DEVAISE ADYJ002 User manual

ADYJ002

Wood Printer Organizer with Shelf V3.1

GENERAL GUIDELINES

WARNINGS

Please read the following instruction carefully and use the product accordingly.

During assembly, keep parts and packaging materials away from children and pets as there

could cause injury and are a potential choking hazard.

Avoid sharp objects or corrosive chemicals to prevent damage to the product.

Please open the item slowly and cautiously to avoid pinching your hands by metal joints,

especially children.

If an odor is present when first opening the package, please leave the unwrapped product in

a shaded and ventilated area for a few days to air out.

Please follow the assembly instructions precisely and only use the product as intended.

Prior to assembly, please check the product for defects or missing accessories. If any

defects are found or accessories are missing, do not use product as damage or injury

may occur;

Please contact us for assistance and replacement.

It is suggested you regularly check the products bolts and connections to ensure safe use.

Assemble the item on a soft flat and clean surface to avoid scratches and damage.

It is recommended that two people assemble this product.

Please keep this manual and hand it over when you transfer the product.

This summary may not include every detail of all variations and considered steps.

Please contact us when further information and help are needed.

IMPORTANT INFORMATION

READ CAREFULLY.

KEEP THIS INFORMATION FOR FURTHER REFERENCE.

NOTES

If you have any further questions, please feel free to contact us

by email or official website: [email protected]

We will reply ASAP.

Enjoy your new purchase!

Before installation, please make sure you have all the hardware,

the serial numbers are properly labeled corresponging to the list,

and the quantity is correct.

1

EXPLODED DRAWING

PARTS

X16 X16

B

X16

C

A

X24

X2

F

D

X8

H

X2

E

X12

G

M4x11

M4x14

X2

J

X4

I

X8

KX1

L

L1 L2

1

2

10

5

7

8

4

6

3

9

2

1

MINIFIX POSITION

REMARK

X2

A

X4

B

REMARK

1. Please do not screw too deep or too shallow.

A

2. Put a blanket under the board to avoid scratch or damage.

DEV

V

ISE

214/

×2

A

4

×4

B

3

2

3

X4

B

REMARK

The innerside should be the edge banding side.

The position indicated by the finger on the side

without eccentric hole is correct .

5

4

B4

REMARK

4

X4

A

X8

B

4

5

X2

C

1

2

5

4

×2

C

A4

B8

5

REMARK

6X4

C

REMARK

C4

Please make sure the up side slot of

part 1 and 2 is on the same side.

1

2

5

4

The down should be the edge banding side.

UP

DOWN

6

REMARK

7

8

X10

A

X4

C

C4

Let the grooves on part 1and 2 be connected

to the groove on part 3 .

3

10

2

A10

1

7

9

10 X6

C

C6

10

1

2

7

2

10

8

11

12 X8H

M4x14

KDM4x11

X2

E

X2

F

X16

D

M4x11

×16

D

E

F

E

F

×8

H

9

13

14

2. Part 6 and 8 is adjustable shelf .

1. The long shadow part is in front

and the short one is inside.

REMARK

short

long

L1

L2

M4x14

KDM4x11

9

X4K

M4x14

X1L

X2J

J

H

JK4

3. Please make the groove on part 6 and 8 match with the part .

8

6

10

M4x14

KDM4x11

15

16

X8D

M4x11

X12

G

×12

G

D8

9

11

17

×4

+K

I

X4

I

K

M4x14

12

HINGE ADJUSTMENT

If the door do not appear square or aligned,loosen or tighten the appropriate screws on each case

hinge as illustrated.

Loosen screw ( Do not loose screw to the end), push hinge arm forwards or backwards,

re-tighten screw .

BB

1 2

DEPTH ADJUSTMENT

B

C

B

Adjust screw to make hinge move left or right to the ideal place

C

SIDE TO SIDE ADJUSTMENT

DEVAISE ADYJ002 User manual

DEVAISE ADYJ002 User manual

Related papers

Other documents