Lexmark MS810 Series User manual

MS810 Series
Lexmark
Brand
Lexmark
Model
MS810 Series
Category
Laser/LED printers
Type
User manual
Quick Reference
Using the 2.4-inch display printer
model
Learning about the printer
Using the printer control panel
1
2
3
4
5
6
7
8
9
10
Use the To
1 Display
• View the printer status.
• Set up and operate the printer.
2 Select button Submit changes made in the printer settings.
3 Arrow
buttons
Scroll up and down or left and right.
4 Keypad Enter numbers, letters, or symbols.
Use the To
5 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep
mode:
• Press any hard button.
• Pull out Tray 1 or load paper in the
multipurpose feeder.
• Open a door or cover.
• Send a print job from the computer.
• Perform a power‑on reset with the main
power switch.
• Attach a device to the USB port on the
printer.
6 Stop or
Cancel button
Stop all printer activity.
7 Back button Return to the previous screen.
8 Home button Go to the home screen.
9 Indicator light Check the status of the printer.
10 USB port Connect a flash drive to the printer.
Note: Only the front USB port supports flash
drives.
Setting the paper size and type
1 From the printer control panel, navigate to:
> Settings > > Paper Menu > > Paper
Size/Type >
2 Press the up or down arrow button to select the tray or feeder, and
then press
.
3 Press the up or down arrow button to select the paper size, and
then press
.
4 Press the up or down arrow button to select the paper type, and
then press
to change the settings.
Configuring Universal paper settings
The Universal paper size is a user‑defined setting that lets you print on
paper sizes that are not preset in the printer menus.
Notes:
• The smallest supported Universal size is
70 x 127 mm (2.76 x 5 inches) for one‑sided printing and
105 x 148 mm (4.13 x 5.83 inches) for two‑sided (duplex)
printing.
• The largest supported Universal size is 216 x
356 mm (8.5 x 14 inches) for one‑sided and two‑sided printing.
From the printer control panel, navigate to:
> Settings > > Paper Menu > > Universal
Setup >
> Units of Measure > > select unit of
measure >
Adjusting toner darkness
Using the Embedded Web Server
1
Open a Web browser, and then type the IP address of the printer
in the address field.
Notes:
• View the printer IP address in the TCP/IP section in the
Network/Ports menu. The IP address appears as four sets of
numbers separated by periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Using the printer control panel
1
From the printer control panel, navigate to:
> Settings > > Print Settings > > Quality
Menu >
> Toner Darkness
2 Adjust the toner darkness, and then press .
1
Supported flash drives and file types
Flash drive File type
• Lexar JumpDrive 2.0 Pro (256MB, 512MB, or 1GB
sizes)
• SanDisk Cruzer Mini (256MB, 512MB, or 1GB sizes)
Notes:
• Hi‑speed USB flash drives must support the
full‑speed standard. Low-speed USB devices are
not supported.
• USB flash drives must support the File Allocation
Table (FAT) system. Devices formatted with New
Technology File System (NTFS) or any other file
system are not supported.
Documents:
• .pdf
• .xps
• .html
Images:
• .dcx
• .gif
• .JPEG
or .jpg
• .bmp
• .pcx
• .TIFF
or .tif
• .png
Printing from a flash drive
Notes:
• Before printing an encrypted PDF file, you will be prompted to
enter the file password from the printer control panel.
• You cannot print files for which you do not have printing
permissions.
1 Insert a flash drive into the USB port.
Notes:
• A flash drive icon appears on the printer control panel and in
the held jobs icon when a flash drive is installed.
• If you insert the flash drive when the printer requires
attention, such as when a jam has occurred, then the printer
ignores the flash drive.
• If you insert the flash drive while the printer is processing
other print jobs, then Busy appears. After these print jobs
are processed, you may need to view the held jobs list to
print documents from the flash drive.
Warning—Potential Damage: Do not touch the printer or the
flash drive in the area shown while actively printing, reading, or
writing from the memory device. Loss of data can occur.
2 From the printer control panel, select the document you want to
print.
3 Press the left or right arrow button to specify the number of copies
for printing, and then press
.
Notes:
• Do not remove the flash drive from the USB port until the
document has finished printing.
• If you leave the flash drive in the printer after leaving the
initial USB menu screen, then access held jobs from the
printer control panel to print files from the flash drive.
Canceling a print job from the printer control
panel
From the printer control panel, press > .
Linking and unlinking trays
1 Open a Web browser, and then type the printer IP address in the
address field.
Notes:
• View the printer IP address on the printer control panel in
the TCP/IP section under the Network/Ports menu. The IP
address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Paper Menu.
3 Change the paper size and type settings for the trays you are linking.
• To link trays, make sure the paper size and type for the tray
match that of the other tray.
• To unlink trays, make sure the paper size or type for the tray
does not match that of the other tray.
4 Click Submit.
Note: You can also change the paper size and type settings using the
printer control panel. For more information, see “Setting the paper
size and type” on page 1.
Warning—Potential Damage: Paper loaded in the tray should match
the paper type name assigned in the printer. The temperature of the
fuser varies according to the specified paper type. Printing issues
may occur if settings are not properly configured.
2
Using the 4.3-inch touch-screen
printer model
Learning about the printer
Using the printer control panel
1
2
3
4
5
6
7
Use the To
1 Display
• View the printer status.
• Set up and operate the printer.
2 Home button Go to the home screen.
3 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep
Mode:
• Press any hard button.
• Pull out Tray 1 or load paper in the
multipurpose feeder.
• Open a door or cover.
• Send a print job from the computer.
• Perform a power‑on reset with the main
power switch.
• Attach a device to the USB port on the
printer.
4 Keypad Enter numbers, letters, or symbols.
Use the To
5 Stop or
Cancel
button
Stop all printer activity.
6 Indicator
light
Check the status of the printer.
7 USB port Connect a flash drive to the printer.
Note: Only the front USB port supports flash
drives.
Understanding the home screen
When the printer is turned on, the display shows a basic screen,
referred to as the home screen. Use the home screen buttons and icons
to initiate an action.
Note: Your home screen may vary depending on your home screen
customization settings, administrative setup, and active embedded
solutions.
1
2
3
4
5
6
7
8
Touch To
1 Change Language Change the primary language of the printer.
2 Bookmarks Create, organize, and save a set of
bookmarks (URLs) into a tree view of folders
and file links.
Note: The tree view does not include
bookmarks created within Forms and
Favorites, and the ones in the tree are not
usable in Forms and Favorites.
Touch To
3 Held Jobs Display all current held jobs.
4 USB View, select, or print photos and documents
from a flash drive.
Note: This icon appears only when you
return to the home screen while a memory
card or flash drive is connected to the
printer.
5 Menus Access printer menus.
Note: These menus are available only
when the printer is in ready state.
6 Status message
bar
• Show the current printer status such as
Ready or Busy.
• Show printer conditions such as
Imaging unit low or Cartridge
Low.
• Show intervention messages and the
instructions on how to clear them.
7 Status/Supplies
• Show a printer warning or error
message whenever the printer requires
intervention to continue processing.
• View more information on the printer
warning or message, and on how to
clear it.
8 Tips View a context‑sensitive help information.
This may also appear on the home screen:
Touch To
Search Held Jobs Search current held jobs.
Jobs by user Access print jobs saved by user.
Profiles and
Solutions
Access profiles and solutions.
Features
Feature Description
Attendance message
alert
If an attendance message affects a function,
then this icon appears and the red indicator light
blinks.
3
Feature Description
Warning
If an error condition occurs, then this icon
appears.
Printer IP address
Example:
123.123.123.12
3
The IP address of your printer is located at the
top left corner of the home screen and appears
as four sets of numbers separated by periods.
You can use the IP address when accessing the
Embedded Web Server to view and remotely
configure printer settings even when you are not
physically near the printer.
Using the touch-screen buttons
Note: Your home screen may vary, depending on your home screen
customization settings, administrative setup, and active embedded
solutions.
1
2
3
4
5
Touch the To
1 Radio button Select or clear an item.
2 Up arrow Scroll up.
3 Down arrow Scroll down.
4 Accept button Save a setting.
Touch the To
5 Cancel button
• Cancel an action or a selection.
• Return to the previous screen.
Other touch-screen buttons
Touch To
Return to the home screen.
Open a context-sensitive Help dialog on the
printer control panel.
Scroll to the left.
Scroll to the right.
Setting the paper size and type
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper
size or type >
Configuring Universal paper settings
The Universal paper size is a user‑defined setting that lets you print on
paper sizes that are not preset in the printer menus.
Notes:
• The smallest supported Universal size is
70 x 127 mm (2.76 x 5 inches) for one‑sided printing and
105 x 148 mm (4.13 x 5.83 inches) for two‑sided (duplex)
printing.
• The largest supported Universal size is 216 x
356 mm (8.5 x 14 inches) for one‑sided and two‑sided printing.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select
a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch .
Adjusting toner darkness
Using the Embedded Web Server
1
Open a Web browser, and then type the printer IP address in the
address field.
Notes:
• View the printer IP address on the printer home screen. The
IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the setting, and then click Submit.
Using the printer control panel
1
From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch .
4
Supported flash drives and file types
Flash drive File type
• Lexar JumpDrive 2.0 Pro (256MB, 512MB, or 1GB
sizes)
• SanDisk Cruzer Mini (256MB, 512MB, or 1GB sizes)
Notes:
• Hi‑speed USB flash drives must support the
full‑speed standard. Low-speed USB devices are
not supported.
• USB flash drives must support the File Allocation
Table (FAT) system. Devices formatted with New
Technology File System (NTFS) or any other file
system are not supported.
Documents:
• .pdf
• .xps
• .html
Images:
• .dcx
• .gif
• .JPEG
or .jpg
• .bmp
• .pcx
• .TIFF
or .tif
• .png
Printing from a flash drive
Notes:
• Before printing an encrypted PDF file, you will be prompted to
type the file password from the printer control panel.
• You cannot print files for which you do not have printing
permissions.
1 Insert a flash drive into the USB port.
Notes:
• A flash drive icon appears on the printer home screen when
a flash drive is inserted.
• If you insert the flash drive when the printer requires
attention, such as when a jam has occurred, then the printer
ignores the flash drive.
• If you insert the flash drive while the printer is processing
other print jobs, then Busy appears. After these print jobs
are processed, you may need to view the held jobs list to
print documents from the flash drive.
Warning—Potential Damage: Do not touch the printer or the
flash drive in the area shown while actively printing, reading, or
writing from the memory device. Loss of data can occur.
2 From the printer control panel, touch the document you want to
print.
3 Touch the arrows to specify the number of copies for printing, and
then touch Print.
Notes:
• Do not remove the flash drive from the USB port until the
document has finished printing.
• If you leave the flash drive in the printer after leaving the
initial USB menu screen, then touch Held Jobs on the home
screen to print files from the flash drive.
Canceling a print job from the printer control
panel
1 From the printer control panel, touch Cancel Jobs or press
on the keypad.
2 Touch the print job you want to cancel, and then touch Delete
Selected Jobs.
Linking and unlinking trays
1 Open a Web browser, and then type the printer IP address in the
address field.
Notes:
• View the printer IP address on the printer home screen. The
IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Paper Menu.
3 Change the paper size and type settings for the trays you are linking.
• To link trays, make sure the paper size and type for the tray
match that of the other tray.
• To unlink trays, make sure the paper size or type for the tray
does not match that of the other tray.
4 Click Submit.
Note: You can also change the paper size and type settings using the
printer control panel. For more information, see “Setting the paper
size and type” on page 4.
Warning—Potential Damage: Paper loaded in the tray should match
the paper type name assigned in the printer. The temperature of the
fuser varies according to the specified paper type. Printing issues
may occur if settings are not properly configured.
5
Using the 7-inch touch-screen
printer model
Learning about the printer
Using the printer control panel
4
1
2
3
5
6
7
Use the To
1 Display
• View the status of the printer.
• Set up and operate the printer.
2 Home button Go to the home screen.
3 Sleep button Enable Sleep mode or Hibernate mode.
Do the following to wake the printer from Sleep
mode:
• Press and release the Sleep button.
• Touch the screen or press any hard button.
• Open a tray, cover, or door.
• Send a print job from the computer.
• Perform a power‑on reset with the main
power switch.
• Attach a device to a USB port.
4 Keypad Enter numbers, letters, or symbols on the
printer.
Use the To
5 Stop or
Cancel
button
Stop all printer activity.
6 Indicator
light
Check the status of the printer.
7 USB port Connect a USB Bluetooth adapter or a flash drive
to the printer.
Note: Only the front USB port supports flash
drives.
Understanding the home screen
When the printer is turned on, the display shows a basic screen,
referred to as the home screen. Use the home screen buttons and icons
to initiate an action.
Note: Your home screen may vary depending on your home screen
customization settings, administrative setup, and active embedded
solutions.
1
2
3
4
5
6
7
8
Touch To
1 Search Held Jobs Search current held jobs.
2 Held Jobs Display all current held jobs.
3 Forms and
Favorites
Access frequently used online forms.
Touch To
4 Eco‑Settings Adjust energy consumption, noise, toner
and paper usage.
5 Menus Access printer menus.
Note: These menus are available only
when the printer is in Ready state.
6 Status message bar
• Show the current printer status such
as Ready or Busy.
• Show printer conditions such as
Imaging unit low or
Cartridge Low.
• Show intervention messages and the
instructions on how to clear them.
7 Status/Supplies
• Show a printer warning or error
message whenever the printer
requires intervention to continue
processing.
• View more information on the printer
warning or message, and on how to
clear it.
8 Tips Open a context‑sensitive Help information
on the printer control panel.
Features
Feature Description
Attendance message
alert
If an attendance message affects a function,
then this icon appears and the red indicator light
blinks.
Warning
If an error condition occurs, then this icon
appears.
Printer IP address
Example:
123.123.123.12
3
The IP address of your network printer is located
at the top left corner of the home screen and
appears as four sets of numbers separated by
periods. You can use the IP address when
accessing the Embedded Web Server so you can
view and remotely configure printer settings
even when you are not physically near the
printer.
6
Using the touch-screen buttons
Note: Your home screen, icons, and buttons may vary, depending on
your home screen customization settings, administrative setup, and
active embedded solutions.
1
2
3
4
5
6
7
8
Touch To
1 Left arrow
Scroll to the left.
2 Right arrow
Scroll to the right.
3 Up arrow
Scroll up.
Touch To
4 Down arrow
Scroll down.
5 Submit Submit changes made in the printer settings.
6Back Return to the previous screen.
7 Home
Return to the home screen.
8 Tips
Open a context-sensitive Help dialog on the
printer control panel.
Other touch-screen buttons
Touch To
Accept
Save settings.
Cancel
• Cancel an action or a selection.
• Leave a screen and return to the previous
screen without saving changes.
Increase
Select a higher value.
Touch To
Decrease
Select a lower value.
Exit Leave the current screen.
Search Search current held jobs.
Warning
View a warning or error message.
Setting the paper size and type
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select a paper
size or type > Submit
Notes:
• The paper size is automatically set according to the position of
the paper guides in each tray except the multipurpose feeder.
• The paper size for the multipurpose feeder must be set manually
from the Paper Size menu.
• The paper type must be set manually for all trays that do not
contain plain paper.
Configuring Universal paper settings
Universal paper size is a user‑defined setting that lets you print on
paper sizes that are not preset in the printer menus.
7
Notes:
• The smallest supported Universal size is
70 x 127 mm (2.76 x 5 inches) for one‑sided printing and
105 x 148 mm (4.13 x 5.83 inches) for two‑sided (duplex)
printing.
• The largest supported Universal size is 216 x
356 mm (8.5 x 14 inches) for one‑sided and two‑sided printing.
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select
a unit of measure
2 Touch Portrait Width or Portrait Height.
3 Select the width or height, and then touch Submit.
Adjusting toner darkness
1 Open a Web browser, and then type the printer IP address in the
address field.
Notes:
• View the printer IP address on the printer home screen. The
IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
3 Adjust the toner darkness, and then click Submit.
Using the printer control panel
1
From the home screen, navigate to:
> Settings > Print Settings > Quality Menu > Toner Darkness
2 Adjust the setting, and then touch Submit.
Supported flash drives and file types
Flash drive File type
• Lexar JumpDrive 2.0 Pro (256MB, 512MB, or 1GB
sizes)
• SanDisk Cruzer Mini (256MB, 512MB, or 1GB sizes)
Notes:
• High‑speed USB flash drives must support the
full‑speed standard. Low-speed USB devices are
not supported.
• USB flash drives must support the FAT (File
Allocation Tables) system. Devices formatted with
NTFS (New Technology File System) or any other
file system are not supported.
Documents:
• .pdf
• .xps
• .html
Images:
• .dcx
• .gif
• .JPEG
or .jpg
• .bmp
• .pcx
• .TIFF or .tif
• .png
Printing from a flash drive
Notes:
• Before printing an encrypted PDF file, you will be prompted to
type the file password from the printer control panel.
• You cannot print files for which you do not have printing
permissions.
1 Insert a flash drive into the USB port.
Notes:
• A flash drive icon appears on the printer home screen when
a flash drive is inserted.
• If you insert the flash drive when the printer requires
attention, such as when a jam has occurred, then the printer
ignores the flash drive.
• If you insert the flash drive while the printer is processing
other print jobs, then Busy appears. After these print jobs
are processed, you may need to view the held jobs list to
print documents from the flash drive.
Warning—Potential Damage: Do not touch the USB cable, any
wireless network adapter, any connector, the memory device, or
the printer in the areas shown while actively printing, reading, or
writing from the memory device. Loss of data can occur.
2 From the printer control panel, touch the document you want to
print.
3 Touch the arrows to specify the number of copies for printing, and
then touch Print.
Notes:
• Do not remove the flash drive from the USB port until the
document has finished printing.
• If you leave the flash drive in the printer after leaving the
initial USB menu screen, then touch Held Jobs on the home
screen to print files from the flash drive.
8
Canceling a print job from the printer control
panel
1 Touch Cancel Jobs on the printer control panel, or press on
the keypad.
2 Touch the print job you want to cancel, and then touch Delete
Selected Jobs.
Linking and unlinking trays
1 Open a Web browser, and then type the printer IP address in the
address field.
Notes:
• View the printer IP address on the printer home screen. The
IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the Web page correctly.
2 Click Settings > Paper Menu.
3 Change the paper size and type settings for the trays you are linking.
• To link trays, make sure the paper size and type for the tray
match that of the other tray.
• To unlink trays, make sure the paper size or type for the tray
does not match that of the other tray.
4 Click Submit.
Note: You can also change the paper size and type settings using the
printer control panel. For more information, see “Setting the paper
size and type” on page 7.
Warning—Potential Damage: Paper loaded in the tray should match
the paper type name assigned in the printer. The temperature of the
fuser varies according to the specified paper type. Printing issues
may occur if settings are not properly configured.
Using the 4.3- and 7-inch touch
screens
Setting up and using the home screen
applications
Notes:
• Your home screen, icons, and buttons may vary depending on
your home screen customization settings, administrative setup,
and active embedded applications. Some applications are
supported only on select printer models.
• There may be additional solutions and applications available for
purchase. To learn more, visit
www.lexmark.com. Or, inquire at
your point of purchase.
Accessing the Embedded Web Server
The Embedded Web Server is the printer Web page that lets you view
and remotely configure printer settings even when you are not
physically near the printer.
1 Obtain the printer IP address:
• From the printer control panel home screen
• From the TCP/IP section in the Network/Ports menu
• By printing a network setup page or menu settings page, and
then finding the TCP/IP section
Note: An IP address appears as four sets of numbers separated
by periods, such as 123.123.123.123.
2 Open a Web browser, and then type the printer IP address in the
address field.
The Embedded Web Server page appears.
Customizing the home screen
1 Open a Web browser, and then type the printer IP address in the
address field.
Note: View the printer IP address on the printer home screen.
The IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
2 Do one or more of the following:
• Show or hide icons of basic printer functions.
a Click Settings > General Settings > Home screen
customization.
b Select the check boxes to specify which icons appear on the
printer home screen.
Note: If you clear a check box beside an icon, then the
icon does not appear on the home screen.
c Click Submit.
• Customize the icon for an application. For more information,
see “Finding information about the home screen applications”
on page 9 or see the documentation that came with the
application.
Activating the home screen applications
Your printer comes with preinstalled home screen applications. Before
you can use these applications, first activate and set up these
applications using the Embedded Web Server. For more information
about accessing the Embedded Web Server, see “Accessing the
Embedded Web Server” on page 9.
For detailed information about configuring and using the home screen
applications, visit the Lexmark Web site at
www.lexmark.com.
Finding information about the home screen applications
Your printer comes with preinstalled home screen applications. Before
you can use these applications, first activate and set up these
applications using the Embedded Web Server. For more information
on accessing the Embedded Web Server, see “Accessing the Embedded
Web Server” on page 9.
For more information on configuring and using the home screen
applications, do the following:
1 Go to http://support.lexmark.com, and then click SELECT YOUR
PRODUCT >
.
2 Do either of the following:
• Click Business Solutions, and then select the name of the
application.
• Click Software and Solutions > Other Apps.
3 Click the Manuals tab, and then select the document for the home
screen application.
9
Using Background and Idle Screen
Use To
Customize the background and idle screen of
your printer home screen.
From the home screen, navigate to:
Change Background > select background to use > Apply
Setting up Forms and Favorites
Use To
Simplify and streamline work processes by
letting you quickly find and print frequently
used online forms directly from the printer
home screen.
Note: The printer must have permission to
access the network folder, FTP site, or Web
site where the bookmark is stored. From the
computer where the bookmark is stored, use
sharing, security, and firewall settings to
allow the printer at least a read access. For
more information, see the documentation
that came with your operating system.
1 Open a Web browser, and then type the printer IP address in the
address field.
Note: View the printer IP address on the printer home screen.
The IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
2 Click Settings > Apps > Apps Management > Forms and Favorites.
Note: Navigate through form categories, or search for forms
based on a form number, name, or description.
3 Define the bookmarks, and then customize the settings.
4 Click Apply.
Setting up Remote Operator Panel
This application shows the printer control panel on your computer
screen and lets you interact with the printer control panel, even when
you are not physically near the network printer. From your computer
screen, you can view the printer status, release held print jobs, create
bookmarks, and do other print-related tasks you might normally
perform on the network printer.
1 Open a Web browser, and then type the printer IP address in the
address field.
Note: View the printer IP address on the printer home screen.
The IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
2 Click Settings > Remote Operator Panel Settings.
3 Select the Enabled check box, and then customize the settings.
4 Click Submit.
To use the application, click Remote Operator Panel > Launch VNC
Applet.
Understanding Eco‑Settings
Use To
Manage energy consumption, noise, toner,
and paper usage settings to help reduce the
environmental impact of your printer.
Exporting and importing a configuration
You can export configuration settings into a text file, and then import
it to apply the settings to other printers.
1 Open a Web browser, and then type the printer IP address in the
address field.
Note: View the printer IP address on the printer home screen.
The IP address appears as four sets of numbers separated by
periods, such as 123.123.123.123.
2 Click Settings > Apps > Apps Management.
3 From the list of installed applications, click the name of the
application you want to configure.
4 Click Configure, and then do one of the following:
• To export a configuration to a file, click Export, and then follow
the instructions on the computer screen to save the
configuration file.
Notes:
– When saving the configuration file, you can type a
unique file name or use the default name.
– If a JVM Out of Memory error occurs, then repeat
the export process until the configuration file is saved.
• To import a configuration from a file, click Import, and then
browse to the saved configuration file that was exported from
a previously configured printer.
Notes:
– Before importing the configuration file, you can choose
to preview it first or load it directly.
– If a timeout occurs and a blank screen appears, then
refresh the Web browser, and then click Apply.
Printing
Printing a document
1 From the printer control panel, set the paper type and size to match
the paper loaded.
2 Send the print job:
For Windows users
a With a document open, click File > Print.
b Click Properties, Preferences, Options, or Setup.
c Adjust the settings, if necessary.
d Click OK > Print.
For Macintosh users
a Customize the settings in the Page Setup dialog:
1 With a document open, choose File > Page Setup.
2 Choose a paper size or create a custom size to match the
paper loaded.
3 Click OK.
b Customize the settings in the Print dialog:
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more
options.
10
2 From the print options pop‑up menus, adjust the settings,
if necessary.
Note: To print on a specific paper type, adjust the
paper type setting to match the paper loaded, or select
the appropriate tray or feeder.
3 Click Print.
Canceling a print job from the computer
For Windows users
1 Open the printers folder:
a Click , or click Start and then click Run.
b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
For Macintosh users
In Mac OS X version 10.5 or later:
1 From the Apple Menu, navigate to either of the following:
• System Preferences > Print & Fax > select a printer > Open Print
Queue
• System Preferences > Print & Scan > select a printer > Open
Print Queue
2 From the printer window, select the print job you want to cancel,
and then click Delete.
Loading paper and specialty
media
Loading paper and specialty media
Loading the 250‑ or 550‑sheet tray
CAUTION—POTENTIAL INJURY: To reduce the risk of
equipment instability, load each tray separately. Keep all other
trays closed until needed.
1 Pull out the tray.
Notes:
• When loading folio‑, legal‑, or oficio‑size paper, lift the tray
slightly and pull it out.
• Avoid removing trays while a job prints or while Busy
appears on the display. Doing so may cause a jam.
2 Squeeze and slide the width guide to the correct position for the
size of the paper being loaded until it clicks into place.
2
1
Note: Use the paper size indicators on the bottom of the tray to
help position the guides.
11
3 Unlock the length guide, and then squeeze and slide the guide to
the correct position for the size of the paper being loaded.
3
1
2
Notes:
• Lock the length guide for all paper sizes.
• Use the paper size indicators on the bottom of the tray to
help position the guides.
4 Flex the sheets back and forth to loosen them. Do not fold or crease
the paper. Straighten the edges on a level surface.
5 Load the paper stack with the printable side facedown.
Note: Make sure the paper or envelope is loaded properly.
• There are different ways for loading letterhead depending on
whether an optional staple finisher is installed or not.
12
Without an optional staple finisher With an optional staple finisher
ABC
One‑sided printing One‑sided printing
A
B
C
Two‑sided printing
ABC
Two‑sided printing
• Do not slide the paper into the tray. Load paper as shown in the
illustration.
• If you are loading envelopes, then make sure that the flap side
is facing up and the envelopes are on the left side of the tray.
• Make sure the paper is below the maximum paper fill indicator.
Warning—Potential Damage: Overfilling the tray can cause
paper jams.
6 For custom‑ or universal‑size paper, adjust the paper guides to
lightly touch the sides of the stack, and then lock the length guide.
13
7 Insert the tray.
8 From the printer control panel, set the paper size and type in the
Paper menu to match the paper loaded in the tray.
Note: Set the correct paper size and type to avoid paper jams
and print quality problems.
Loading the 2100‑sheet tray
CAUTION—POTENTIAL INJURY: To reduce the risk of
equipment instability, load each tray separately. Keep all other
trays closed until needed.
1 Pull out the tray.
2 Adjust the width and length guides.
Loading A5‑size paper
a
Pull up and slide the width guide to the position for A5.
L
G
L
O
F
C
F
O
L
I
O
LT
R
A
4
A
5
1
LG
L
O
FC
FO
L
IO
LT
R
A
4
A
5
2
L
G
L
O
F
C
F
O
L
IO
LT
R
A
4
A
5
b Squeeze and slide the length guide to the position for A5 until
it clicks into place.
1
2
14
c Remove the A5 length guide from its holder.
1
2
d Insert the A5 length guide into its designated slot.
Note: Press the A5 length guide until it clicks into place.
Loading A4‑, letter‑, legal‑, oficio‑, and folio‑size paper
a
Pull up and slide the width guide to the correct position for the
size of the paper being loaded.
L
G
L
O
F
C
F
O
L
I
O
LT
R
A
4
A
5
1
L
G
L
O
F
C
F
O
L
I
O
LT
R
A4
A5
2
L
G
L
O
F
C
F
O
L
I
O
LT
R
A
4
A
5
b If the A5 length guide is still attached to the length guide, then
remove it from its place. If the A5 length guide is not attached,
then proceed to step d.
c Put the A5 length guide in its holder.
2
1
15
d Squeeze the length guide and slide it to the correct position for
the size of the paper being loaded until it clicks into place.
3 Flex the sheets back and forth to loosen them. Do not fold or crease
the paper. Straighten the edges on a level surface.
4 Load the paper stack with the printable side facedown.
Note: Make sure the paper is loaded properly.
• There are different ways for loading letterhead depending on
whether an optional staple finisher is installed or not.
Without an optional staple finisher With an optional staple finisher
ABC
One‑sided printing
ABC
One‑sided printing
A
B
C
Two‑sided printing
A
B
C
Two‑sided printing
• Make sure the paper is below the maximum paper fill indicator.
Warning—Potential Damage: Overfilling the tray can cause
paper jams.
5 Insert the tray.
Note: Press the paper stack down while inserting the tray.
16
6 From the printer control panel, set the size and type in the Paper
menu to match the paper loaded in the tray.
Note: Set the correct paper size and type to avoid paper jams
and print quality problems.
Loading the multipurpose feeder
1 Pull down the multipurpose feeder door.
Note: Do not load or close the multipurpose feeder while a job is
printing.
B
5
E
X
E
C
A
4
A
5
LT
R
2 Pull the multipurpose feeder extender.
B
5
E
X
E
C
A
4
A
5
LT
R
Note: Guide the extender gently so that the multipurpose feeder
is fully extended and open.
3 Slide the width guide to the correct position for the size of the paper
being loaded.
B5
E
X
E
C
A
4
A
5
LT R
Note: Use the paper size indicators on the bottom of the tray to
help position the guides.
17
B
5
E
X
E
C
A
4
A
5
LT
R
4 Prepare the paper or specialty media for loading.
• Flex sheets of paper back and forth to loosen them. Do not fold
or crease the paper. Straighten the edges on a level surface.
• Hold transparencies by the edges. Straighten the edges on a
level surface.
Note: Avoid touching the printable side of the
transparencies. Be careful not to scratch them.
• Flex the stack of envelopes back and forth to loosen them.
Straighten the edges on a level surface.
5 Load the paper or specialty media.
Note: Slide the stack gently into the multipurpose feeder until it
comes to a stop.
• Load only one size and type of paper or specialty media at a
time.
• Make sure the paper fits loosely in the multipurpose feeder,
lies flat, and is not bent or wrinkled.
• There are different ways of loading letterhead depending on
whether an optional staple finisher is installed or not.
Without an optional staple finisher With an optional staple finisher
ABC
One‑sided printing
ABC
One‑sided printing
Without an optional staple finisher With an optional staple finisher
ABC
Two‑sided (duplex) printing
Two‑sided (duplex) printing
• Load envelopes with the flap side down and on the left of the
multipurpose feeder.
B
5
EXE
C
A
4
A
5
LT
R
Warning—Potential Damage: Never use envelopes with
stamps, clasps, snaps, windows, coated linings, or self‑stick
adhesives. These envelopes may severely damage the
printer.
18
• Make sure the paper or specialty media is below the maximum
paper fill indicator.
Warning—Potential Damage: Overfilling the feeder can
cause paper jams.
6 For custom- or universal-size paper, adjust the width guides to
lightly touch the sides of the stack.
7 From the printer control panel, set the paper size and type in the
Paper menu to match the paper loaded in the tray.
Note: Set the correct paper size and type to avoid paper jams
and print quality problems.
Clearing jams
Carefully select paper and specialty media, and then load them
properly to avoid most jams. For more information, see “Avoiding
jams” on page 19. If jams occur, then follow the steps outlined in this
chapter.
Note: Jam recovery is set to Auto by default. The printer reprints
jammed pages unless the memory required to hold the pages is
needed for other printer tasks.
Avoiding jams
Load paper properly
• Make sure paper lies flat in the tray.
Correct loading of paper Incorrect loading of paper
• Do not remove a tray while the printer is printing.
• Do not load a tray while the printer is printing. Load it before
printing, or wait for a prompt to load it.
• Do not load too much paper. Make sure the stack height is below
the maximum paper fill indicator.
• Do not slide the paper into the tray. Load paper as shown in the
illustration.
• Make sure the guides in the tray or the multipurpose feeder are
properly positioned and are not pressing tightly against the paper
or envelopes.
• Push the tray firmly into the printer after loading paper.
• If you are loading prepunched paper for use with the staple finisher,
then make sure the holes on the long edge of the paper are on the
right side of the tray.
Source Printing Orientation
Tray One‑sided The short edge with holes enters
the printer first.
Two‑sided The short edge without holes
enters the printer first.
Multipurpose
feeder
One‑sided The short edge with holes enters
the printer first.
Two‑sided The short edge without holes
enters the printer first.
Note: If the holes on the long edge of the paper are on the left
side of the tray, then a jam may occur.
19
Allow the paper to enter the optional mailbox bins
properly
• Make sure to adjust the bin extender so that the paper size
indicators match the size of the paper used.
Notes:
– If the bin extender is shorter than the size of the paper you
are printing on, then the paper causes a jam in the mailbox
bin. For example, if you are printing on a legal-size paper and
the bin extender is set to letter-size, then a jam occurs.
– If the bin extender is longer than the size of the paper you
are printing on, then the edges become uneven and the
paper is not stacked properly. For example, if you are
printing on a letter-size paper and the bin extender is set to
legal-size, then the paper does not stack properly.
• If paper needs to be returned to the mailbox bin, then insert the
paper under the bin arm, and then push the paper all the way back.
1
2
Note: If the paper is not under the bin arm, then a jam occurs
due to an overfilled bin.
Use recommended paper
• Use only recommended paper or specialty media.
• Do not load wrinkled, creased, damp, bent, or curled paper.
• Flex and straighten paper before loading it.
• Do not use paper that has been cut or trimmed by hand.
• Do not mix paper sizes, weights, or types in the same tray.
• Make sure the paper size and type are set correctly on the computer
or printer control panel.
• Store paper per manufacturer recommendations.
Understanding jam messages and
locations
When a jam occurs, a message indicating the jam location and
information to clear the jam appears on the printer display. Open the
doors, covers, and trays indicated on the display to remove the jam.
Notes:
• When Jam Assist is set to On, Discarding pages appears
on the display and the printer flushes blank or pages with partial
prints to the standard bin after a jammed page is cleared. Check
your printed output for blank pages.
• When Jam Recovery is set to On or Auto, the printer reprints
jammed pages. However, the Auto setting reprints jammed
pages if adequate printer memory is available.
2
3
4
5
6
7
8
9
11
1
10
Jam location Printer message What to do
1 Staple finisher [x]‑page jam,
remove paper, open
stapler door. Leave
paper in bin. [455–
457]
Remove paper from
the stapler bin, open
the stapler door, then
remove the staple
cartridge, and then
remove the jammed
staples.
2 Standard bin [x]‑page jam,
remove standard bin
jam. [203]
Remove jammed
paper from the
standard bin.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

Lexmark MS810 Series User manual

MS810 Series
Lexmark
Brand
Lexmark
Model
MS810 Series
Category
Laser/LED printers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents