Page is loading ...
Wireless product temperature sensor with battery
W-LINKpro-B_Vx.x_PI_2019-08_EN 1
Subject to technical changes
W-LINKpro-B
1 W-LINKpro-B
Wireless product temperature sensor with battery
1.1 Front view
1.2 Features
• W-LINKpro-B product temperature sensor for installation in refrigeration units
• Wireless transmission of temperatures
• Battery operated
• 2 control keys and 1 LED (green/red) for status display
• Easy installation with cable straps, adhesive pad or installation plate
• Similar product properties
1.3 Device variants:
• W-LINKpro-B with internal temperature sensor
• W-LINKpro-BE with 1m cable sensor
• W-LINKpro-BE01 with 0.1m cable sensor
• W-LINKpro-BE3 with 3m cable sensor
Fig. 1: With internal temperature sensor Fig. 2: With external temperature sensor
Wireless product temperature sensor with battery
2 W-LINKpro-B_Vx.x_PI_2019-08_EN
Subject to technical changes
W-LINKpro-B
1.4 Safety instructions
Writing conventions
WARNING • Avoid the described hazard: otherwise there is danger from electric voltage which could cause
death or serious physical injury.
For your safety
For safe operation and to avoid personal injury and equipment damage through operator error, always
read these instructions, become familiar with the device, and follow all safety instructions on the prod-
uct and in this document, as well as the safety guidelines of Wurm GmbH & Co. KG Elektronische
Systeme. Keep these instructions ready to hand for quick reference and pass them on with the device
if the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in case of improper use or use for
other than the intended purpose.
WARNING DANGER TO LIFE FROM ELECTRIC SHOCK AND/OR FIRE!
• Do not open the device.
• Do not repair the device yourself. If the device requires repairs, send it in with an exact descrip-
tion of the fault.
Validity of the documentation
This document automatically ceases to be valid if a new technical description is issued.
Manufacturer: Wurm GmbH & Co. KG Elektronische Systeme, Morsbachtalstraße 30, D-42857 Remscheid
You can find more information on our website at www.wurm.de
Target group These instructions are intended for "service technicians".
Intended use W-LINKpro-B is a product temperature sensor for installation in refriger-
ation units.
Wurm Infocenter paperless info
Date
2019-08 Documentation status
Wireless product temperature sensor with battery
W-LINKpro-B_Vx.x_PI_2019-08_EN 3
Subject to technical changes
W-LINKpro-B
1.5 Installation
1.6 Display and control elements
Press the keys using a thin pointed object, e.g. screwdriver or pen.
Activate the W-LINKpro-B and log into the system
• Press the key I (1).
The green LED (2) is lit briefly.
Deactivate W-LINKpro-B an log out of the system
• Press the key O (3).
The red LED (2) is lit briefly.
Cable strap installation
Various openings are provided in the back of the housing
for installation with cable straps. We recommend always
using 2 cable straps for installation.
For installation instructions, please see the cable strap
packaging.
Adhesive pad installation
An adhesive pad is available for installation on flat sur-
faces. The surface to which the pad is to be attached
must be free of grease and dust, and warmer than 10°C.
• Remove the protective foil from the adhesive pad.
• Position the adhesive pad in the recess provided in
the rear of the housing.
• Press the adhesive pad firmly onto the housing.
• Remove the second protective foil.
• Press the housing firmly onto its installation position.
W-LINKpro-M1 installation plate
Mounting plate for W-LINKpro Series sensors
(Dimensions: (WxHxD) 38 x 63 x 5mm)
1Key I
2LED green/red
3Key O
1
2
3
Wireless product temperature sensor with battery
4 W-LINKpro-B_Vx.x_PI_2019-08_EN
Subject to technical changes
W-LINKpro-B
1.7 Technical data
NOTICE • To calibrate the measured section, please refer to the instructions in the documentation for the
device.
Power supply Battery, service life >10 years
Display 1 x green/red LED
Dimensions (WxHxD) 47 x 69 x 28mm
Fastening Cable straps, adhesive pads or installation plate
Ambient temperature Operation: -25...+55°C, storage: -25...+70°C
Degree of protection IP64
Weight About 55g
CE conformity - 2014/53/EU (Radio Equipment Directive)
RoHS II
/
