SolarEdge SE100KUS Installation guide

Disclaimers

Important Notice

Copyright©SolarEdgeInc.Allrightsreserved.

Nopartofthisdocumentmaybereproduced,storedinaretrievalsystemortransmitted,inanyformor

byanymeans,electronic,mechanical,photographic,magneticorotherwise,withoutthepriorwritten

permissionofSolarEdgeInc.

Thematerialfurnishedinthisdocumentisbelievedtobeaccurateandreliable.However,SolarEdge

assumesnoresponsibilityfortheuseofthismaterial.SolarEdgereservestherighttomakechangestothe

materialatanytimeandwithoutnotice.YoumayrefertotheSolarEdgewebsite

(https://www.solaredge.com/us/)forthemostupdatedversion.

Allcompanyandbrandproductsandservicenamesaretrademarksorregisteredtrademarksoftheir

respectiveholders.

Patentmarkingnotice:seehttps://www.solaredge.com/us/patent

ThegeneraltermsandconditionsofdeliveryofSolarEdgeshallapply.

Thecontentofthesedocumentsiscontinuallyreviewedandamended,wherenecessary.However,

discrepanciescannotbeexcluded.Noguaranteeismadeforthecompletenessofthesedocuments.

Theimagescontainedinthisdocumentareforillustrativepurposesonlyandmayvarydependingon

productmodels.

FCC Compliance

Emission Compliance

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant

topart15oftheFCCRules.Thisequipmenthasbeentestedandfoundtocomplywiththelimitsapplied

bythelocalregulations.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmful

interferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterference

toradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcan

bedeterminedbyturningtheequipmentoffandon,youareencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

lReorientorrelocatethereceivingantenna.

lIncreasetheseparationbetweentheequipmentandthereceiver.

lConnecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected.

lConsultthedealeroranexperiencedradio/TVtechnicianforhelp.

Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancemayvoidthe

user’sauthoritytooperatetheequipment.

Disclaimers

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

1

Contents

Disclaimers 1

ImportantNotice 1

FCCCompliance 1

EmissionCompliance 1

Support and Contact Information 5

HANDLING AND SAFETY INSTRUCTIONS 7

SafetySymbolsInformation 7

IMPORTANTINVERTERSAFETYINSTRUCTIONS 7

Chapter 1: Introducing the SolarEdge Power Harvesting System 10

PowerOptimiser 10

ThreePhaseInverterwithSynergyTechnology 11

MonitoringPlatform 12

SupportedACGrids 12

InstallationProcedure 12

InstallationEquipmentList 13

Chapter 2: Installing the Power Optimisers 14

Safety 14

PackageContents 15

InstallationGuidelines 15

Step1:MountingandGroundingthePowerOptimizers 16

Step2:ConnectingaPVModuletoaPowerOptimiser 19

Step3:ConnectingPowerOptimisersinStrings 19

Step4:VerifyingProperPowerOptimiserConnection 21

Chapter 3: Installing the Primary and Secondary Unit(s) 22

PrimaryUnitPackageContents 22

SecondaryUnitPackageContents 22

IdentifyingtheUnits 22

PrimaryUnitInterface 22

ConnectionUnitInterface 26

SecondaryUnitInterface 27

OpeningConduitDrillGuides 27

MountingandConnectingthePrimaryandSecondaryUnit(s) 29

Chapter 4: Connecting the AC and DC Strings to the Connection Unit 37

ConnectingtheACGridtotheConnectionUnit 37

ConnectingtheACGridandGroundingtotheConnectionUnit 37

ConnectingtheStringstotheConnectionUnit 39

SettingtheInvertertoSupport208V3-wireGrid 41

Chapter 5: Activating, Commissioning and Configuring the System Using the Inverter SetApp 42

Step1:ActivatingtheInstallation 42

Step2:CommissioningandConfiguringtheInstallation 43

SettingCountryandLanguage 43

Pairing 43

Communication 44

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

2

PowerControl 44

DeviceManager 45

Maintenance 45

Information 46

Step3:VerifyingProperActivationandCommissioning 47

ViewingSystemStatus 47

MainInverterStatus 47

SiteStatus 49

CommunicationStatus 51

InverterEnergyStatus 52

MeterStatus 52

ReportingandMonitoringInstallationData 54

TheMonitoringPlatform 54

CreatingLogicalandPhysicalLayoutusingInstallationInformation 55

Designer 55

MapperApplication 55

PhysicalLayoutEditor 55

UsingaPaperTemplate 56

Chapter 6: Setting Up Communication 57

CommunicationOptions 58

Ethernet 58

RS485 58

GSM 58

CommunicationConnectors 59

CommunicationBoard 60

PrimaryUnitCommunicationBoard 60

ConnectionUnitCommunicationBoard 61

RemovingtheConnectionUnitCover 61

CreatinganEthernet(LAN)Connection 61

CreatinganRS485BusConnection 65

RS485BusConfiguration 67

VerifyingtheConnection 68

Appendix A: Errors and Troubleshooting 70

IdentifyingErrors 70

PowerOptimizerTroubleshooting 72

TroubleshootingCommunication 73

TroubleshootingEthernet(LAN)Communication 73

TroubleshootingRS485Communication 73

AdditionalTroubleshooting 73

Appendix B: Mechanical Specifications 75

PrimaryUnitandConnectionUnit 75

SecondaryUnit 75

Appendix C: External Fan Maintenance and Replacement 76

FanMaintenance 76

ExternalFanReplacement 76

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

3

Appendix D: Replacing System Components 78

ReplacingthePrimaryUnit 78

ReplacingaSecondaryUnit 79

ReplacingtheConnectionUnit 80

RemovingtheConnectionUnit 80

InstallingaNewConnectionUnit 80

ConnectingtheConnectionUnittothePrimaryUnit 81

ReplacingPowerOptimisers 81

Three Phase Inverter with Synergy Technology - Technical Specifications (North America) 83

DefaultTripLimitsandTimesAccordingtoIEEE1547 85

ConnectionUnit 86

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

4

Support and Contact Information

IfyouhavetechnicalproblemsconcerningSolarEdgeproducts,pleasecontactus:

lUSAandCanada:15104983200

lWorldwide:+9720732403118

lFax:+1(530)273-2769

lEmail:ussupport@solaredge.com.

lSupportCenter:https://www.solaredge.com/us/service/support

Beforecontact,makesuretohavethefollowinginformationathand:

lModelandserialnumberoftheproductinquestion.

lTheerrorindicatedontheInverterSetAppmobileapplicationoronthemonitoringplatformorby

theLEDs,ifthereissuchanindication.

lSystemconfigurationinformation,includingthetypeandnumberofmodulesconnectedandthe

numberandlengthofstrings.

lThecommunicationmethodtotheSolarEdgeserver,ifthesiteisconnected.

lTheinvertersoftwareversionasappearsinthestatusscreen.

Support and Contact Information

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

5

Version History

lVersion1.4-December2018

lUpdatedcommunicationoptionsandmenus.

lUpdatedguidelinesforuseofextensioncabelsinpoweroptimizerinstallation.

lVersion1.3-November2018

lDeletedcableinsulationstrippingimageandstepfrom'ToconnectACfromground'

lAddedcautionaboutlugtypes.

lModifiedmaximumlugtonguethicknessto0.16"

lChanged"shrinks"to"heatshrink".

lAddedoptionformountinginverterwithoutusingalevel

lModifiedsupportedACgridsto480Vand208V(modifiedin1.2).Modifiedimage.

lModified'theoppositepolarityDCConductorsinthesameconduit'note(for480Vinvertersuse

1000ratedcablesandfor208Vinvertersuse600VDCratedcables)

lAddedstep'DisconnecttheACtotheinverterbyturningOFFthecircuitbreakersonthe

distributionpanel'inReplacingaSecondaryUnit

lSpecifications

oUpdated'RecommendedOCPDsizepergrid'

oAddedSE43.2-USvaluestoFaultcurrentcontributiontable

oDeletedDCSurgeProtectionandDCFusesonPlus&Minus

lVersion1.2-October2018

lAdditionofpossibilitytousecompatibleconnectorsfromthird-partymanufacturers

lUpdateregardinguseofextensioncablesinpoweroptimiserinstallationguidelines

lRecommendationtomountthepoweroptimiserinalocationprotectedfromdirectsunlight

lAdditionofcaution-installationinsalineenvironment

lAdditionoflinktotheDesignerwebpage

lUpdatedwarningaboutsealingunusedpoweroptimiserinputconnectors

lOutputsafevoltageis1V(±0.1V)

lChangedConnectionUnitcovertorquesizeto10.3N*m

lMountingandConnectingthePrimaryandSecondaryUnit(s)sectionandprocedure,step10,

modifiedsubstepato'Positionthecablesothatthearrowsarefacingyou'.

lVersion1.1-Editorialupdates(March2018)

lVersion1-(February2018)



-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

6

HANDLING AND SAFETY INSTRUCTIONS

Duringinstallation,testingandinspection,adherencetoallthehandlingandsafetyinstructionsis

mandatory.Failure to do so may result in injury or loss of life and damage to the equipment.

Safety Symbols Information

Thefollowingsafetysymbolsareusedinthisdocument.Familiarizeyourselfwiththesymbolsandtheir

meaningbeforeinstallingoroperatingthesystem.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly performed or adhered to, could

result in injury or loss of life. Do not proceed beyond a warning note until the indicated conditions

are fully understood and met.

AVERTISSEMENT!

Dénote un risque: il attire l'attention sur une opération qui, si elle n'est pas faite ou suivi correctement,

pourrait causer des blessures ou un danger de mort. Ne pas dépasser une telle note avant que les

conditions requises soient totallement comprises et accomplies.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if not correctly performed or adhered to, could

result in damage or destruction of the product. Do not proceed beyond a caution sign until the

indicated conditions are fully understood and met.

ATTENTION

Dénote un risque: il attire l'attention sur une opération qui, si elle n'est pas faite ou suivi correctement,

pourrait causer un dommage ou destruction de l'équipement. Ne pas dépasser une telle note avant que

les conditions requises soient totallement comprises et accomplies.

NOTE

Denotes additional information about the current subject.

IMPORTANT SAFETY FEATURE

Denotes information about safety issues.



IMPORTANTINVERTERSAFETYINSTRUCTIONS

SAVETHESEINSTRUCTIONS

WARNING!

The inverter cover must be opened only after shutting off the inverter ON/OFF switch located at the

bottom of the Primary Unit, above the Connection Unit. This disables the DC voltage inside the inverter

and opens the AC relays. Wait five minutes before opening the cover. Otherwise, there is a risk of

electric shock from energy stored in the capacitors.

AVERTISSEMENT!

Ne pas ouvrir le couvercle de l'onduleur avant d'avoir coupé l'interrupteur situé en dessous de l'onduleur.

Cela supprime les tensions CC et CA de l'onduleur. Attendre que le LCD affiche une tension sécurisée

(50V). Si l’affichage LCD n’est pas visible, attendre cinq minutes avant d’ouvrir le couvercle. Sinon, il y a

un risque de choc électrique provenant de l'énergie stockée dans le condensateur.

HANDLING AND SAFETY INSTRUCTIONS

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

7

WARNING

Before operating the inverter, ensure that the inverter is grounded properly.

AVERTISSEMENT!

Avant d'utiliser l'onduleur monophasé, est correctement mis à la terre.

WARNING!

The inverter input and output circuits are isolated from the enclosure. This system does not include an

isolation transformer and should be installed with an ungrounded PV array in accordance with the

requirements of NEC Articles 690.35 and 690.43 National Electric Code, ANSI/NFPA 70, 2011 (and

Canadian Electrical Code, Part I, for installations in Canada).

Equipment grounding is the responsibility of the installer and must be performed in accordance with all

applicable Local and National Codes.

AVERTISSEMENT!

Les circuits d’entrée et de sortie de l’onduleur sont isolés de l’enveloppe. Ce système n’inclut pas

d’isolation galvanique (transformateur) et devra être installé sans mise à la terre du champ PV et en

accord avec les articles 690.35 et 690.43 du National Electric Code (NEC), ANSI/NFPA 70, 2011 (et du

Code Electrique Canadien, Partie 1, pour les installations faites au Canada).

La mise à la terre des équipements est la responsabilité de l’installateur et doit être faite en accord avec

les toutes les règles locales et nationales applicables.

WARNING!

Opening the inverter and repairing or testing under power must be performed only by qualified service

personnel familiar with this inverter.

AVERTISSEMENT!

L’unité ne doit être ouverte que par un technicien qualifié dans le cadre de l'installation et de la

maintenance.

WARNING!

The three phase SE66.6KUS and SE100KUS inverters must be connected only to a dedicated AC

branch circuit with a maximum Overcurrent Protection Device (OCPD) of 120A or 180A respectively.

AVERTISSEMENT!

Les onduleurs triphasés SE66.6kUS et SE100kUS doivent être connectés à une ligne appareil AC

dédiée avec un appareil de protection de sur-courant (OCPD-OverCurrent Protection Device) de

maximum 120A ou 180A respectivement.

WARNING!

SafeDC complies with IEC60947-3 when installing the system with a worst case SafeDC voltage (under

fault conditions) < 120V.

The worst case voltage is defined as: Voc,max+ (String Length-1)*1V,where:

lVoc,max = Maximum Voc (at lowest temperature) of the PV module in the string (for a string with

multiple module models, use the max value)

lString Length = number of power optimisers in the string

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

8

IMPORTANTINVERTERSAFETYINSTRUCTIONS

CAUTION!

This unit must be operated according to the technical specification datasheet provided with the unit.

ATTENTION!

Cette unité doit être utilisée selon les spécifications de fonctionnement, comme décrit dans la dernière

fiche technique des spécifications.

CAUTION!

HEAVY OBJECT. To avoid muscle strain or back injury, use proper lifting techniques, and if required - a

lifting aid.

ATTENTION

Objet lourd. Pour éviter la fatigue musculaire ou des blessures au dos, utilisez des techniques de levage

appropriées et, si nécessaire - un auxiliaire de levage lors du retrait.

NOTE

If opposite polarity DC Conductors are routed in the same conduit for 480V inverters, use 1000 rated

cables and for 208V inverters use 600VDC rated cables.

NOTE

This inverter is provided with an IMI (Isolation Monitor Interrupter) for ground fault protection.

NOTE

The symbol appears at grounding points on the SolarEdge equipment. This symbol is also used in

this manual.

NOTE

ASolarEdgeinvertermaybeinstalledinasitewithagenerator,howevermustnotoperateat

thesametimeasthegenerator.

Operatinganinverterandageneratorsimultaneouslywillvoidthewarranty.SolarEdgerequires

installingaphysicalorelectronicinterlock,whichwillpreventthegeneratorandinverterfrom

operatingsimultaneously.Interlockprocurement,installation,maintenanceandsupportare

theresponsibilityoftheinstaller.Damagetotheinverterduetoincorrectinterlockinstallation

oruseofaninterlockthatisincompatiblewiththeSolarEdgesystemwillrendertheSolarEdge

warrantyinvalid.

IMPORTANT SAFETY INFORMATION

lBuilding or structures with both utility service and a PV system, complying with NEC 690.12, shall

have a permanent plaque or directory including the following wording:PHOTOVOLTAIC SYSTEM

EQUIPPED WITH RAPID SHUTDOWN. The term “PHOTOVOLTAIC” may be replaced with

“PV.” The plaque or directory shall be reflective, with all letters capitalized and having a minimum

height of 9.5mm (3/8 in.) in white on red background.

lAttention -The system status indicator shall be installed in a location in close proximity to the

system actuator, where the indication of safe shutdown can be clearly seen.

lThis rapid shutdown system is required to be provided with an actuating device or a status

indicator which shall be installed in a location accessible to first responders, or be connected to an

automatic system which initiates rapid shutdown upon the activation of a system disconnect or

activation of another type of emergency system.

lAdditionally, in a prominent location near the actuator device the end use installation shall be

provided with a permanent marking including the following wording:PHOTOVOLTAIC SYSTEM

EQUIPPED WITH RAPID SHUTDOWN. The term “PHOTOVOLTAIC” may be replaced with

“PV”. The plaque or directory shall be reflective, with all letters capitalized and having a minimum

height of 9.5mm (3/8 in.) in white on red background.

HANDLING AND SAFETY INSTRUCTIONS

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

9

Chapter 1: Introducing the SolarEdge Power

Harvesting System

TheSolarEdgepowerharvestingsolutionisdesignedtomaximizethepoweroutputfromanytypeof

solarPhotovoltaic(PV)installationwhilereducingtheaveragecostperwatt.Thefollowingsections

describeeachofthesystem’scomponents.



Figure 1: The SolarEdge power harvesting system components

Power Optimiser

ThepoweroptimisersareDC-DCconvertersconnectedtoPVmodulesinordertomaximizepower

harvestingbyperformingindependentMaximumPowerPointTracking(MPPT)atthemodulelevel.

Thepoweroptimisersregulatethestringvoltageataconstantlevel,regardlessofstringlengthand

environmentalconditions.

Thepoweroptimisersincludeasafetyvoltagefunctionthatautomaticallyreducestheoutputofeach

poweroptimiserto1Vdcinthefollowingcases:

lDuringfaultconditions

lThepoweroptimisersaredisconnectedfromtheinverter

lTheinverterON/OFFswitchisturnedOFF

lThesafetyswitchontheConnectionUnitisturnedOFF

lTheinverterACbreakeristurnedOFF

lTheRapidShutdown(PVRSS)isinitiatedbyoneofthefollowingmethods:

oInverterACbreakeristurnedOFF,orACtotheinverterisdisconnectedbyanothermethod

(intentionallyorasresultofafault)

oInverterON/OFFswitchisturnedOFF

oTheConnectionUnitisturnedOFF

EachpoweroptimiseralsotransmitsmoduleperformancedataovertheDCpowerlinetotheinverter.

Twotypesofpoweroptimisersareavailable:

lModuleAdd-onpoweroptimiser–connectedtooneormoremodules

lSmartmodules-thepoweroptimiserisembeddedintoamodule

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

10

Chapter 1: Introducing the SolarEdge Power Harvesting System

Three Phase Inverter with Synergy Technology

TheThreePhaseInverterwithsynergytechnologyinverter(referredtoas'inverter'inthismanual)

efficientlyconvertsDCpowerfromthemodulesintoACpowerthatcanbefedintothemainACservice

ofthesiteandfromtheretothegrid.Theinverteralsoreceivesthemonitoringdatafromeachpower

optimiserandtransmitsittotheSolarEdgemonitoringplatform(requiresInternetorCellular

connection).

TheinverteriscomprisedofonePrimaryUnitwithanintegratedConnectionUnitwithaDCSafety

Switch(referredtoas'ConnectionUnit'inthismanual)fordisconnectingtheDCpowerofaSolarEdge

system,andofoneortwoSecondaryUnits,dependingontheinverter'scapacity.TheSecondaryUnit(s)

areconnectedtotheprimaryunitwithAC,DCandcommunicationcables.

Eachunitoperatesindependentlyandcontinuestoworkincasetheothersarenotoperating.

Youcansetupamaster-slaveconfiguration,connectingupto31additionalinverterstoonemaster

inverter.

Figure 2: Primary Unit with two Secondary Units



Chapter 1: Introducing the SolarEdge Power Harvesting System

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

11

Monitoring Platform

Themonitoringplatformenablesmonitoringthetechnicalandfinancialperformanceofoneormore

SolarEdgesites.Itprovidespastandpresentinformationonthesystemperformancebothatthesystem

andmodulelevels.

Supported ACGrids

ThefollowingsectionshowstheACgridssupportedbytheinverters(modeldependent).

Groundconnectionisrequiredforallgrids,asdescribedinConnectingtheACGridandGroundingtothe

ConnectionUnitonpage37.

Figure 3: AC grids supported by SolarEdge three-phase inverters

NOTE

Somethreephaseinverterssupportthe208VDeltagrid.RefertoSettingtheInverterto

Support208V3-wireGridonpage41.

Installation Procedure

ThefollowingistheprocedureforinstallingandsettingupanewSolarEdgesite.Manyofthesealsoapply

tomodificationofanexistingsite.

1. InstallingthePoweroptimisers,page14

2. MountingandConnectingthePrimaryandSecondaryUnit(s),page29

NOTE

It is recommended to connect communication connections (step 6 of this installation) before

connecting the AC, for easier access to the communication board.

3. ConnectingtheACandtheStringstotheConnectionUnit,37

4. ActivatingandCommissioningtheSystemUsingSetApp,page42

5. ConfiguringtheSystemUsingSetApp,page44

6. SettingUpCommunicationpage57



-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

12

Monitoring Platform

Installation Equipment List

StandardtoolscanbeusedduringtheinstallationoftheSolarEdgesystem.Thefollowingisa

recommendationoftheequipmentneededforinstallation:

lAllenscrewdriverfor5mmscrewtypefortheinvertercover,ConnectionUnitcover,andinverterside

screws

l17/32HEXAllenscrewdriverforACstudconnector

lSolarEdgesuppliedlevel

lSolarEdgesuppliedDC/interlockconduit(s)

lStandardflat-headscrewdriversset

lNon-contactvoltagedetector

lCordlessdrill(withatorqueclutch)orscrewdriverandbitssuitableforthesurfaceonwhichthe

inverterandoptimiserswillbeinstalledandforopeningtheConnectionUnitdrillguides.Useofan

impactdriverisnotallowed.

lAppropriatemountinghardware(forexample:stainlessbolts,nuts,andwashers)forattaching:

othePrimaryandSecondaryUnit(s)mountingbracketstothemountingsurface

othepoweroptimiserstotheracking(notrequiredforsmartmodules)

l4xM8ringterminalsandsuitablecrimper

lWirecutters

lWirestrippers

lVoltmeter

Forinstallingthecommunicationoptions,youmayalsoneedthefollowing:

lForEthernet:

oCAT5/6twistedpairEthernetcablewithRJ45connector

oIfusingaCAT5/6cablespool:RJ45plugandRJ45crimper

lForRS485:

oFour-orsix-wireshieldedtwistedpaircable.

oWatchmakerprecisionscrewdriverset

Chapter 1: Introducing the SolarEdge Power Harvesting System

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

13

Chapter 2: Installing the Power Optimisers

Safety

ThefollowingnotesandwarningsapplywheninstallingtheSolarEdgepoweroptimisers.Someofthe

followingmaynotbeapplicabletosmartmodules:

WARNING!

The metallic enclosure of the power optimiser must be grounded in accordance with the product's listing

and local and national codes.

L'enceinte métallique de l’optimiseur de puissance doit être mise à la terre en accord avec les

régulations locales et nationales.

WARNING!

When modifying an existing installation, turn OFF the inverter ON/OFF switch, the Connection Unit and

the AC circuit breaker on the main AC distribution panel.

Avant de faire ces étapes, éteignez l'onduleur monophasé en mettant sur OFF l'interrupteur ON/OFF

situé au bas de l'onduleur.

CAUTION!

Power optimisers are IP68/NEMA6P rated. Choose a mounting location where optimisers will not be

submerged in water.

Les optimiseurs de puissances sont compatibles à la norme IP68/NEMA6P. Choisissez le lieu de

montage tel que l’optimiseur ne puisse pas être submergé par l’eau.

CAUTION!

This unit must be operated according to the operating specifications provided with the unit.

Cette unité doit être opérée suivant les instructions trouvées dans le manuel fourni avec le produit.

CAUTION!

Cutting the power optimiser input or output cable connector is prohibited and will void the warranty.

Sectionner les cables d’entrées ou de sortie de l’optimiseur est interdit et annule sa garantie.

CAUTION!

All PV modules must be connected to a power optimiser.

Tous les modules doivent être connectés à un optimiseur de puissance.

CAUTION!

If you intend to mount the optimisers directly to the module or module frame, first consult the module

manufacturer for guidance regarding the mounting location and the impact, if any, on module warranty.

Drilling holes in the module frame should be done according to the module manufacturer instructions.

Pour installation à même le module ou la monture du module, consultez d'abord le fabricant du module

sur la position et son impact sur la garantie du module. Le perçage de trous dans le cadre du module

devra se faire suivant les instructions du fabricant.

IMPORTANT SAFETY FEATURE

Modules with SolarEdge power optimisers are safe. They carry only a low safety voltage before the

inverter is turned ON. As long as the power optimisers are not connected to the inverter or the inverter is

turned OFF, each power optimiser will output a safe voltage of 1V.

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

14

Chapter 2: Installing the Power Optimisers

CAUTION!

Installing a SolarEdge system without ensuring compatibility of the module connectors with the

optimiser connectors may be unsafe and could cause functionality problems such as ground faults,

resulting in inverter shut down. To ensure mechanical compatibility of the SolarEdge optimisers’

connectors with the PV modules’ connectors to which they are connected:

lUse identical connectors from the same manufacturer and of the same type on both the power

optimisers and on the modules; or

lVerify that the connectors are compatible in the following way:

oThe module connector manufacturer should explicitly verify compatibility with the SolarEdge

optimiser connector; and

oA third-party test report by one of the listed external labs (TUV, VDE, Bureau Veritas UL, CSA,

InterTek) should be obtained, verifying the compatibility of the connectors.

ATTENTION!

Les connecteurs du module doivent être mécaniquement compatibles avec les optimiseurs de

puissance. Sinon, le système SolarEdge installé peut être dangereux ou causer des problèmes

fonctionnels, tels que les défauts de terre, qui peuvent provoquer un arrêt de l’onduleur. Afin d'assurer la

compatibilité mécanique entre les optimiseurs de puissance SolarEdge et les modules auxquels ils sont

connectés:.

lUtiliser des connecteurs identiques du même fabricant et du même type aussi bien pour les

optimiseurs de puissance que pour les modules.

lVérifiez que les connecteurs sont compatibles de la manière suivante:

oLe fabricant du connecteur doit explicitement vérifier la compatibilité avec le connecteur

SolarEdge.

oUn rapport de test de tierce partie doit être effectué par l’un des laboratoires externes indiqués ci-

dessous:(TUV, VDE, Bureau Veritas UL, CSA,Intertek), qui vérifiera la compatibilité des

connecteurs.

Package Contents

lPoweroptimisers

lStainlesssteelgroundinglockwashers

Installation Guidelines

lFrame-mountedpoweroptimisersaremounteddirectlyonthemoduleframe,

regardlessofrackingsystem(rail-lessorwithrails).Forinstallationofframe-mounted

poweroptimisers,refertohttp://www.solaredge.com/sites/default/files/installing_

frame_mounted_power_optimizers.pdf.

lThestepsinthischapterrefertomoduleadd-onpoweroptimisers.Forsmart

modules,startfromStep3:ConnectingPowerOptimisersinStringsonpage19.Also

refertothedocumentationsuppliedwiththesmartmodules.

lThepoweroptimisercanbeplacedinanyorientation.

lIfconnectingmoremodulesthanoptimiserinputsinparallel,useabranchcable.Somecommercial

poweroptimisermodelshaveadualinput.

lPositionthepoweroptimisercloseenoughtoitsmodulesothattheircablescanbeconnected.

lMakesuretousepoweroptimisersthathavetherequiredoutputconductorlength:

Chapter 2: Installing the Power Optimisers

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

15

oDonotuseextensioncablesbetweenamoduleandapoweroptimiser,betweentwomodules

connectedtothesameoptimiser,orbetweentwooptimisersotherthaninthecasesspecified

below.

oYoucanuseextensioncablesbetweenpoweroptimisersonlyfromrowtorow,aroundobstacles

withinarow,andfromtheendofthestringtotheinverter,aslongasthemaximumdistanceis

notexceeded.

lTheminimumandmaximumstringlengthguidelinesarestatedinthepoweroptimiserdatasheets.

RefertotheDesignerforstringlengthverification.TheDesignerisavailableontheSolarEdgewebsite

athttps://www.solaredge.com/us/products/installer-tools/designer#/.

lCompletelyshadedmodulesmaycausetheirpoweroptimiserstotemporarilyshutdown.Thiswill

notaffecttheperformanceoftheotherpoweroptimisersinthestring,aslongastheminimum

numberofunshadedpoweroptimisersconnectedinastringofmodulesismet.Ifundertypical

conditionsfewerthantheminimumoptimisersareconnectedtounshadedmodules,addmore

optimiserstothestring.

lEquipmentgroundingtighteningtorques:4-6AWG:45lb-in,8AWG:40lb-in,10-14AWG:35lb-in.

lToallowforheatdissipation,maintaina2.5cm/1"clearancedistancebetweenthepoweroptimiser

andothersurfaces,onallsidesexceptthemountingbracketside.

Figure 4: Power optimiser clearance

lWheninstallingmodulesinaconfinedspace,forexample,ifinstallingBuilding-integratedphotovoltaic

(BIPV)modules,ventilationmeasuresmaybeneededtoensurethepoweroptimisersarenotbe

exposedtotemperaturesoutsidetheirspecifications.

NOTE

The images contained herein are for illustrative purposes only and may vary depending on product

models.

Step 1: Mounting and Grounding the Power

Optimizers

Foreachofthepoweroptimisers1:

1Not applicable to smart modules.

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

16

Step 1: Mounting and Grounding the Power Optimizers

1. Determinethepoweroptimisermountinglocationandusethepoweroptimiser

mountingbracketstoattachthepoweroptimisertothesupportstructure(See

Figure5).Itisrecommendedtomountthepoweroptimiserinalocationprotected

fromdirectsunlight.Forframe-mountedpoweroptimisersfollowtheinstructions

suppliedwiththeoptimisers,orreferto

https://www.solaredge.com/sites/default/files/installing_frame_mounted_power_

optimizers.pdf.

2. Ifrequired,markthemountingholelocationsanddrillthehole.

CAUTION!

Drilling vibrations may damage the power optimiser and will void the warranty. Use a torque wrench

or an electric drill with adjustable clutch that meets the mounting torque requirements. Do not use

impact drivers for mounting the power optimiser.

Do not drill through the power optimiser or through the mounting holes.

ATTENTION!

Les vibrations résultant du perçage peuvent endommager l’optimiseur de puissance et annulera la

garantie. Utilisez une clé dynamométrique ou une perceuse électrique avec embrayage adaptable

compatible avec les moments indiqués. Ne pas utiliser des tournevis à percussion pour fixer

l’optimiseur. Ne pas percer à travers l’optimiseur de puissance ou ses trous de fixation.

3. AttacheachpoweroptimisertotherackusingM6(1/4'')stainlesssteelbolts,nutsandwashersor

otherappropriatemountinghardware.Applytorqueof9-10N*m/6.5-7lb*ft.

For3NAseriespoweroptimizes,SolarEdgerecommendsmountingthepoweroptimiseronarailwith

thesmoothsidefacingout,sothatthepoweroptimiserbodywillpreventitsrotation.

4. Usethefollowingmethods1togroundthepoweroptimizer:

WARNING!

The metallic enclosure of the power optimiser must be grounded in accordance with the

requirements of the local and national codes.

AVERTISSEMENT!

L'enceinte métallique de l’optimiseur de puissance doit être mise à la terre en accord avec les

régulations locales et nationales.



lFor mounting on a grounded metal rail:Usetheprovided5/16''stainlesssteelgroundingstar

washerbetweentherailingandtheflatsideofthemountingbracket.Thegroundingwasher

shouldbreakthroughtheanodizecoatingoftherailingtoensurelowresistiveconnection.Apply

torqueof9.5N*m/7lb*ft.SeeFigure5.

1These methods have been evaluated by a nationally recognized testing laboratory as part of the optimiser evaluation.

The SolarEdge-supplied grounding lug kit has been evaluated only for use with SolarEdge power optimizers. It is not

intended or listed to be used as a general purpose grounding lug with other electrical equipment.

Chapter 2: Installing the Power Optimisers

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

17

Figure 5: Power optimiser installation and grounding using a star washer

lFor mounting on rails with sliding nut fasteners:Ifthestarwashercannotbeused,usethe

SolarEdgegroundingplate(purchasedseparately)betweentherailingandtheflatsideofthe

mountingbracket.Usemountingspecifichardwareasneeded.Applytorqueof9.5N*m/7lb*ft.

SeeFigure6

Figure 6: Power optimiser installation and grounding using a grounding plate

lFor mounting on un-grounded structures(suchasawoodenstructure):Ifthestarwasheror

theplatecannotbeused,usetheSolarEdgegroundinglug(purchasedseparately)withan

equipment-groundingconductoraccordingtothesuppliedinstructions.Thegroundingterminal

acceptsawiresizeof6-14AWG,andmustbesizedforequipmentgroundingperNEC250.122

requirements.Tightenthescrewsconnectingthepoweroptimisertotheframeandthe

groundingterminalscrew.Applytorqueof9.5N*m/7lb*ft.SeeFigure7

Figure 7: Power optimiser grounding terminal

5. Verifythateachpoweroptimiserissecurelyattachedtothemodulesupportstructure.

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

18

Step 1: Mounting and Grounding the Power Optimizers

6. Recordpoweroptimiserserialnumbersandlocations,asdescribedinReportingandMonitoring

InstallationDataonpage54.

Step 2: Connecting a PV Module to a Power

Optimiser

NOTE

Images are for illustration purposes only. Refer to the label on the product to identify the plus and

minus input and output connectors.

Foreachofthepoweroptimisers:

lConnectthePlus(+)outputconnectorofthemoduletothePlus(+)inputconnectorofthepower

optimiser.

lConnecttheMinus(-)outputconnectorofthemoduletotheMinus(-)inputconnectorofthe

poweroptimiser.

Figure 8: Power optimiser connectors

Step 3: Connecting Power Optimisers in Strings

Youcanconstructparallelstringsofunequallength,thatis,thenumberofpoweroptimisersineach

stringdoesnothavetobethesame.Theminimumandmaximumstringlengthsarespecifiedinthe

powerdatasheets.RefertotheSolarEdgeSiteDesignerforstringlengthverification.

NOTE

lUse at least 11 AWG/ 4 mm² DC cables.

lThe total conductor length of the string (excluding power optimisers’ conductors; including home

runs and necessary extensions between optimisers) should not exceed:

IMPORTANT SAFETY FEATURE

lFor a compliant PV Rapid Shutdown (PVRSS) installation, use no more than 30 optimisers per

string.

lEnabling PVRSS from the inverter menu is only required if the installed optimisers were

manufactured before 2015, otherwise it is enabled by default.

NOTE

The DC bus of each unit is separate and not shared for all units. Therefore in addition to following the

inverter design rules, each unit should follow the unit design rules as detailed in the Technical

Specifications.

Chapter 2: Installing the Power Optimisers

-Three Phase Inverter with Synergy Technology Installation MAN-01-00402-1.4

19

Page is loading ...

SolarEdge SE100KUS Installation guide

This manual is also suitable for

SolarEdge SE100KUS Installation guide

Related papers

Other documents