Endura Frame and Jamb Machining Operating instructions

Brand: Endura

Model: Frame and Jamb Machining

Type: Operating instructions

PanoLock™ - Frame Machining - Strike Plate Assembly

PanoLock+™ Multi-Point Lock Instructions

Frame Machining - Strike Plate

8817 West Market Street

Colfax, NC 27235 | 800.334.2006

www.enduraproducts.com

Required tooling includes:

STEP 1

STEP 2

WARNING – Make sure router is unplugged when adjusting bit depth.

WARNING – Use proper personal protective equipment when operating a router.

A ½" OD x 2" Router Bit A 5/8" OD Router Guide Collar

First pocket machining. Set the router bit depth to 25/32" using the guide on the back of the template BASE.

Machining details are found in Endura print # 16031-300.

Install the 5/8" OD Router Guide Collar

on your router. It will be used for all

steps in the jamb fabrication.

2U-INSTR-JAMB

Last Updated: 11/17/2023

PanoLock™ - Frame Machining - Strike Plate Assembly

STEP 3

Determine location of middle strike plate.

See last page of instruction for spacing between centerlines of each strike plate.

1. Measure from top of door panel to latch bore.

This is measurement “X”.

2. If using a standard 3/4" head jamb, take

measurement “X” and subtract 2-5/8”. This is

measurement “Y”.

3. From the top of the jamb, measure down “Y” to

locate the center of the middle strike plate.

PanoLock™ - Frame Machining - Strike Plate Assembly

STEP 5

Turn router on. Rotate bit into center of template pocket to prevent damaging edge of template. Remove all material

within template pocket. Remove all dust and debris from frame.

Locate the template base on the frame as shown.

Align the center of the template with the centerline

location of the strike plate assembly. Attach the

template to the frame with screws, at two locations

shown.

STEP 4

Centerline of

middle strike

plate - from

Step 3.

Second pocket machining.

Reset the router bit depth

to 1-1/16" using the guide

on the back of template

INSERT A.

STEP 6

PanoLock™ - Frame Machining - Strike Plate Assembly

STEP 7

Place INSERT A into template BASE as shown.

STEP 8

Turn router on. Rotate bit into center of template pocket to prevent damaging edge of template. Remove all material

within template pocket. Remove all dust and debris from frame.

Third pocket machining. Reset the router bit depth to

1-1/2" using the guide on the front of template INSERT B.

STEP 9

Place INSERT B into template base as shown.

STEP 10

PanoLock™ - Frame Machining - Strike Plate Assembly

STEP 11

Turn router on. Rotate bit into center of template

pocket to prevent damaging edge of template.

Remove all material within template pocket.

Remove all dust and debris from frame. Strike plate

assembly frame mortise is now complete. Repeat

steps for remaining pockets.

STEP 12

An alternative to moving the routing template for each pocket

is to attach template BASES, spaced apart to align with all

lock latching points. Using threaded rods and nuts, template

BASES can be joined together, and spaced as needed.

PanoLock™ - Frame Machining - Strike Plate Assembly

28.000 (6/8 LOCK)

44.000 (8/0 LOCK)

23.125

5.500

3.500

TOP

BOTTOM

LATCH CROSS BORE

DEADBOLT

CROSS BORE

.158

.437

3X SECTION A-A

SCALE 1 : 1

4.016

2.375

1.947

R.317 X2

.434

1.223

R.250 X4

.170

3X DETAIL B

SCALE 1 : 3

REV

DATE

REVISION DESCRIPTION

11/16/20

INITIAL RELEASE

11/17/20

ADDED 8/0 DIMENSIONS

01/18/23

SECOND STEP ROUTE CHANGED

RELEASED

ASSEMBLY

DATE: 4/5/2011

Adam Kendall

PANOLOCK

STRIKE ROUTE

REV

TITLE

DATE

CHECKED BY

MODELED BY

RAW PART NUMBER

DRAWING NUMBER

12/02/19

01/18/23

SHEET 1 OF 1

1:6

16031-300

The information contained in this document is the confidential

and proprietary information and trade secrets of Endura

Products, Inc. Any disclosure, use, or dissemination of such

information without the express written permission of Endura

Products, Inc. is strictly prohibited. Endura Products, Inc.

also owns any and all Intellectual property rights embodied in

such information, including patent rights, copyrights, and

trademark rights, and no license of any intellectual property

rights is intended, nor shall any license be implied, as a result

of the receipt of this document.

DATE

SIZE

SCALE

8817 W. MARKET ST. COLFAX, NC 27235

PHONE:(336) 668-2472 FAX:(336) 668-4478

WWW.ENDURAPRODUCTS.COM

INSPECTION DIMENSIONS

ARE CIRCLED

Maximum lead (Pb) content of all parts and/or

coatings to be 200ppm (0.02% by weight).

Endura Frame and Jamb Machining Operating instructions

Endura Frame and Jamb Machining Operating instructions

Endura Frame and Jamb Machining Operating instructions

Related papers

Other documents