Raytheon Remote FU-Tiller (dual), Type 105-304 Operating instructions

Brand: Raytheon

Model: Remote FU-Tiller (dual), Type 105-304

Type: Operating instructions

Raytheon Anschütz GmbH

Postfach 1166

D -- 24100 Kiel

Germany

Tel+49--431--3019--0

Fax+49--431--3019--501

Email [email protected]

www.raytheon --anschuetz.de

3434E/105--304.DOC012 Edition: 15 Aug 00

Revision: 22. January 2003

Revision: March 16, 2007

Remote

FU Tiller (dual)

Type 105 -- 304

Operating instructions

Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung

und

Mitteilung ihres Inhaltes nicht gestattet, soweit nicht ausdrücklich

zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz.

Copying of this document, and giving it to others and the use or

communication of the contents thereof, are forbidden without

express

authority. Offenders are liable for payment of damages.

Toute communication ou reproduction de ce document, toute

exploitation ou communication de son contenu sont interdites, sauf

autorisation expresse. Tout manquement à cette règle est illicite et

expose son auteur au versement de dommages et intérêts.

Sin nuestra expresa autorización, queda terminantemente

prohibida la

reproducción total o parcial de este documento, así como su uso

indebido y/o su exhibición o comunicación a terceros. De los

infractores

se exigirá el correspondiente resarcimiento de daños y perjuicios.

STEERING

Remote FU Tiller (dual)

CONTROL

Operating instructions

3434E/105--304.DOC012Edition: 22. January 2003

TABLE OF CONTENTS Page

1 General 1...............................................................

2 Remote FU Tiller (dual) in Steering Control System 2........................

3 Notes to operating instructions 3...........................................

4 Switching on 4..........................................................

4.1 General 4...............................................................

5 Standard operation 5.....................................................

6 Additional controls in standard operation 7..................................

6.1 Illumination control 7.....................................................

6.2 Testing 9...............................................................

6.3 Warning messages 11.....................................................

7 Faulty operation 13.......................................................

Annex: Control and display devices

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012

Edition: 15 Aug 00

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 15 Aug 00

1 General

The remote FU tiller (dual) is used on the bridge to steer a course and is installed at the vessel

control panel or navigating stand (

F OLLOW U P). Two remote FU tillers are needed at all

times to act as dual tillers for twin rudder equipment with separate rudder blade control.

Either of two operating modes – SYNCHRONOUS or INDEPENDENT -- may be selected.

The scale graduation is ± 35 ° , as standardand the control knob deflection angle is ± 60 °. The

control knob is slightly engaged when it is at the mechanical zero position. The scale is

illuminated.

In order to change the rudder angle (e.g. to starboard) turn the control knob clockwise.

The effect on steering is similar to that of a hand wheel.

Operating instructions

These operating instructions contain every operational procedure as well as information about

behaviour when alarms occur. Such alarms are indicated on the digital display units and also by

means of flashing LEDs and audible alarm signals.

Service manual

In addition to the operating manual, there is also a service manual. It contains the following:

-- Information relating to installation and initial start-up

-- Information relating to maintenance and repairs, and

-- a description of the tiller

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

2 Remote FU Tiller (dual) in Steering Control system

Remote FU tillers (dual) are bus users on the user device bus (BG bus)

on the NP 2000

autopilot control transmitter within a secondary steering system.

The remote FU tiller (dual) is activated by setting the steering mode selector either to the

REMOTE or the AUTO/REMOTE setting (see figure). The bus transfers the control signals,

and the NP2000 Autopilot Control Unit converts these into analogue control signals for the FU

amplifier.

The control point and operating mode (SYNCHRONOUS or INDEPENDENT) can be selected

on site. The selection is made according to the “Take Over” principle, i.e. only one control point

is active for SYNCHRONOUS operation, and both are active for INDEPENDENT operation.

A total of 15 bus users can be connected.

Port wing

BG--Bus

NP 2000 Autopilot

FU Tiller Dual 1

(rudder 1)

FU--Tiller Dual 2

(rudder 2)

Steering

mode selector

Remote

Max. 15 bus users

168.5

FU amplifier

analogue

set rudder

value signal

specific to Raytheon Marine

Rudder 1 Rudder 2

Auto/Remote

Remote FU Tiller (dual) in Steering Control system

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 15 Aug 00

3 Notes to operating instructions

The system operates interactively (i.e. an action causes a reaction).

Each operating procedure shown must be completed step by step. Where necessary and in the

relevant sections, we have added useful supplementary notes alongside the illustrations

(symbols).

We recommend that you fold out the appendix page since it contains an illustration of all the

controls and indications.

Explanation of the symbols used.

press a key

LED off

LED on

LED flashing

audible signal on

audible signal off

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

4 Switching on

When the full rudder control system is switched on, the remote FU tillers (dual) are also

ready for operation in REMOTE or in AUTO/REMOTE mode.

4.1 General

indications Comments

Notes

red

For example:

The display is indicating the c urrent rudder

angle in ° , the relevant LED is illuminated.

If the final decimal point of the indicated figure

is illuminated, this means that an additional

0.5 ° is being indicated. In the example: 10,5°

Rudder position is indicated by illuminating the

relevant LED (PORT is red, STBD is green).

Both LEDs remain unlit when the rudder posi-

tion is 0 °

It is possible to have two different system configurations.

a) The FU tiller can only be used in REMOTE operating mode.

b) In AUTO/REMOTE operation mode, it is possible to switch between FU

tiller and autopilot operation without activating the steering mode selector.

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 15 Aug 00

5 Standard operation

Indications Comments

Notes

¡ Tiller in Standby

Version a:

Synchronous

Active

Standby

yellow

Independent

Set steering mode selector to REMOTE

After switching to REMOTE the

rudder is s teered manually by

means of the hand wheel until a

tiller is activated.

The ‘standby’ LED beside the

Active/Standby key is illuminated

Version b:

Active

Standby

yellow

Synchronous

Independent

Steering mode selector is set to

AUTO/REMOTE

After switching to AUTO/REMOTE

The rudder is steered manually by

means of the hand wheel until a

tiller is activated.

The ‘standby’ LED beside the

Active/Standby key is illuminated

Active

Standby

Active

Standby

red

For example:

green

Tiller Steering

Autopilot:

Synchronous

Independent

green

Press the Active/Standby key

An audible signal sounds when the switch is

made

The ‘Synchronous’ LED is illuminated green.

When the tiller is activated

‘Synchronous’ operation is always

selected.

The active tiller controls both

rudders.

The ‘Active’ L ED beside the key is illuminated

green

The line of text on the autopilot control unit

indicates manual steering.

Turn the knob to set the required rudder angle.

This adjusts both rudders.

The display unit indicates the actual rudder

angle in ° and the relevant LED is illuminated.



Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

Indications Comments

Notes

¢ Activating the tiller for ‘Independent’ operation

Active

Standby

red

green

Tiller Steering

Autopilot:

Synchronous

Independent

green

red

Rudder 1

Rudder

For example:

Once the procedure © has been executed:

press the key

An audible signal sounds when the switch is

made.

The ‘Independent’ LED is illuminated green.

Both the tillers are now active.

The ‘Active’ LED beside the key continues to

be illuminated green.

The line of text on the autopilot control unit

continues to indicate manual steering.

Turn the knob for Tiller 1 to the required rudder

angle for rudder 1.

Turn the knob for Tiller 2 to the required rudder

angle for rudder 2.

The display unit indicates the actual rudder

angle in ° and the relevant LED is illuminated.

£ Switching from ‘Independent’ to ‘Synchronous’ operating mode

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 15 Aug 00

Indications Comments

Notes

Active

Standby

green

Tiller Steering

Autopilot:

Synchronous

Independent

green

Active

Standby

yellow

press the key again

An audible signal sounds when the switch is

made

The tiller to which the switch has just

been made changes to

‘Synchronous’, and the second

tiller changes automatically from

‘Active’ to ‘Standby’.

The ‘Synchronous’ LED is illuminated green.

The second rudder adopts the rudder

position of the synchronous tiller that

has just been activated.

The ‘Active’ L ED beside the key for the tiller

that has been switched on continues to be

illuminated green .

The ‘Standby’ LED on the other tiller is

illuminated yellow.

The line of text on the autopilot control unit

continues to indicate manual steering.

Continue as for procedure ¢



¤ Deactivating the tiller

Active

Standby

yellow

Heading

Control

Autopilot:

other tiller

Active

Standby

yellow

1. Switch the steering mode selector to main

FU steering system or NFU

2. Return control system to autopilot:

Activate a function key (e.g. HEADING

CONTROL) on the autopilot

(see system configuration)

3. activate another tiller

The ‘Standby’ L ED beside the deactivated tiller

is illuminated yellow.

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

6 Additional operation in standard operation

6.1 Illumination control

Indications Comments

Notes

Increases the brightness on all LEDs and Indications.

Decreases the brightness on all LEDs and Indications.

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 22. January 2003

6.2 Testing

Indications Comments

Notes

simultaneous

For

example:

For

example:

For

example:

For

example:

Locations:

Pn = Port Wing

Sn = Starboard Wing

br = Bridge (1)

bb = Bridge (2)

Automatic test cycle lasting approx. 30s.

Approx. 2 second check of

-- 7 segment display

-- Audible signal (twice)

-- LEDs to maximum brilliance

-- Key illumination to maximum brilliance

The following indications are then tested:

-- Tiller type Dual FU PORT (dP) and

Dual FU STBD (dS)

-- Bridge allocation

For example: Tiller on bridge 1 (b1)

-- Group to which it belongs

Forexample:Group1(G1)

-- Rudder scale in two s teps

-- Indication (rS)

-- Rudder scale value

For example: 35 °

-- Software version in two steps

-- E

-- 00.

-- 0 0

-- Indication of installation--position (also in

case of external control)

Fr = External control possible

(External control must not be

installed)

Po = Position

---- = not already adjusted



Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

Indications Comments

Notes

For

example:

-- The DP address in two steps

-- Bus user address (Ad)

-- Va l u e e . g . 5

-- Current status of bus termination

e.g. RS485 interface is not terminated

(’t1’ ≙ is terminated)

For

example:

-- The EPROM checksum in three steps,

e.g. A3 E6

-- Check sum (CH)

-- upper hexadecimal value

-- lower hexadecimal value

When the test has ended the display automati-

cally reverts to indicating the rudder position

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: 15 Aug 00

6.3 Warning messages

Warning messages occur if the remote FU tiller (dual) is activated

without previously activating tiller control, which means that steering

control is ineffective from this tiller.

Indications Comments

Notes

¡ Steering mode selector to AUTO

Active

Standby

Version a:

Version b:

Active

Standby

yellow

Steering mode selector is set to ‘Auto’

Version a (see section 4):

Neither LED (ACTIVE or STANDBY) is lit.

Version b (see section 4):

The STANDBY LED is illuminated

When the tiller is moved

a pulsed audible warning signal (5 separate

tones) sounds.



Active

Standby

Steering mode selector is set to ‘Remote.

The STANDBY LED is illuminated.

When the tiller is moved

a pulsed audible warning signal (5 separate

tones) sounds.

¢ Steering mode selector to NFU

Active

Standby

Steering mode selector is set to ‘NFU’

Neither LED (ACTIVE or STANDBY) is lit.

When the tiller is moved

a pulsed audible warning signal (5 separate

tones) sounds.

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

Indications Comments

Notes

£ Steering mode selector to FU

Active

Standby

Steering mode selector is set to ‘FU’

Neither LED (ACTIVE or STANDBY) is lit

When the tiller is moved

a pulsed audible warning signal (5 separate

tones) sounds.

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012Edition: March 16, 2007

7 Faulty operation

Behaviour when alarms occur:

-- When an alarm occurs:

-- Acknowledge alarm by pressing The audible alarm stops, the LED is

illuminated.

The light remains on permanently

until the fault is rectified

-- Steering mode selector to AUTO

No Indication Meaning Likely

cause

Effect on

operation

Measures to take

1 BG bus error

-- Short circuit

-- Faulty cable

-- Faulty tiller

The tiller cannot be

used

-- Switch steering mode selector from

‘Auto’ or ‘Remote’ to ‘FU’ or NFU

-- Check the cable connection

-- Disconnect the faulty device from

the bus

2 Steering failure Steering control

faulty

Reference para-

meters for set rud-

der turning rate not

set correctly

The tiller cannot be

used, if the rudder

does not follow the

set values

The tiller can be

used if it is only the

monitoring para-

meter that is incor-

rectly adapted

-- Set steering mode selector to

MANUAL

-- Inform Raytheon Anschütz

-- Set steering mode selector to

MANUAL

-- Adapt the parameter

check parameter RdSpeed

(adjustable at the Autopilot)**

-- Inform Raytheon Anschütz

3 Tiller fault Defect in bus tiller The tiller cannot be

used

-- Switch steering mode selector from

‘Auto’ or ‘Remote’ to ‘FU’ or NFU

-- Change tiller control point

4 Configuration

fault

-- Incorrect value

-- Values outside

valid range

Values not

adopted, although

bus tiller operation

is not defective

Check the configuration

(see service manual)

specific to Raytheon Anschütz

**) Rudderturning rate not correct adjusted (parameter setting “1” at the Autopilot meets a rate of 1°/s). If the

error E2 occurs an adjustment of either “0” or a higher setting than “1” for RdSpeed (Rudder Speed) must be

selected → System configuration, Operator Unit Autopilot.

and

red

Remote FU Tiller (dual)

Operating instructions

3434E/105--304.DOC012 Edition: 15 Aug 00

No Indication Meaning Likely

cause

Effect on

operation

Measures to take

1*)

For Dual Follow-up

devices the second

device for Indepen-

dent operation is

missing

-- The second

device is

incorrectly

configured

-- The second

device is not

connected

Independent oper-

ation not possible

Only synchronous steering

possible!

Check bus connection to second

device

EEPROM

faulty

Faulty EEPROM The tiller cannot be

used

-- Switch steering mode selector from

‘Auto’ or ‘Remote’ to ‘FU’ or NFU

-- Change tiller control point

-- Inform Raytheon Anschütz

Unknown tiller type Hardware fault Tiller not operating -- Switch steering mode selector from

‘Auto’ or ‘Remote’ to ‘FU’ or NFU

-- Change tiller control point

-- Inform Raytheon Anschütz

No tiller telegrams -- No bus

connection

-- Faulty device

The tiller cannot be

used

-- Switch steering mode selector from

‘Auto’ or ‘Remote’ to ‘FU’ or NFU

-- Change tiller control point

-- Check bus connection

(check data cable)

-- Inform Raytheon Anschütz

1*) Once alarms E2 and E5 have been acknowledged the display reverts to standard

rudder position display, so that the rudder position can continue to be adjusted.

The luminous alarm diode changes from flashing to permanently lit and remains

illuminated until the fault has been rectified.

The error code can be retrieved by pressing the alarm key at any time while the

displayisactive.

STEERING

CONTROL

Remote FU Tiller (dual)

Operating instructions

Annex1

3434E/105--304.DOC012Edition: 15 Aug 00

FU Tiller

Control and display devices

PORT LED

(red)

STBD LED

(green)

7 segment indicator

actual indication in °

current parameter

Alarms

Alarm signal

and acknowledgement

(red LED)

set rudder in °

PORT figures in red

STBD figures in green

control knob:

Brightness control

infinitely variable brightness control

Testing

a check is made of

-- the 7 segment indicator

-- the audible alarm

-- the LEDs to maximum brightness

-- Key illumination to

maximum brightness

-- current parameters

Tiller activation

‘Tiller active’ LED

(green)

‘Tiller Standby’ LED

(yellow)

-- D u a l --

Indicator for

synchronous operation and

LED indicator (green)

Indicator for

Independent operation and

LED indicator (green)

Switch from:

-- synchronous to

Independent

-- Independent to

Synchronous

STEERING

CONTROL

Tiller group for remote and override operation

3434E/105--304.DOC022Edition: 22. January 2003

Short-form operating instructions

Tiller type

Steering

mode selector

Activation and operation Indication Deactivation Comments

Remote

NFU Tiller

Type 105 -- 300

Active

Standby

yellow

Active

Standby

green

see description no. 3430E/105--300.DOC012

Remote

FU Tiller

Type 105 -- 301

Active

Standby

yellow

Active

Standby

green

10° STBD

e.g.

1. Switch steering mode selector

to main FU steering system

or NFU

see description no. 3431E/105--301.DOC012

Remote FU Tiller

(Dual)

Type 105 -- 304

Two devices required

Version b:

Active

Standby

yellow

Active

Standby

green

Synchronous

green

Independent

green

Synchronous

green

Both rudders One rudder only Both rudders

red

10° PORT

Rudder position 0°

Tiller Steering

Autopilot:

red

10,5° PORT

e.g.

2. control system returned to

autopilot: activate a function

key (e.g. HEADING

CONTROL) on the autopilot

(system configuration)

3. activate another tiller

Active

Standby

yellow

Heading

Control

utop

ot:

other tiller

er sw

AUTO/REMOTE on the steering mode

selector the rudder is steered

manually until a tiller is activated.

see description no. 3434E/105--304.DOC012

Autopilot Override

NFU Tiller

Type 105 -- 302

Standby

yellow

Active

green

1. Switch steering mode selector

to main FU steering system

or NFU

Neither LED is lit

see description no. 3432E/105--302.DOC012

Autopilot Override

FU Tiller

Type 105 -- 303

Standby

yellow

Active

green

Override

2. press the AUTO key

Steering control is taken over by

the autopilot

Auto

see description no. 3433E/105--303.DOC012

Dimming

Infinitely variable

brightness control

for all LEDs and

indicators.

Test

For example:

for FU Tiller

(dual) only

simultaneous

For

example:

Tiller type Assignment of

bridge

Group to which

it belongs

Rudder scale Software version

DP address

For

ex.:

Bus termination

For example:

Check sum

For

example:

t1 = terminated

t0 = not terminated

For

example:

Automatic testing cycle

lasting approx. 30s

-- 7 segment

-- audible signal

-- L E D s

-- key illumination

indicator

Position

f. example:

Fr=Remote control

Po=Position

Page is loading ...

Raytheon Remote FU-Tiller (dual), Type 105-304 Operating instructions

Raytheon Remote FU-Tiller (dual), Type 105-304 Operating instructions

Raytheon Remote FU-Tiller (dual), Type 105-304 Operating instructions

Related papers

Other documents