Veise 801 User manual

Type
User manual
Thank you for purchasing our products. Please review this manual thoroughly before operating your device.
All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
Latch(A)
Strike(C)
Rear Lever
(E)
Front Lever
(F)
Latch & Strike
screws (B)
Mounting Screw
(D)
TOOL REQUIRED: Do not use an electric
screwdriver during installation.
Parts list
Latch x1
ALatch & Strike screws x4
BStrike x1
C
Mounting
Screw x2
DHand Tool x1
HRear Lever x1
EFront Lever x1
F
1. Prepare the door
and check dimensions
If your door already has the holes shown in the picture
below, proceed to the next step, if your door does not
have holes, use the mounting template to drill a new hole.
2-1/8"
(54mm) 1"
(25mm)
2-3/8" or 2-3/4"
(60 or 70mm)
Door thickness:
1-3/8" to 2"
(35mm or 50mm)
1"
25mm
2. Latch backset adjustment
Backset is the distance from the door edge to the center of the hole in the door.
The latch is provided with adjustable design which can fit either 2-3/8’’(60mm) or 2-3/4’’(70mm)
backset.
2-3/8"
(60mm)
2-3/4"
(70mm)
A. If the backset of your
door is 2-3/8"(60mm), no
need to adjust the latch.
B. If the backset of your door is 2-3/4"(70mm), please adjust the latch.
3. Install latch and strike
The latch should be aligned with the
chiseled properly.
IMPORTANT:
Make sure the hole in door frame is drilled a minimum of
1" (25mm) deep.
IMPORTANT:
4. Reverse lever direction (Optional)
1. Find the joint point, press the point by using
the Hand Tool.
2. Till the joint point is pressed down completely,
then pull out the lever. Sometimes, it may
happen that the joint point is unable to be
pressed down completely, in this case, please
press the joint point along with pulling out the
lever.
Pull out
The front lever is installed for right-handed door in
default. If your door is left-handed, please
exchange the front and rear lever with each other.
While you exchange the lever direction, the edge of
inner mechanism may be a little sharp, please protect
your hands from being hurt.
IMPORTANT: WARM REMINDER:
ARear Lever disassembly steps
1
2
Joint point
3
Pull out
1
2
CExchange the lever
Exchange the lever of front and rear with each other,
press the lever back till you hear a mild “Ding” sound.
1. Rotate the lever and find the joint point of the lever
through the hole on the housing.
2. Press the joint point with the Hand Tool, till the joint
point is pressed down completely, then pull out the
lever.
Sometimes, it may happen that the joint point is
unable to be pressed down completely, in this case,
please press the joint point along with pulling out
the lever.
BFront Lever disassembly steps
Align the hole with the
inside joint point
5. Install front and rear lever
The base of spindle must be
rotated aligning to the hole.
6. Test the Lever
Keep the door open,
checking out front and rear
lever to test if it works
smoothly.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Veise 801 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI