Extron MTP T 15HD A User manual

MTP T 15HD A
Extron
Brand
Extron
Model
MTP T 15HD A
Category
AV extenders
Type
User manual

This manual is also suitable for

Extron MTP T 15HD A is a high-performance transmitter that extends video, audio, and control signals up to 330 feet (100 meters) over a single CATx cable. It supports resolutions up to 1920x1200, including widescreen formats, and provides exceptional image quality with advanced features like pre-peaking and adjustable peaking control. The MTP T 15HD A also includes a built-in EDID Minder that allows you to store and recall EDID information from connected displays.

Extron MTP T 15HD A is a high-performance transmitter that extends video, audio, and control signals up to 330 feet (100 meters) over a single CATx cable. It supports resolutions up to 1920x1200, including widescreen formats, and provides exceptional image quality with advanced features like pre-peaking and adjustable peaking control. The MTP T 15HD A also includes a built-in EDID Minder that allows you to store and recall EDID information from connected displays.

1
Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
Tie
Wrap
POWER
12V
0.5A MAX
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
MTP 15HD A Series • Setup Guide
This guide provides instructions for an installer to set up and operate
any of the Extron MTP 15HD A transmitters and receivers.
Installation
1. Turn off all MTPs and devices.
Turn the input and output devices off and unplug their power
cords. Verify that all MTPs are disconnected from the power
sources before proceeding.
2. Connect the transmitter inputs.
• Connect a VGA video source to the Input connector (
b
)
• Connect a VGA monitor to the Monitor connector (
c
)
• Connect a 3.5 mm stereo audio plug into the Audio connector (
d
).
Wire the plug as shown in gure 2.
3. Terminate and connect TP cables between units.
• Connect a TP cable between the Output connector (
f
) of the transmitter and the Input
connector (
g
) of the receiver. Terminate the cable ends identically with either standard as
shown in gure 3.
• For daisy-chaining, connect up to eight receivers using TP cables between the Buffered
Output connector (
h
) of a receiver and the Input connector (
g
) of a daisy-chained receiver.
4. Connect the receiver outputs.
• Connect a VGA display to the Output connector (
i
)
• Connect a 3.5 mm, 5-pole captive screw audio connector into the Mono Audio
connector (
j
) for two mono audio outputs. Wire the connector as shown in gure 4.
ATTENTION: Connect the sleeves to the ground (G). Connecting the sleeves
to a negative (–) terminal will damage the audio output circuits.
5. Configure the receiver DIP switches.
See figure 5 for DIP switch (located on the front panel of the receiver) layout and settings.
• H Sync + and V Sync + switches — Set these switches On (up) for positive sync or Off
(down) for negative sync.
• S-Video switch — Set this switch ON (up) to output chroma on pin 3 and luma on pin 2.
Set this switch OFF (down) to output chroma on pin 1 and luma on pin 2.
• End Unit switch — Set this switch On (up) if either of the following is true:
• The receiver being congured is the only receiver connected
to the transmitter.
• The receiver being congured is the last receiver in a daisy-chained system.
Set the End Unit switch Off (down) on the receiver being congured if there are one or
more receivers connected to the Buffered Output RJ-45 connector.
6. Terminate the power cable and ground the unit.
ATTENTION: See “Power Supply Wiring” in the user guide before wiring.
Wire the 2-pole captive screw connectors as shown in gure 6. Plug them into the Power connectors (
a
)
of the MTPs. The LED indicator on each MTP should be on when receiving power.
Grounding guidelines:
Extron MTP 15HD A products can be adversely affected by electrostatic discharge
(ESD)
if they are not
grounded
corr
ectly
.
To prevent malfunctions or product damage, an installer can correctly ground an Extron MTP 15HD A series
product by grounding the power input port. Insert one end of the grounding wire to the negative
or
ground pin
on the power input connector
(see
gure 6). Tie the other end of
the
wir
e
to an earth
ground.
If you have any questions about how to ground a product in a specic application, contact an Extron
technical
support
specialist.
Sleeve ( )
Ring
Right (
-
)
Tip
Left (+)
Figure 1. Transmitter and Receiver Rear Panels
Figure 2. Stereo Audio Plug
OUTPUT
INPUT
AUDIO
POWER
12V
.5A MAX
MONITOR
PRE-PEAK
ON
OFF
MTP T 15HD A
INPUT
BUFFERED
OUTPUT
OUTPUTS
RGB
POWER
12V
.5A MAX
MTP RL 15HD A
L
MONO AUDIO
R
651 32
4
1
7 8 9
10
12345678
Insert Twisted
Pair Wires
Pins:
NOTE: If you are using Enhanced Skew-Free™
A/V cable, use the TIA/EIA T568A standard only.
Pin
1
2
3
4
5
6
7
8
T568A
Wire Color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
T568B
Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Figure 3. TP Termination
MONO AUDIO
MONO AUDIO
Unbalanced Output
Balanced Output
Do not tin the wires!
Tip
Ring
Tip
Ring
Sleeves
LR
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
Figure 4. Captive Screw
Connector
ON
1 2 3 4 5
H SYNC +
V SYNC +
S-VIDEO
END UNIT
SPARE
Figure 5. DIP Switches
Figure 6. Power Wiring
and Grounding
2
MTP 15HD A • Setup Guide (Continued)
68-2206-50
Rev. B
03 13
7. Configure EDID
See the “EDID Minder” section for instructions on configuring EDID.
8. Adjust level and peaking.
• Pre-Peak switch (transmitter) — View the image and set the Pre-Peaking switch (
e
).
Set this switch to On (up) to compensate for long cable runs of the entire system.
• Level control (receiver) — View the image and adjust the Level control (see gure 7).
Full counterclockwise is minimum level.
• Peaking control (receiver) — View the image and adjust the Peaking control (see gure 7).
Full counterclockwise is zero peaking.
9. Adjust skew delay control (SEQ receivers).
Adjust the skew delay as follows (see gure 8):
a. Zero the skew delay for red, green, and blue by using a small screwdriver to press and hold the
Select button for 3 seconds. When the red, green, and blue LEDs all go out, release the Select button.
b. Use UTP cable test equipment or examine the displayed image to determine which video signal
(red, green, or blue) is shifted furthest to the left.
c. Select the furthest left video signal by using a small screwdriver to press and release the
Select button until the LED for the left-shifted color lights.
d. Slowly rotate the Delay knob clockwise until the selected color is converged.
e. If the remaining colors are left shifted, repeat steps b through d.
10. Mount the MTPs.
If necessary, mount the MTPs. For mounting information, see the MTP 15HD A Series User Guide.
EDID Minder
To use factory-installed EDID information or the user-recorded EDID:
1. If you have not already done so, connect the source device to the MTP 15HD transmitter.
Do not power on the source device at this time.
2. Set the front panel DIP switch (
c
) to the required frequency (50 or 60 Hz).
3. Set the rotary dial (
d
) to the required position (see the table to the right). Positions 1
through E are factory installed. Position 0 is for user-recorded EDID information. Position
F passes the EDID from the display connected to the Monitor loop-through port on the
transmitter back to the input.
To record EDID information from a specific monitor:
1. Turn the EDID Select dial (
d
) to position 0.
NOTE: The frequency DIP switch position (
c
) has no effect in this mode.
2. Connect a display to the Monitor connector on the transmitter.
NOTE: The MTP 15HD RS transmitter should be supplying the necessary
5 VDC to power on the display. However, to ensure that EDID is being
transmitted, power on the display.
3. Press and release the recessed Record button (
b
) to begin the recording process. The
Record LED (
a
) flashes red rapidly during recording, then returns to solid green after
recording is completed. At this time, the display can be disconnected. Connect the source
device to the input connector.
4. Power on or restart the source device.
MTP SERIES
50 Hz
RECORD
60 Hz SPARE
EDID
SELECT
ON
1
3
42
Figure 8. Skew Delay Control
Figure 9. MTP Transmitter Front Panel
DELAY
RED
GREEN
BLUE
SELECT
Rotary Switch
Position
Resolution
0 User-recorded EDID
1 800x600
2 1024x768 (default)
3 1280x720
4 1280x768
5 1280x800
6 1280x1024
7 1360x768
8 1366x768
9 1400x1050
A 1400x900
B 1600x1200
C 1680x1050
D 1920x1080
E 1920x1200
F Local monitor pass-through
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
R
G
B
PEAKING
LEVEL
Figure 7. Level and Peaking
  • Page 1 1
  • Page 2 2

Extron MTP T 15HD A User manual

MTP T 15HD A
Extron
Brand
Extron
Model
MTP T 15HD A
Category
AV extenders
Type
User manual
This manual is also suitable for

Extron MTP T 15HD A is a high-performance transmitter that extends video, audio, and control signals up to 330 feet (100 meters) over a single CATx cable. It supports resolutions up to 1920x1200, including widescreen formats, and provides exceptional image quality with advanced features like pre-peaking and adjustable peaking control. The MTP T 15HD A also includes a built-in EDID Minder that allows you to store and recall EDID information from connected displays.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents