© 2021
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View 10’
10’
VK-1100 - 10’ x 10’ Hybrid Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2021
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2021
Crate 1 of 1
Order #XXXXX Crate Packing
© 2021
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
1/1A
2/2A
3/3A
4/4A
5
Qty.
1/1
1/1
1/1
1/1
1
Description
Base Plate
80”h Vertical Extrusion
86”w Horizontal Extrusion w/ Velcro
86”w Horizontal Extrusion
86”w Horizontal Mounting Plate
Steps:
1) Connect base plate [1] to the base of vertical [2];
connect base plate [1A] to the base of vertical [2A].
2) Attach horizontals [3], [3A], [4], [4A] & [5] between verticals.
1A
13
4
4A
5
3A
2
2A
Velcro: Top
Edge
Velcro: Bottom
Edge
Velcro: Inside
Edge
Velcro: Inside
Edge
FRONT VIEW
Backwall Assembly
© 2021
Step 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Item
6
7
8
9
- -
Qty.
1
1
1
1
1
Description
89.965”w Horizontal Extrusion
14”h Vertical Extrusion
8.738”h Vertical Extrusion
92.9223”w Curved Horizontal Extrusion
Ceiling w/ Lighting
Steps:
1) Attach verticals [7] & [8] to the ends of horizontal [6].
2) Connect curved horizontal [9] to the tops of verticals [7] & [8].
3) Attach Ceiling to the tops of verticals [2] & [2A]; use bolts provided.
4) Connect assembled header frame to the top of ceiling; use bolts provided.
FRONT VIEW
6
9
7
8
Ceiling w/ Lighting
Velcro: Middle
Velcro: Middle
Velcro:
Middle
Velcro:
Middle
When assembled
Header & Ceiling Assembly
© 2021
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
2
Steps:
1) Affix fabric Header Graphic to header frame, using Velcro.
2) Affix fabric Backwall Graphic to Velcro on backwall frame, as shown.
3) Attach Wings to vertical [2]. See Wing Attachment detail.
When assembled
1) Slide A10 connector
into groove of extrusion.
2) Tighten set screw to
secure A10 to extrusion.
3) Insert Wing into Clamp.
4) Tighten knob to secure
wing in place.
Wing Attachment
*
Wing
1
2
3
4
W
i
ng
*
*
*
*
He
a
der Gra
p
h
i
c
Bac
k
wall
G
ra
p
hi
c
Graphics & Wing Attachment
© 2021
Step 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Cabinet
Backwall
Threaded
Hole
Insert screw cap through hole of cabinet backwall
into threaded hole of horizontal extrusion [4].
Twist and tighten screw cap to secure in place.
Cabinet to Horizontal Attachment
Screw Cap
Extrusion 4
*
Cam Lock w/ Pill Slot Attachment
*
Tighten screw to clamp cam lock
into groove of vertical extrusion.
Completed Assembly
Large Counter
Monitor
Mount
Workstation Cabinet
*
*
*
**4
4A
5
S
E
G
Gra
p
h
i
c
Note: Monitor mount installs over SEG graphic.
Monitor Mount
Bolts
Monitor Mount Attachment
*
Attach Monitor Mount to horizontal extrusion
using bolts & wing nuts.
Wing
nuts
Z
14
0
Steps:
1) Attach cabinet to horizontal [4] using threaded stand-off caps.
See Cabinet to Horizontal Attachment detail.
2) Install Stand-Off Barrels to top of cabinet.
3) Attach lower shelf to pill slots located on horizontal [4].
See Custom Cam Lock w/ Pill Slot Attachment detail.
4) Set large Counter on top of stand-off barrels and
attach to pill slots in horizontal [4A].
See Custom Cam Lock w/ Pill Slot Attachment detail.
Small Counter
**
Workstation & Shelf Attachments
/
