Mec 3247ES Operating instructions

Category
Floor Machine
Type
Operating instructions

This manual is also suitable for

This Operator’s Manual
MUST BE READ AND UNDERSTOOD
prior to operating your
MEC Aerial Work Platform
OPERATOR’S MANUAL
Part # 91087 Rev1
Issued April 2007
1532ES / 1932ES
2033ES / 2633ES
2047ES / 2647ES /
3247ES
Serial Number Range
1532ES: 9001100 - Present
1932ES: 9015000 - Present
2033ES: 8804100 - Present
2633ES: 11100600 - Present
2047ES: 9801100 - Present
2647ES: 9901200 - Present
3247ES: 10001200 - Present
Page i
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
TABLE OF CONTENTS
Introduction ..................................................................................................................... iii
Machine Specifications ................................................................................................... iv
SECTION 1: SAFETY ............................................................................................................ 1-1
Safety Rules And Precautions ..................................................................................... 1-2
Safety Symbols ............................................................................................................ 1-4
Fall Protection Notice ................................................................................................... 1-6
Safety And Control Decal Locations - 32 Series .......................................................... 1-8
Safety And Control Decal Locations - 33 Series .........................................................1-10
Safety And Control Decal Locations - 47 Series .........................................................1-12
SECTION 2: OPERATION ..................................................................................................... 2-1
Transport and Lifting Instructions ................................................................................. 2-2
Unloading Procedures ................................................................................................. 2-3
Primary Machine Components .................................................................................... 2-4
Operator Controls ........................................................................................................ 2-5
Safety .......................................................................................................................... 2-6
Platform Controls .............................................................................................. 2-9
Prestart Inspection .....................................................................................................2-10
Machine Start Up .............................................................................................2-10
Base Control Operation And Checks ...............................................................2-11
Platform Control Operation and Checks ..........................................................2-12
Operation ....................................................................................................................2-13
Driving and Steering ........................................................................................2-13
Braking.............................................................................................................2-14
Elevating The Platform .....................................................................................2-14
Lowering The Platform .....................................................................................2-14
Extending The Roll-out Extension Deck ...........................................................2-15
Lowering The Platform Railings .......................................................................2-15
Charging The Batteries ...............................................................................................2-16
Shutdown Procedure ..................................................................................................2-16
Moving The Machine...................................................................................................2-17
Towing/ Winching The Machine........................................................................2-17
Emergency Systems And Procedures ........................................................................2-18
Emergency Lowering
1532ES - 1932ES
2033ES - 2633ES
2047ES - 2647ES .......................................................................................................2-18
Emergency Lowering - 3247ES .......................................................................2-19
Page ii
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SECTION 3: MAINTENANCE ................................................................................................ 3-1
General Maintenance Tips ........................................................................................... 3-2
Prestart Inspection ...................................................................................................... 3-4
Frequent Inspection ..................................................................................................... 3-6
Annual Inspection ........................................................................................................ 3-7
Troubleshooting ........................................................................................................... 3-9
Lubrication Diagram ...................................................................................................3-10
Lubrication Chart ........................................................................................................3-11
Page iii
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
MEC Aerial Platform Sales Corp.
1775 Park Street, Suite 77. • Selma, CA 93662 USA
Ph: 1-800-387-4575 • 559-891-2488 • Fax: 559-891-2448
E-mail:[email protected] • Web:www.mecawp.com
INTRODUCTION
This Operator’s Manual has been designed to provide you, the customer, with the instructions
and operating procedures essential to properly and safely operate your MEC Self-Propelled
Scissors for its intended purpose of positioning personnel, along with their necessary tools and
materials to overhead work locations.
THE OPERATOR’S MANUAL MUST BE READ AND UNDERSTOOD
PRIOR TO OPERATING YOUR MEC SELF-PROPELLED SCISSORS.
THE USER/OPERATOR SHOULD NOT ACCEPT OPERATING
RESPONSIBILITY UNTIL HE/SHE HAS READ AND UNDERSTANDS
THE OPERATOR’S MANUAL AS WELL AS HAVING OPERATED THE
MEC SCISSOR LIFT UNDER SUPERVISION OF AN AUTHORIZED,
TRAINED AND QUALIFIED OPERATOR.
IT IS ESSENTIAL THAT THE OPERATOR OF THE AERIAL WORK
PLATFORM IS NOT ALONE ON THE WORKPLACE DURING
OPERATION.
MODIFICATIONS OF THIS MACHINE FROM THE ORIGINAL DESIGN
AND SPECIFICATIONS WITHOUT WRITTEN
PERMISSION FROM MEC ARE STRICTLY FORBIDDEN. A MODIFICA-
TION MAY COMPROMISE THE SAFETY OF THE MACHINE, SUB-
JECTING OPERATOR(S) TO SERIOUS
INJURY OR DEATH.
Your MEC Scissor Lift has been designed, built, and tested to provide safe, dependable service.
Only authorized, trained and qualified personnel should be allowed to operate or service the
machine.
MEC, As Manufacturer, Has No Direct Control Over Machine Application And Operation.
Proper Safety Practices Are The Responsibility Of The User And All Operating Personnel.
If There Is A Question On Application And/Or Operation Contact:
Page iv
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
MACHINE SPECIFICATIONS
Meets Requirements of ANSI A92.6-2006 Section 4
*Metric equivalent of working height adds 2m to platform height. U.S. adds 6 ft. to platform height.
**Weight may increase with certain options or country standards.
Working Height*
Platform Height
Stowed Height
Rails Folded Down
Rails Up
Maximum Number of Occupants
Lift Capacity (Evenly Distributed)
Rollout Deck Capacity
Platform Dimensions
With Roll-Out Deck extended
With Roll-Out Deck Retracted
Guard Rail Height
To e B o ard Height
Rollout Deck Length
Overall Length
Overall Width
Wheel Base
Wheel Track
Turning Radius
Inside
Outside
Ground Clearance
Machine Weight** (Unloaded) (Approx.)
Drive System (Proportional)
Drive Speed (Platform Elevated - Forward)
Drive Speed (Platform Lowered)
Lift/Lower Speed (Approx.)
Gradeability
Ground Pressure/Wheel (Maximum)
Wind Speed (Maximu
m)
Tire Size-Standard (Solid, non-marking rubber)
Wheel Lug Nut Torque
Hydraulic Pressure
Main System
Lift System
Steer
Hydraulic Fluid Capacity
Power System – Voltage
Battery Charger
Input
Output
Batteries Four 6 Volt deep-cycle
Electric Motor
1532ES 1932ES 2033ES 2633ES
21 ft 6.57 m
15 ft 4.57 m
75 in 1.90 m
NA
2
600 lbs 272.2 kg
250 Ibs 113.4 kg
102 in 2.59 m
66 in 1.68 m
40.5 in 1.03 m
7 5/8 in 0.19 m
36 in 0.91 m
74 in 1.88 m
31.5 in 0.96 m
50 in 1.27 m
27.37 in 0.70 m
2 in 0.05 m
67 in 1.7 m
3 in 0.76 m
2725 lbs 1236 kg
17 sec / 20 sec
25% / 14°
105 psi 7.4kg/cm²
0 m/s
14 in dia. x 4.5 in 35.56 cm x 11.43 cm
75 - 85 ft lbs 102 - 115 Nm
2750 psi 190 bar
1900 psi 131 bar
850 psi 62 bar
3 gal 11.36 liters
24 Volts DC
25 ft 7.79 m
19 ft 5.79 m
79 in 2 m
NA
2
500 lbs 226.8 kg
250 lbs 113.4 kg
102 in 2.59 m
66 in 1.68 m
40.5 in 1.03 m
7 5/8 in 0.19 m
36 in 0.91 m
74 in 1.88 m
31.5 in 0.96 m
50 in 1.27 m
27.37 in 0.70 m
2 in 0.05 m
67 in 1.7 m
3 in 0.76 m
3060 lbs 1388 kg
0 - 0.5 mph 0 - 0.8 km/h
0 - 2.5 mph 0 - 4.02 km/h
17 sec / 20 sec
25% / 14°
113 psi
7.9 kg/cm²
0 m/s
2750 psi 190 bar
2600 psi 180 bar
850 psi 62 bar
3 gal 11.36 liters
100-220 Volt AC, 50/60 Hz, 5.6 Amp
24 Volt DC, 25 Amps Tapering,
Timed Shutoff
220 Amp hours @ 20 hour rating
2.0 h.p. (1.49 kW): 3000 r.p.m.
24 Volts DC
26 ft 7.92 m
20 ft 6.10 m
86.25 in 2.19 m
76.5 in 1.94 m
2
800 lbs 363 kg
250 lbs 113 kg
133 in 3.38 m
91 in 2.31 m
43.5 in 1.10 m
6 in 15.2 cm
46.5 in 1.18 m
100.25 in 2.54 m
33 in 0.84 m
71 in 1.8 m
27.37 in 0.70 m
0 in 0 cm
88 in 2.24 m
3.5 in 8.9 cm
3815 lbs 1731 kg
18 sec / 35 sec
28% / 15.5°
129 psi 9.0 kg/cm²
0 m/s
2750 psi 190 bar
2400 psi 166 bar
900 psi 62 bar
3 gal 11.36 liters
24 Volts DC
32 ft 9.75 m
26 ft 7.92 m
86.25 in 2.19 m
76.5 in 1.94 m
2
500 lbs 227 kg
250 lbs 113 kg
133 in 3.38 m
91 in 2.31 m
43.5 in 1.10 m
6 in 15.2 cm
46.5 in 1.18 m
100.25 in 2.54 m
33 in 0.84 m
71 in 1.8 m
27.37 in 0.70 m
0 in
0 cm
88 in 2.24 m
3.5 in 8.9 cm
4650 lbs 2109 kg
0 - 0.6 mph 0 - 1.0 km/h
0 - 3.0 mph 0 - 4.80 km/h
18 sec / 35 sec
28% / 15.5°
129 psi 9.0 kg/cm²
0 m/s
16 in dia. x 5 in 40.6 x 12.7 cm
75 - 85 ft lbs 102 - 115 Nm
2750 psi 190 bar
2600 psi 180 bar
900 psi 62 bar
3 gal 11.36 liters
24 Volts DC
100-220 Volt AC, 50/60 Hz, 5.6 Amp
24 Volt DC, 25 Amps Tapering,
Timed Shutoff
220 Amp hours @ 20 hour rating
2.0 h.p. (1.49 kW): 3000 r.p.m.
Page v
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
MACHINE SPECIFICATIONS
Meets Requirements of ANSI A92.6-2006 Section 4
*Metric equivalent of working height adds 2m to platform height. U.S. adds 6 ft. to platform height.
**Weight may increase with certain options or country standards.
Working Height*
Platform Height
Stowed Height
Rails Folded Down
Rails Up
Maximum Number of Occupants
Lift Capacity (Evenly Distributed)
Rollout Deck Capacity
Platform Dimension
s
With Roll-Out Deck extended
With Roll-Out Deck Retracted
Guard Rail Height
To e B o ard Height
Rollout Deck Length
Overall Length
Overall Width
Wheel Base
Wheel Track
Turning Radius
Inside
Outside
Ground Clearance
Machine Weight** (Unloaded) (Approx.)
Drive System (Proportional)
Drive Speed (Platform Elevated - Forward)
Drive Speed (Platform Lowered)
Lift/Lower Speed (Approx.)
Gradeability
Ground Pressure/Wheel (Maximum)
Wind Speed (Maxim
um)
Tire Size-Standard (Solid, non-marking rubber)
Wheel Lug Nut Torque
Hydraulic Pressure
Main System
Lift System
Steer
Hydraulic Fluid Capacity
Power System – Voltage
Battery Charger
Input
Output
Batteries Four 6 Volt deep-cycle
Electric Motor
0 m/s wind
12.5 m/s wind
2047ES 2647ES3247ES
26 ft. 8.10 m
20 ft. 6.10 m
82.6 in. 2.10 m
63.8 in. 1.62 m
3
1
1,250 lbs. 567 kg
250 lbs. 113 kg
133.5 in. 3.39 m
91 in. 2.31 m
43.4 in. 1.10 m
6 in. 15.2 cm
42.1 in. 1.07 m
99.in. 2.51 m
47 in. 1.19 m
71 in. 1.80 m
41 in. 1.04 m
0 in. 0 cm
94 in. 2.4 m
3.5 in. 8.9 cm
4,450 lbs. 2018 kg
28/35 sec.
25% / 14°
180 psi 12.7kg/cm²
0 m/s
16 in D x 5 in. W 40.6cm D x 12.7cm W
75 - 85 ft lbs 102 - 115 Nm
2750 psi 190 bar
2500 psi 172 bar
1100 psi 76 bar
4.5 gal 17.0 liters
24 Volts DC
32 ft. 9.92 m
26 ft. 7.92 m
88.8 in. 2.26 m
70.0 in. 1.78 m
3
N/A
1,000 lbs. 454 kg
250 lbs. 113 kg
133.5 in. 3.39 m
91 in. 2.31 m
43.4 in. 1.10 m
6 in. 15.2 cm
42.1 in. 1.07 m
99.in. 2.51 m
47 in. 1.19 m
71 in. 1.80 m
41 in. 1.04 m
0 in. 0 cm
94 in. 2.4 m
3.5 in. 8.9 cm
5,300 lbs. 2404 kg
0 - 0.62 mph 0 - 1.0 km/h
0 - 2.5 mph
0 - 4.0km/h
30/35 sec.
25% / 14°
194 psi 13.6kg/cm²
0 m/s
3000 psi 207 bar
2500 psi 172 bar
1100 psi 76 bar
4.5 gal 17.0 liters
100-220 Volt AC, 50/60 Hz, 5.6 Amp
24 Volt DC, 25 Amps Tapering,
Timed Shutoff
220 Amp hours @ 20 hour rating
2.0 h.p. (1.49 kW): 3000 r.p.m.
24 Volts DC
38 ft. 11.75 m
32 ft. 9.75 m
95.1 in. 2.42 m
76.3 in. 1.94 m
2
700 lbs. 317 kg
250 lbs. 113 kg
133.5 in. 3.39 m
91 in. 2.31 m
43.5 in. 1.10 m
6 in. 15.2 c m
42.1 in. 1.07 m
99.in. 2.51 m
47 in. 1.19 m
71 in. 1.8 m
41 in. 1.04 m
0 in. 0 cm
94 in. 2.4 m
3.5 in. 8.9 cm
5,990 lbs. 2717 kg
42/45 sec.
25% 14°
205 psi 14.4kg/cm²
0 m/s
3000 psi 207 bar
2045 psi 141 bar
1100 psi 76 bar
4.5 gal 17.0 liters
24 Volts DC
N/A
Page vi
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
THIS PAGE INTENTIONALLY LEFT BLANK.
Page 1-1
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
SECTION 1:
SAFETY
Page 1-2
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SAFETY RULES AND PRECAUTIONS
MEC designs self-propelled scissor lifts to be safe and reliable. They are intended to posi-
tion personnel, along with their necessary tools and materials to overhead work locations.
The owner/user/operator of the machine should not accept responsibility for the operation
of the machine, unless properly trained.
ANSI A92.6 and other applicable standards identify requirements of all parties who may
be involved with self-propelled elevating work platforms. The A92.6 Manual of Responsibili-
ties is considered a part of this machine and can be found in the manual compartment,
located at the platform control station.
To insure safe use of machine, inspections specified in Section 6.7 of ANSI A92.6-2006 must
be performed at designated intervals as prescribed by ANSI A92.6-2006.
ELECTROCUTION HAZARD!!! THIS MACHINE IS NOT INSULATED!!
Maintain safe clearance from electrically charged conductors (power lines) and apparatus.
You must allow for machine sway (side to side movement) when elevated and electrical
line movement. This machine does not provide protection from contact with, or proximity
to, an electrically charged conductor.
You must maintain a CLEARANCE OF AT LEAST 10 FEET (3.05 m) between any part of
the machine, or its load, and any electrical line or apparatus carrying over 300 volts up to
50,000 volts. One foot (30.5 cm) additional clearance is required for every additional
30,000 volts.
DEATH OR SERIOUS INJURY will result from contact with or inadequate clearance from
any electrically charged conductor.
Observe
Minimum Safe Approach Distance
as illustrated on next page.
Page 1-3
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
M.S.A.D. = MINIMUM SAFE APPROACH DISTANCE
MINIMUM SAFE APPROACH DISTANCE (M.S.A.D.)
to energized (exposed or insulated) power lines and parts.
DENOTES PROHIBITED ZONE
DANGER:
CAUTION:
DO NOT ALLOW MACHINE, PERSONNEL OR CONDUCTIVE MATERIALS
INSIDE PROHIBITED ZONE.
MAINTAIN M.S.A.D. FROM ALL ENERGIZED LINES AND PARTS AS WELL
AS THOSE SHOWN.
ASSUME ALL ELECTRICAL PARTS AND WIRES ARE ENERGIZED
UNLESS KNOWN OTHERWISE.
DIAGRAMS SHOWN ARE ONLY FOR PURPOSES OF ILLUSTRATING
M.S.A.D. WORK POSITIONS, NOT ALL WORK POSITIONS.
VOLTAGE RANGE MINIMUM SAFE APPROACH DISTANCE
(Phase to Phase)
0 to 300V
Over 300V to 50KV
Over 50KV to 200KV
Over 200KV to 350KV
Over 350KV to 500KV
Over 500KV to 750KV
Over 750KV to 1000KV
AVOID CONTACT
10
15
20
25
35
45
3.05
(Feet) (Meters)
4.60
6.10
7.62
10.67
13.72
Page 1-4
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SAFETY SYMBOLS
This section of the manual contains important information of the safe use of your MEC Scissors.
Failure to read, understand, and follow all safety rules, warnings, and instructions will unneces-
sarily expose you and others to dangerous situations. For your safety and the safety of those
around you, you must operate your machine as instructed in this manual.
You, the operator, are the single most important factor for safety when using any piece of equip-
ment. Learn to operate your machine in a safe manner.
To help you recognize important safety information, we have identified warnings and instructions
that directly impact on safety with the following signals:
“DANGER” INDICATES AN IMMINENTLY HAZARDOUS SITUATION
WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS
INJURY. THIS SIGNAL WORD IS LIMITED TO THE MOST EXTREME
SITUATIONS.
“WARNING” INDICATES A POTENTIALLY HAZARDOUS SITUATION
WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS
INJURY.
CAUTIONindicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also be used to
alert against unsafe practices. “CAUTION” is used for property-damage
only accidents.
Page 1-5
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
Only authorized, trained and qualified personnel should operate the scissor lift.
NEVER fasten fall protection lanyard to an adjacent structure while on the platform.
Make sure that the platform entry is properly closed and secure before operating machine
from the platform.
NEVER exceed platform rated capacity. Review the section titled “Machine Specifications”
(earlier in this manual) regarding model capacities and dimensions.
Before operating the machine, read and understand all safety and control information
found on the machine and in this manual.
When operating the machine follow all safety and control information found on the ma-
chine and in this manual.
Evenly distribute loads placed on the platform.
NEVER use scaffolding, ladders or similar items to extend your reach while on the plat-
form.
NEVER climb down the beam assembly while the platform is raised.
The “Moving the Machine” section (described later in this manual) requires that the brake
be released. After performing this procedure, there is no means to stop the machine’s
travel. MEC recommends using this procedure only in cases of emergency, and only for a
short distance. Be on guard against machine runaway on sloping surfaces. Movement
speed shall not exceed 5 MPH (8.0 kph).
NEVER attempt to open any hydraulic line or component without first relieving all system
pressure.
NEVER alter, modify, or disable any safety devices or interlocks.
NEVER recharge the battery near sparks or open flames. Lead-acid batteries generate
EXPLOSIVE HYDROGEN GAS. Always wear safety glasses.
NEVER use the machine outdoors during electrical storms or in high wind situations.
Only raise the platform when the machine is on a firm, level surface.
SECURE all tools and other loose items to prevent injury to persons working on or below
the platform.
Precautions should be taken to prevent unauthorized personnel from operating the plat-
form with the ground controls while the platform is in use.
Page 1-6
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
Unassisted loading or unloading of scissorlift from a truck or trailer is not recommended.
Before disengaging brakes or disconnecting from a tow vehicle, ensure that the machine
cannot roll.
Complete the “Operational Checklist” at designated intervals.
Use of scissor lift as a crane to lift oversized or hanging loads is prohibited.
Always check route and areas are clear before driving, lifting or lowering.
It is recommended to avoid sudden braking or steering. Go slowly and leave more maneu-
vering room during cold weather operation.
FALL PROTECTION NOTICE
The Guardrail System around the perimeter of the platform is the fall protection system for
self-propelled elevating work platforms. It is prohibited to use an Aerial Work Platform manufac-
tured by MEC with any portion, or all, of the guardrails removed.
Lanyard anchorage points on this type of equipment are not required to conform to the applicable
ANSI/SIA Standard.
THE IMPROPER USE OF FALL ARREST SYSTEMS MAY CAUSE
MACHINE TO TIP RESULTING IN SERIOUS INJURY OR DEATH.
However, if anchorage points for lanyard attachments are required by site authorities or other
regulations, the anchorage points on all equipment manufactured by MEC are recommended to
be used for work positioning restraints of personnel only. Lanyard lengths are to be determined
by operator/owner to restrict the operator to the confines within the Guardrail System.
Page 1-7
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
SAFETY AND CONTROL DECAL LOCATIONS - CONTROLS
90729
90735
7156 8391
90723
90741
9052
90732
90263
90750
90751
90348
90401
8779
(2033ES)
9933
(2047ES)
(2633ES)
90268
90401
(1532ES)
(1932ES)
9932
(2047ES)
9947
(2047ES)
Page 1-8
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SAFETY AND CONTROL DECAL LOCATIONS - 32 SERIES
9910
90739
9138
8816
8402
90719
8402
9910
8503
90717
7982
90736
9137
90722 90721
90730
90733
8806
8805
(1532ES)
(1932ES)
(3X)
(Both Sides)
(Both Sides)
(Both Sides)
(Both Sides)
OPTION
(4X)
90718
INSIDE MANUAL CASE
Page 1-9
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
SAFETY AND CONTROL DECAL LOCATIONS - 32 SERIES
6873
90725
90826
91083
90748
90726
90267
91553
Page 1-10
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SAFETY AND CONTROL DECAL LOCATIONS - 33 SERIES
9910
90739
8765
90716
8402
90719
8402
9910
8503
90717
7982
9073690829
90722
90721
90730
90733
90718
8806
8805
(2033ES) (2633ES)
(3X)
(Both Sides)
(Both Sides)
(Both Sides)
(Both Sides)
OPTION
INSIDE MANUAL CASE
(6X)
Page 1-11
1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification April 2007
SAFETY AND CONTROL DECAL LOCATIONS - 33 SERIES
(2633ES)
(2033ES)
6873
90725
90826
91083
6556
91553
90726
90267
Page 1-12
April 2007 1532ES - 1932ES / 2033ES - 2633ES / 2047ES - 2647ES - 3247ES Operator’s Manual: ANSI Specification
SAFETY AND CONTROL DECAL LOCATIONS - 47 SERIES
9910
90739
9624
9625
8402
90719
8402
9910
8503
90717
7982
90911
90910
90722
90721
90730
90733
90718
8806
8805
(2047ES)
(2647ES)
90912
(3247ES)
(3X)
(Both Sides)
9623
(Both Sides)
(Both Sides)
8402
(Both Sides)
(Both Sides)
(Both Sides)
OPTION
INSIDE MANUAL CASE
(6X)
700 LBS
317 kg
2-PERSONS 1-PERSON
1-PERSON
450 LBS
204 kg
250 LBS
113 kg
120 LBS
533 kg
90910
1000 LBS
454 kg
3-PERSONS 2-PERSONS
1-PERSON
750 LBS
341 kg
250 LBS
113 kg
150 LBS
667 kg
90911
1250 LBS
567 kg
3-PERSONS 2-PERSONS
1-PERSON
1000 LBS
454 kg
250 LBS
113 kg
188 LBS
834 kg
90912
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Mec 3247ES Operating instructions

Category
Floor Machine
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI