Page is loading ...
C576U 16” Repair Manual(Electronic)
Date: 2018/12/ V1.0
目錄
1-1-1. 機台全圖
1-2-1. 面板圖
1-3-1. 零件位置圖-電子表組
1-3-2. 零件位置圖
1-3-3. 零件位置圖
1-4-1. 電子方塊圖
1-4-2. 接線示意圖
1-5-1. 接線圖-電子表組
1-5-2. 接線圖-電子表組
1-5-3. 接線圖-驅動器組
1-5-4. 按鍵開關整組說明
1-5-5. 接線圖-AV 板
1-5-6. 接線圖-節能小板
1-5-7. 接線圖-
電源板
1-6-1. 信號燈說明-驅動器組
1-7-1. 電子類規格表
2-1-1. 電子類故障排除對照表
3-1-1. 故障排除-無法開機
3-2-1. 故障排除-無 Stride/min 值顯示
3-3-1. 故障排除-踩踏機台,無任何阻力
3-3-2. 故障排除-阻力電壓太輕或太重
3-4-1. 故障排除-無線心跳動作不良
3-5-1. 故障排除-HTR 心跳不良
3-6-1. 故障排除-按鍵不良-扶手
LENGTH, HEIGHT <▲> , <▼>
3-6-2. 故障排除-按鍵不良-<Power>鍵
3-6-3. 故障排除-風扇動作不良
3-7-1. 故障排除 ERROR_8_1_
3-7-2. 故障排除 ERROR_8_2_
3-8-1. 故障排除-
有線網路不良
3-8-2. 故障排除-
無線網路不良
3-8-3. 故障排除-
TV 電視不良
3-8-4. 故障排除-
顯示面板不良
3-8-5. 故障排除-USB 小
板不良
3-8-6. 故障排.除-
藍芽功能不良
3-8-7. 故障排除-
NFC 功能不良
3-8-8. 故障排除-
影音沒有聲音
3-9-1. 其他說明-錯誤訊息一覽表
3-10-1. 其他說明-USB 小板說明
3-11-1. 其他說明-
機型小板說明
4-1-1. 檢查及量測-電磁鐵斷路檢測
4-1-2. 檢查及量測- Speed sensor 檢測
4-1-3. 檢查及量測-驅動板通訊狀況檢測
1-1.Product picture
1-1-1
1-2.Displays-C576R 16 “
1-2-1
1-3. Component placement - C576R 16”
Display
1-3-1
HTR Board
Control board
TV board
Main board
USB board
EUP<Power> key board
Ear jack board
NFC board
Bridge board for Blue teeth
1-3.Component placement - C576R 16” frame
1-3-2
MI drive board
Model no. board
Electro-magnet
HTR bridge board
SA EUP Board
Filter
1-3.Component placement - C576R 16” frame
1-3-3
Speed Sensor
Filter
Power board
Electro-magnet
HTR, Handle-keys bridge board
1-4.Block diagram- C576R 16”
1-4-1
Control board
MI Drive Board
Filter
NFC bridge board
Fan
HRC board
USB board
EUP
Board
Breaker
/Switch
<Power>
EUP Key board
耳機小板
AV board
Main board
TV board
TV Cable
WIFI Antenna
Blue teeth
HTR Board
NFC Antenna
Rocker board
RESISTANCE (L)
RESISTANCE (R)
Electro-magnet
Speed sensor
Power
board
Model no. board
HTR
Bridge board
HTR
Bridge board
HTR Plate(L)
HTR Plate(R)
Touch Screen sets
1-4.Wiring schematic- C576R 16”
1-4-2
<Power> key
1-5.wiring connection- C576R 16” Console
1-5-1
To HTR board
To Drive
board
TO Fan
To
USB board
To
polar board
To
Rocker board
T
o
(
handle
R
esistance key)
To
USB board
To EUP<Power>key
To SA WELL board
To mother board
To control board
To TV Coble
T
o mother board
To TFT Display
To TFT inverter
To Earphone jack
To TFT display
To AV board
To TV board
To AV board
To blue
-
teeth bridge board
To AV board
To
NFC
bridge board
1-5.wiring connection C576R -16” Console
1-5-2
To drive board & Power keyboard
To mother board
To control board
To NFC bridge board
To mother board
To mother board &
control
board
To control board
1-5. Wiring connection - C576R 16” Drive board
1-5-3
To Alternator
TO Model no. board
To power board
To EUP<Power> key
& control board
To Speed sensor
To EUP
1-5.Wring connection – C576 16” Resistance key
1-5-4
RESISTANCE key
To control board
Rocker board
1-5.Wiring connection – AV board
1-5-5
Appearance
Main board
CSAFE
AV board
to Main board
N
et work
1-5.Wiring connection –EUP board
1-5-6
To
(Control board，EUP<Power> key
To Drive board
From Filter
1-5.Wiring connection –Power board
1-5-7
To EUP board
To drive board
1-6.Indicator led
-
Drive board
1-6-1
LED1
-
CLK led
LED2
-
heartrate led
LED 3 –COMM
Communication led
2-1. Electronic Malfunction Troubleshooting Chart -C576R 16”
Malfunction Circumstance Inspection and testing Components to replace
No start Display is not lit; display
shows no reaction and
does not light up.
1.Inspect the switch and the fuse wire
2.Check if all the cable is well-connected
3.Check the Display set
4.Inspect or replace Eup board, power board or the
Drive Board
1. Power switch, fuse
2. Display set
3. Eup board or Power board
4. Drive Board
No RPM Start exercising on the
unit; the display shows no
reaction; RPM values on
the display do not change.
1. Check if all the bus line is well-connected
2. Check or Clean the Speed sensor
3. Is the distance between the speed sensor and
the optical disk 5mm?
4. Replace the Driver Board
1.Speed sensor
2.Drive board
No resistance Press resistance up or
down keys; resistance
values change on the
display; but there is no
resistance.
1.Display idle.. Re-start the switch.
2.Check if the RPM value is displayed.
3.Check Electromagnet wire connection.
4.Check or Replace the Drive board set
1. Drive board
Wireless
(telemetry)
heart rate
malfunction
Wireless (telemetry) heart
rate malfunction
1. Replace polar heart rate transmitter.
2. Check or replace the Polar heart rate board
3. Check if there is any interference such as the
light or the speaker.
4. Replace control board.
1.Polar heart rate transmitter
2.Polar heart rate board
3.control board
HTR heart rate
Malfunction.
HTR heart rate
Malfunction.
1.Inspect the HTR cable connection.
2.Inspect the HTR LED indicators.
3.Replace the HTR board.
1.HTR board
2.HTR sensor plate
3.HTR cable
TV function
malfunction.
Cannot watch TV. 1. Check the signal source of the TV
2. Inspect TV settings and each scan all available
TV channels
3. Replace the TV board
4. Replace the Mainboard
1.TV board
2.Mainboard
2-1-1
Fan
malfunction
Press fan key , the fan
motor does not have any
reaction.
1. Check the fan and control board.
2. Replace control board.
3. Replace the fan motor
1. Control board
2. Fan motor
ERROR
8_1,8_2
The Displays shows
ERROR 8_1, 8_2
1. Check the Wiring between Display & Drive
Board
2. Replace control board.
3. Replace the Driver Board
1. Control board
2. Drive Board
Wired Network
malfunction
Cannot Use the Wired
Networking function
1. Check the signal source of the Wired Network
2. Check the Wired Network Wiring inside the
machine
3. Check the settings of the Wired Network
4. Check or replace the Mainboard
1. Wired Network bus line
2. Mainboard
WIFI Network
malfunction
Cannot Use the WIFI
Networking function
1. Check the source signal of the WIFI Network.
2. Check the settings of the WIFI Network
3. Check the WIFI antenna and the Mainboard
1.Mainboard
2. WIFI antenna
The video does
not have any
audio
There is no audio from the
video or the TV
1. Check the earphone set.
2. Replace the TV board
3. Replace the Mainboard
1. Earphone board
2. TV board
3. Mainboard
TFT screen
Faulty.
TFT screen malfunction 1. Check All Wiring
2. Replace the Mainboard
3. Replace TFT screen set.
1.Mainboard
2.TFT screen set
Touch screen
Faulty.
Touch screen malfunction.
1. Check Touch screen board connection.
2. Replace touch screen set.
1. TFT screen set
USB board
Faulty.
Cannot read data from the
USB Flash Drive or
update the Program
1. Use a USB Flash Drive Brand specified by
SPORTSART
2. Inspect the USB board connection.
3. Replace the USB board
1.USB board
2-1-2
Malfunction Circumstance Points for inspection and testing Components to replace
Malfunction of
Bluetooth
Cannot Use the Bluetooth
function
1. Check if the Bluetooth function is enabled
2. Check the Bluetooth board Wiring
3. Replace the Bluetooth board
1.the Bluetooth board
Malfunction of
the NFC
Cannot Use the NFC
function
The NFC function is disabled for now.
2-1-3
/