Unbranded SXB056844 User manual

GENERAL GUIDELINES

WARNINGS

Please read the following instruction carefully and use the product accordingly.

During assembly, keep parts and packaging materials away from children and pets as there

could cause injury and are a potential choking hazard.

Avoid sharp objects or corrosive chemicals to prevent damage to the product.

Please open the item slowly and cautiously to avoid pinching your hands by metal joints,

especially children.

If an odor is present when first opening the package, please leave the unwrapped product in

a shaded and ventilated area for a few days to air out.

Please follow the assembly instructions precisely and only use the product as intended.

Prior to assembly, please check the product for defects or missing accessories. If any

defects are found or accessories are missing, do not use product as damage or injury

may occur;

Please contact us for assistance and replacement.

It is suggested you regularly check the products bolts and connections to ensure safe use.

Assemble the item on a soft flat and clean surface to avoid scratches and damage.

It is recommended that two people assemble this product.

Please keep this manual and hand it over when you transfer the product.

This summary may not include every detail of all variations and considered steps. Please

contact us when further information and help are needed.

IMPORTANT INFORMATION

READ CAREFULLY.

KEEP THIS INFORMATION FOR FURTHER REFERENCE.

NOTES

Serious or fatal crushing injuries can occur from furniture tip-over. To prevent this furniture

from tipping over it must be permanently fixed to the wall.

Since different wall materials require different types of fixing device, for advice on suitable

fixing systems, contact your local specialized dealer.

ANTI-TIP WARNING

If you have any further questions, please feel free to contact us

by email or official website: [email protected]

We will reply ASAP.

Enjoy your new purchase!

Before installation, please make sure you have all the hardware,

the serial numbers are properly labeled corresponging to the list,

and the quantity is correct.

5/16

(8 mm)

1/8

(3 mm)

1

EXPLODED DRAWING

1

2

3

4

5

6

7

8

9

10

11 12

8

9

10

11 12

13

1 2

2

1

2

PARTS

13

7

Part

7

board is assembled on the upper drawer ;

Part

13

board is assembled on the bottom drawer ;

1

2

REMARK

X28

B

X28

C

X1

X8

J

X28

A

X14

G

H

X19

F

X4

X2

D

K

X2

I

X1

X8

N

O

X4

E

E2

E1

X4

M

X4

L

M4x14 M4x11

M6x28

M4x30

+

=

D1 D2

X3

Q

X1

PX1

R

3

PRESS

PULL

Press the plastic part in the indicated direction to

separate drawer runner and before assembling.

Please grip the part while sliding the part.

1.

2.

E1 E2

E2

E1

REMARK

MINIFIX POSITION

4

1

2

X2

I

X6G

M4x11

X4

B

M4x14

FGM4x11

DEV

V

ISE

214/

REMARK

Put a blanket under the board to avoid scratch or damage.

I

G×6

B×4

7

13

5

3

X4

G

X2

E2

M4x11

G

FRONT

FRONTFRONT

E2

FRONT

1

93

M4x14

FGM4x11

Long

Short

Long

Short

7

13

6

4

5

E2

X4

B

G

×2

M4x14

FGM4x11

FRONT

X4

G

X2

E2

M4x11

Long

Short

12

7

6

7

X8

A

X4

B

J

X3F

M4x14

X1

J

REMARK

Please do not screw too deep or too shallow.

A

B4

A×8

F×3

2

3

8

When installing, please make

sure the screws are flattened, not

crooked; Otherwise the drawers

will not be installed perfectly.

REMARK

10

2. Then please install part from the front of part .

F

1. Please locate the holes from the back of part .

E1 Back

E1 Front

E1

18

FRONT

F

X8F

F

FF

F

M4x14

X4

E1

TOP

BOTTOM

FRONT

23

9

BALL BEARING

1. Please full extend the

slide

runners.

2. Simply push the ball bearing cart all the way to the end of the slide(in both sides).

FRONT FRONT

REMARK

TOP

BOTTOM

FRONT

23

10

2. Align the slide runners on the drawer with the unit and push it carefully inside until it stops.

REMARK

1. Note the difference between the part 7 and the part 13 .

3. If the drawer does not go in smoothly please take it out and repeat the step.

10

FRONT FRONT

TOP

BOTTOM

FRONT

7

12

13

23

11

X16

B

11

12

B16

4

5

12

X8

C

13

C×4

2

3

4

5

C4

2

3

13

X12

A

X4

C

14

15

A12

1

3

6

C4

2

6

M6x28

X3

Q

X1

P

X1

R

Q

PQQ

14

X8

C

16

1

3

C8

2

1

15

X8

A

17

18

×2

X2

D

D1

D1 D1

D2

X8

F

M4x14

9

A4

8

F4

16

19

12

X4H

M4x30

10

13

Let the grooves on part 10 be connected

to the groove on part 12 and13 .

REMARK

×4

H

17

X4

C

20

8

11

C4

18

X2

K

21

22

X4

N

X2L

X2

M

2

×4

N

M

K

ML

L

Page is loading ...

Unbranded SXB056844 User manual

Unbranded SXB056844 User manual

Related papers

Other documents