 D

Adjustment options for the MP 101 D are located on its rear panel (see Front Panel

Features). Therefore, you must perform these adjustments before mounting into a wall.

To adjust the MP 101 D, do the following:

1. If using a condenser microphone, set the Phantom power switch to the ON position.

If using a dynamic microphone, set the Phantom power switch to the OFF position.

2. When using the microphone for voice audio, flip the Low Cut switch to ON to reduce

wind and “table rumble” noise.

When using the microphone for music audio, set the Low Cut switch to OFF to

preserve the optimum sound quality.

MIC IN

ACTIVE

MUTE

MP 101 Series • MP 101 D 13

3. Set the Mic Gain potentiometer by saying a few words into the microphone and

adjusting for the maximum sound level that is free of distortion.

NOTE: If there is a remote control connection, unplug it while adjusting the Mic

Gain potentiometer. Replace the remote control when finished.

If there is minimal distortion, but greater volume is required, turn the Mic Gain

potentiometer clockwise (towards the 75 dB mark) to increase the volume, but not past

the point where distortion occurs.

Mounting the MP 101 D

The MP 101 D provides the same features as the other MP 101 models in a convenient,

Decorator-style wallplate.

NOTE: Before mounting, the MP 101 D should be tested to verify that its connections

and settings are correct.

To mount the MP 101 D into a Decorator-style faceplate, do the following:

1. Secure all cables and connections onto the MP 101 D.

2. If it was not done previously, adjust the MP 101 D from its rear panel (see Adjusting

the MP 101 D on the previous page for detailed instructions).

3. Place the MP 101 D through the opening in the wall or furniture and into the wall box.

Take care not to damage the output cables, which fit behind the preamplifier at the back

of the wall box.

4. Attach the Decorator-style wallplate to the MP 101 D, as shown below.

all opening

is flush with

edge of box.

Wall Box

Decorator Style

Faceplate

Extron

MP 101 D

Mic to Line

Preamplifier

MIC IN

ACTIVE

MUTE

Figure 10. Mounting the MP 101 D

5. Pretest the MP 101 D before performing the final mount in step 6.

6. Perform the final mount by attaching the cabled MP 101 D and Decorator-style

faceplate into a wall. For detailed installation information, refer to the installation guide

shipped with the Decorator-style faceplate.

MP 101 Series • MP 101 D 14

Remote Control

Remote Connector Wiring

Pin 1 is 10 VDC reference voltage. Pin 2 is volume control

REMOTE

10V

VOL/MUTE

123

GND

10K

MIN

MUTE

DC voltage; range is 0 to 10 V, where 0 V is mute and

10 V provides maximum volume. Pin 3 is ground.

NOTE: All nominal levels are at ±10%.

Remote Control Options

The MP 101 D has three remote control options:

1. The Extron VCM 110 AAP volume/mute controller, VCM 200 Series volume/mute

controller, VC 50 volume controller, MLC 55 RS VC, and MLC 64 RS VC D and VC

50 volume controller use a 10 k ohm potentiometer as the main method for controlling

volume levels.

The VCM 110 AAP mute button overrides the mute button of the MP 101 AAP.

2. The Extron MLA-VC10 Plus converts RS-232 serial command to 0 to 10 volt variable

DC for volume control.

3. Generic volume/mute controllers are standard 10 k ohm potentiometers.

Page is loading ...

Extron electronics MP 101 D User manual

Brand: Extron electronics

Model: MP 101 D

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Extron electronics MP 101 D Manuel utilisateur

Extron electronics MP 101 D User manual

This manual is also suitable for

Extron electronics MP 101 D User manual

in other languages

Related papers

Other documents