Unbranded SXB056846 User manual

GENERAL GUIDELINES

WARNINGS

Please read the following instruction carefully and use the product accordingly.

During assembly, keep parts and packaging materials away from children and pets as there

could cause injury and are a potential choking hazard.

Avoid sharp objects or corrosive chemicals to prevent damage to the product.

Please open the item slowly and cautiously to avoid pinching your hands by metal joints,

especially children.

If an odor is present when first opening the package, please leave the unwrapped product in

a shaded and ventilated area for a few days to air out.

Please follow the assembly instructions precisely and only use the product as intended.

Prior to assembly, please check the product for defects or missing accessories. If any

defects are found or accessories are missing, do not use product as damage or injury

may occur;

Please contact us for assistance and replacement.

It is suggested you regularly check the products bolts and connections to ensure safe use.

Assemble the item on a soft flat and clean surface to avoid scratches and damage.

It is recommended that two people assemble this product.

Please keep this manual and hand it over when you transfer the product.

This summary may not include every detail of all variations and considered steps.

Please contact us when further information and help are needed.

IMPORTANT INFORMATION

READ CAREFULLY.

KEEP THIS INFORMATION FOR FURTHER REFERENCE.

NOTES

If you have any further questions, please feel free to contact us

by email or official website: : [email protected]

We will reply ASAP.

Enjoy your new purchase!

Before installation, please make sure you have all the hardware,

the serial numbers are properly labeled corresponging to the list,

and the quantity is correct.

1

EXPLODED DRAWING

PARTS

X24 X24

B

X24

C

A

X4 X49

E

X4

F

D

X16 X1

H

GX4

I

X5

JX1

K

12 2 1

3

5

7

6

4

898

8

4

M4x11

2

1

5

6

MINIFIX POSITION

REMARK

2. Please do not screw too deep or too shallow.

A

1. Put a blanket under the board to avoid scratch or damage.

X16A

A×16

3

2

3

X8

B

X4A

A

F

A

214/

×2

X4

F

X8

E

1

4

B×4

E×4

M4x11

4

A

X16

B

X4A

4

5

×2

X16

E

2

3

E8

B8

1

4

If screws do not align with the holes, loosen the screw pointed in the

picture slightly, adjust the length of the hinge until it is aligned, and

then retighten the screw on the hinge.

REMARK

M4x11

5

6

7

X4

C

X4

C

3

C×4

2

1

3

21

4

3

2

1

4

C4

6

8

9

Long Short

79mm 64mm

X8

C

X8

C

33

5

FRONT

6

Long Short

79mm 64mm

FRONT

5

6

2

4

6

C8

7

REMARK

1. The part 9 is shorter than part 8 .

10

11 X5J

E25

J×5

150mm

145mm

8

9

X1

H

X4

I

X25E

H

I

8

898

M4x11

Please make the groove on board 7 match with the part .

8

REMARK

D

12

13

X4D

X16

G

7

D×4

×16

G

Adjust screw to make hinge move backwards or forwards to the ideal placethen tighten

screw

9

HINGE ADJUSTMENT

If the door do not appear square or aligned,loosen or tighten the appropriate screws on each case

hinge as illustrated.

BC

2

DEPTH ADJUSTMENT

FOR-AND-AFT ADJUSTMENT

Loosen screw and screw ( Do not loose screw to the end), push hinge arm upwards or

backwards, re-tighten screw .

B

C C

C

1

C

1

Unbranded SXB056846 User manual

Unbranded SXB056846 User manual

Related papers

Other documents