Read this manual carefully
before using the product!
Translated from the original
34-FHBTN
FEEDER
WITH ROOF & COVERED TOMBSTONE RAILINGS
TABLE OF CONTENTS
Introduction 3
Product information 3
Entended Use 3
Technical data 3
Safety information 4
Safety Information when using the product 4
Incase of emergencies 4
Personal Protection 5
safety measures Before operating 5
Transport and Storing 5
Warning Decals 6
Feeding horses in the eld 7
Maintenance and service 7
Recycling 7
Selecting feeders for animals 8
34-FHBTN information 9
Parts included 34-FHBTN 10
Assembly instruction 11
Assembly - Base 12
Assembly - corner post and tube arches for the roof 13
Assembly - Stabilizers 14
Assembly - roof protection 15
Roof Assembly 16
Metal sheet Belt assembly 17
Gate Assembly 18
Deviation request form 19
EC-Declaration of conformity, original 20
Table of contents→
INTRODUCTION
Thank you for choosing a product from Kellfri AB. By following the general safety information
and the instruction manual and by using common sense, you will have a great and safety use
of your Kellfri product for many years. Kellfri designs and delivers eective, aordable ma-
chinery and components for forest, agriculture, construction and gardening in Sweden, other
Nordic countries and Europe.
PRODUCT INFORMATION
• Feeder with tombstone railings for horses with covered tombstone railings
• Adjustable roof height
• 3 base supports provide good stability
• Bale rell opening, 181 cm
This feeder with 12 openings is designed and adapted for horses.
To prevent horses from injuring themselves on the roof edges, these have been equipped with
a protection arch made from tubular pipes. The tombstone railings are covered and the gaps
are adapted to minimise the risk of horses becoming stuck. From the ground to the bottom of
the tombstone railing is 65 cm and 132 cm to the top of the tombstone railing. The CC dimen-
sion between tombstone railings is 59 cm. The feeder can be replenished easily by opening
any of the four gates, which open out to the side, the opening width is 181 cm and large bales/
round bales t in the feeder.
The height of the roof is adjustable by 30 cm for maximum protection against precipitation
and for adjustment to suit the size of the horses. Three base supports ensure that the feeder is
stable and does not sink into the ground in wet conditions.
ENTENDED USE
Kellfri’s feeders are only intended to use for feeding animals, can use for feeding horses, Sui-
table for round and square hay bale. Pls. follow your country’s Agricultural rules and Animal
Welfare Act.
Dierent animals/ individuals have dierent capabilities, behavior and temperament. It
is important to choose the suitable feeder for the type of animal/cattle/horses. When
suspected that the individuals can get injured in combination of feeder and animals
(adult/ young animals), measures shall be taken before any feeder is placed to mini-
mized the risk for injuries.
PLEASE NOTE that any risk of injury is greater to smaller bread and or foal/calf/ young
animals because the feeders measurements are adapted for adult animals.
TECHNICAL DATA 34FHBTN
More Information 2 000 mm
Tombstone railing 43 mm ø
Feed openings 12
Total width 2,000 mm
Total length 2,000 mm
Weight 403 kg
←Table of contents
INCASE OF EMERGENCIES
In case of an emergency please dial 112.
Keep cell phone or emergency phone available specially when working alone. First aid kit and
re extinguishers must be kept easily accessible during all work, maintenance and service.
SAFETY INFORMATION
Before using the product, please read the safety information and instruction manual and un-
derstand its contents for your own and others’ safety. Always keep the safety information and
instruction manual easily accessible to the user of the product. Remember that it may be good
for your own and others’ safety to read the safety information every now and then. If the in-
structions manual is damaged or otherwise unusable, please contact your retailer and order
a new one
The general safety instruction is also available from Kellfri’s website: www.kellfri.com
Do not work with the product if you are feeling sick, tired or in inuence of alcohol. Nor if you
are under the inuence of strong medications or drugs, suering from strong depression or
severe mental illness. Always follow the general trac rules and regulations during relocation
of the feeder and the rules of the Animal Welfare Act.
Kellfri disclaim any responsibility for self-made modications, changes or alterations.
Kellfri AB disclaims responsibility for the animals and their behavior.
SAFETY INFORMATION WHEN USING THE PRODUCT
• Always make sure that suitable feeder is use for the type of animal to ensure function
and safety of the animals.
• Always follow the rules in the animal welfare act.
• There is often a lot of pressure around the feeder when feeding combined adult animals
/foal /calf. There is always an increased risk for young animals (foal/calf ) to get injured.
• Always check that the feeder is not damage before use.
• Supervision of the animals is required at least onces a day during feeding.
• Avoid having too few feeder to the number of animals
• Ensure that the feeder never stand empty. When feeding horses, horses should always
have unlimited access to hay.
• When the feeder is not in use, store it a safe place where no animals resides.
• Danger zone is 5 meter. Nobody except for the operator is allowed in the vicinity of the
feeder during relocation.
• During transport, always follow the general trac rules and regulations.
• Nobody under any circumstances are allowed to stay underneath the feeder when it is
up-lifted
• The feeder shall be placed on a level ground, not sunk into the ground or covered with
snow during winter. The surface aroun the feeder shall always keep clean to guarantee
the the the safety of the animals and stability of the feeder.
Warning!
The product must not in any circumstances be modified without permission from the
manufacturer. Unauthorized modification of the machine and/or accessories can cause
fatal injuries or death to operator or others.
Table of contents→
PERSONAL PROTECTION
Always wear suitable clothing and footwear. Wear protective gloves, hearing protection, eye
protection and protection mask should be use when necessary.
SAFETY MEASURES BEFORE OPERATING
Read the safety information and instruction manual carefully. Be sure you understand the safe-
ty measures, instruction manual and warning labels. Use common sense when operating the
machine and use appropriate personal protective equipment. Do visual inspection of equip-
ment or product before use. Fix or replace damaged or worn parts immediately to reduce the
risk of injury. Check that all screw-nuts and bolts are tightened.
The product should not be taken into use unless it can be done in a safe way for the user.
• Always check the product before it’s placed in place.
• Damage or cracked feeders should NEVER be use. Risk to severe injuries for the animals
• Check all part of the feeder is intact/ no damage before assembly. Assemble the feeder
using pins and bolts.
Never use a equipment or product with defect safety equipment.
Warning!
TRANSPORT AND STORING
Make sure there are no people, children and foreign objects around the area before transport-
ing the machine. Always take an extra caution during the transport. Ensure that the product
is well secured and that transport brackets are mounted. Always place the load as low as pos-
sible. Respect the danger zone even during transport. When lifting the equipment, never go
underneath suspended loads. Trailer used for transport should have working brakes.
Always store the product in a dry place preferably underneath a cover when not in use. Ensure
that the product is stable and not likely to tip over. Never let children play where the machine
is being stored. Always keep in mind the risk of tipping!
For safety, this product should only be used in the manner described in this manual.
The user is responsible for the instruction to be read through and followed.
Warning!
←Table of contents
SYMBOL EXPLANATION
Read the manual before using the product
Danger zone 5 m around the feeder during transport
Accident risk! Keep children in the area supervised
Warning! Risk of crushing!
No one is allowed to stand underneath suspended load.
Warning! No one is allowed to be in the vicinity of the product
Important! Keep the product under a roof or cover it when not in
use. This extends the life of your product.
Moving from one place to another
• Check that the feeder is undamaged before moving it. This should only be done when
the feeder is empty.
• Make sure that the pallet fork bracket is not damage
• Lift only on designated points
• Drive carefully and check the movements of the feeder.
• The feeder should be moved with caution! Maximum speed during transport is 5 km / h.
• Place the feeder low during all transport.
Warning!
Children in the area should be supervised.
WARNING DECALS
Make sure warning decals are always visible and clean them when necessary. Do not use a
high-pressure washer directly on the warning label. If a decal becomes worn or in any other
way unusable, order a new set of decals.
Table of contents→
MAINTENANCE AND SERVICE
Ensure that the unit is stable and cannot tip over during maintenance and service. Replace
damaged or worn parts immediately to reduce the risk of abrasion. Always perform mainte-
nance, service and inspection, as recommended. Use only original replacement parts or spare
parts with equivalent performance to reduce the risk of damage.
• Regularly check the condition of the product. If cracks, bends are detected, don’t use the
product, rectify the damage or replace the feeder.
• Worn parts should be replaced. Check that all locking pins are correctly mounted. Flush
the feeder with water if necessary.
RECYCLING
Disposal of the product, disassemble and transport to the municipality’s
recycling station. Contact your local authority for further information.
Kellfri AB is working continuously to develop their products and therefore reserves the right
to modify, among other things, the design and appearance without any further notice.
Discarded feeder should be diposed on your local recycling station.
Important !
FEEDING HORSES IN THE FIELD
• If you have more than one horse in the eld and they are fed with roughage, it is impor-
tant to have a fair distance between the pile of hay or feeders. Put out more piles of hay or
feeders than horse running in the yard, it is safer that way. The feeding site should always
be clean and dry. Avoid having too few feeder for the number of animals.
• The feeder should not stand empty! Kellfri feeders are intended for feeding animals do
not use it for other purposes, or ll it with other materials.
• When the feeder is not in used, do not leave it in the eld.
• Keep in mind that you are responsible for your animals! Ensure that the animals cannot
get injured when using the feeder. If there is any suspicion that the animals may get in-
jured, the feeder should not be used. Kellfri AB disclaims responsibility for the animals be-
havior. With horses behavior, it might be that they want to “play” with an empty feeder for
which it is not intended. Therefore is it important that you keep your animal supervised!
Risk of serious injuries!
• Feeding time often results pressure on animals, combination adult animals with young
animals, always caused an increased risk for injuries for young animals.
• Always check that the feeder is undamaged before using them.
• IMPORTANT! Supervision shall be carried out at least once a day during use. There is a risk
that animals get stuck in the feeder.
• The feeder should be place on a level surface and not soaked in the ground or in food and
snow. In order to guarantee the safety of the animal and the feeders stability, the surface
around the feeder should be kept clean.
• Always make sure there is food in the feeder. When the feeder is used for horses, they
must have free access to roughage.
←Table of contents
IMPORTANT TO KEEP IN MIND WHEN SELECTING FEEDERS FOR ANIMALS
Whether you have horse, cattle or sheep, there are dierent types of races, ages, individuals
and hence dierent behaviors. You know your animals best and their behavior and we ask
you to think about how the animals react in dierent situations where a feeder is involved
so no injuries occurs. If there are too many animals around the same feeder, competition
increases and thus the pressure on the feeder increases and the risk of injury increases.
You are responsible for the choice of feeder model as you know your animals best - How
many animals should be around a feeder, how the ranking is in the ock is crucial for the size
of the feeder and how many feeders are appropriate. In the case the feeder is going to be for
of animals with horns, one must take this into account the choice of feeder.
When using metal feeder, there may be sharp edges. It is required for you to check that the
product cannot cause any harm to the animals. Take the habit of checking the feeder periodi-
cally and prior to use. Make sure there are no sharp edges and corners.
You as the owner of the animal is responsible for the equipment used for your animal.
Ensure that the ground area and around the feeder is well drained, dry and clean.
Keep up to date about rules and regulations through your local Agricultural Agency’s concern-
ing feeding of animals in the eld.
Good to know
When the temperature drops iron and steel are aected by low temperatures in such a way
that the material becomes brittle. When the temperature drops the impact strength of the
metal decreases in a certain temperature range, the so-called transition zone. At temperatures
below this zone, the material becomes easier for brittle fractures.
MPORTANT! When the tempera-
ture drops below -25 degrees, it is
important to remember that steel
strength deteriorates. Then it is
extra important to check that the
feeder has no cracks.
Table of contents→
Covered tombstone railings.
The feeder has pallet fork insertion points so that
you can easily lift and move it.
Feed can be replenished easily by opening any
of the four gates, which open out to the side,
the opening width is cm and large bales/
round bales t in the feeder.
The height of the roof is adjustable by cm for
maximum protection against precipitation and
for adjustment to suit the size of the horses.
Three base supports ensure that the feeder is
stable and does not sink into the ground in wet
conditions.
34FHBTN INFORMATION
←Table of contents
Abase 1st F2 foot rack middle 1st
Bcorner posts (B1-left,B2 right) 4st Gtube arch - roof 2st
Cmetal sheet belts 2st Hprotection arch -front 2st
Dtube for the protection arch 2st Iroong panel - 2,3m 3st
Estabilizers 2st Jfeeder gate 4st
F1 foot rack 2st Kmounting kit 1set
M10x25 - 14pcs
M10x55 - 4pcs
M12x25 - 4pcs
M12x50 - 8pcs
M10 - 18pcs
M12 - 12pcs
M12 Lock nut - 8pcs
M8 - 4pcs
Washer Ø8 - 4pcs
M8x60 - 4pcs
Pin with chain: Ø12x 60mm - 8pcs
A
DH
C
E
G
K
F1 F2
PARTS INCLUDED 34FHBTN
I
J
B1
B2
Table of contents→
8 pcs - Pin with chain
4 pcs - M8x60
8 pcs - M12x50
14 pcs - M10x25
4 pcs - M10x55
4 pcs - M12x25
ASSEMBLY INSTRUCTION
• It is recommended that the assembly is carried out by at least 2 persons.
• Check that all parts are intact and nothing is missing.
• Assemble according to assembly instructions. Take the help of a good friend if needed.
Table of contents→
Step 6
Step 5
Mount the arch tube (H) 2 pcs, on each side
Mount the side tubes 2pcs (D) on
each side of the tube arche, use the
bolts M8x60 to secure them 4 pcs.
- remove the bolt
- Install side tubes
- remount the bolt and
turn the nut a few turns
(do not tighten yet)
- repeat the procedure
in each corner
H
ASSEMBLY ROOF PROTECTION
D
Table of contents→
METAL SHEET BELT ASSEMBLY
Step 8
Mount one end of the belt with M8x60, throw the belt over the roof to the other side.
Do same procedure for the other metal sheet belt.
Mount the strap in each corner (1) (see pictures below), tighten the strap (2) so that side tubes
pulls up closer to the roof. This step facilitates the mounting of the metal sheet belt (3) on
the other side. The straps also work as a safety precaution so that the side tubes does not fall
during assembly. Tighten all bolts (4) so that the roong belts are securely attached.
In this step we used straps to pull up the side tubes, making it easier to thighten the the
metal sheet belts and secure them in place.
12
3 4
Table of contents→
We are grateful for your help pointing out any inaccuracies in the Kellfri product delivered to you. Before making a complaint
please read Kellfri’s Purchasing terms in our catalog or Kellfri’s website at www.kellfri.co.uk as well as enclosed User’s manual
that comes with the machine.
Please fill in the details below and attach photo or other information in order to process your request. To get the best information
regarding the possible errors in the machine / product we would like to ask you to take 4 pictures on the machine / product - 2
on the entire machine from 2 dierent angles and 2 close-ups on the error itself from 2 dierent angles.
We sell our products through selected retailers. Please contact your retailer for the applicable purchase and delivery terms.
REASON YES
(11) Shipping damage*
(09) Product reclamation*
(04) Wrong delivery of product
(03) Wrong quantity
Buyer: Customer no:
Address: Invoice no:
E-mail: Phone no:
Buyer’s signature: Date:
Signiture: Date:
Dealer information: Invoice no.:
When was the product delivered?
When was the product taken into operation? Did the product function as it should upon
delivery?
Product name or No:
Serial no.:
DEVIATION REQUEST FORM
KELLFRI AB
Munkatorpsgatan 6
SE-532 37 SKARA
Phone +46 (0)511-242 50
Fax +46 (0)511-168 33
Web: www.kellfri.se
E-mail: [email protected]
Send the form and photos to:
Kellfri AB
Service department
Munkatorpsgatan 6
532 37 Skara
Or e-mail Service
Please provide a description of the defected product/part or what the error is :
Describe event progress:
Other information:
Updated: 20181128
Yes No
REASON YES
(05) Wrong price
(02) Wrong order /Charge-back
(99) Other reason *
* Please ll the form below as detailed as possible
To be completed by the dealer
Case No.:
WARRANTY TERMS AND CONDITIONS
Validity of the warranty - Kelifri’s Warranty is valid 12 months from the date of purchase.
This warranty replaces - Compensation for spare parts after acknowledgment that the
fault lies on the material or manufacturing defects.
This guarantee do not
cover
• Labour costs
• Travel expenses
• Any modification that the buyer himself has/had made.
• Any consequential damages that occurred due to damage to the machine.
• Damage due to normal deterioration of the machine, inadequate: service,
user inexperience or use of spare parts which are not original.
• Wear parts such as hoses, seals, oils, and mechanical belts
CUSTOMER SERVICE
You are always welcome to give your feedbacks, reviews or ask us about our equipment and products.
Kellfri AB is constantly working on further developing their products and therefore reserves the right to
modify, among other things the design and appearance without further notice.
KELLFRI AB
Phone no: +46 (0)511 - 242 50
Fax: +46 (0)511 - 168 33
E-post: [email protected]
Kjell Johansson
Product Development Manager
According to 2006/42/EC, Annex 2A
Kellfri AB
Munkatorpsgatan 6
532 37 Skara, Sweden
Declares that the machine
Name: 34-FHBTN
Type: Feeder with roof and covered tombstone railings
Complies with all applicable provisions of the Directive 2001/95/EG, General Product Safety
EC-DECLARATION OF CONFORMITY, ORIGINAL
Latest change 07/10/2021
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kellfri 28-CVB Owner's manual
-
Kellfri 16-PGF2000 Owner's manual
-
Kellfri 34-FHH8 Owner's manual
-
Kellfri 25-T300K Owner's manual
-
Kellfri 28-V+ Owner's manual
-
Kellfri 27-V18ATV Owner's manual
-
Kellfri 28-VBS+ Owner's manual
-
Kellfri 25-T6003 Owner's manual
-
Kellfri 21-KGS70 Owner's manual
-
Kellfri 23-VV800 Owner's manual
Other documents
-
FOERSTER TECHNIK Automatic Calf Feeder User guide
-
FORSTER TECHNIK CalfRail User guide
-
FOERSTER TECHNIK FOERSTER-TECHNIK Combi Automatic Calf Feeder User guide
-
Chore-Time MA854H Drop Feeding Installation and Operators Instruction Manual
-
Chore-Time MA854F Drop Feeding Installation and Operators Instruction Manual
-
Rankam HU2327701-GW Owner's manual
-
Rankam HU2327901-GW Owner's manual
-
Grizzly G4179 Owner's manual
-
HUSTLER Unrolla TX205 | TE205 Owner's manual
-
Powermatic PF-31 Feeder, 1HP 1PH 115V, 4 Speed User manual
