Lorex 4KHDIP86AD Quick start guide

Brand: Lorex

Model: 4KHDIP86AD

Category: Security camera accessories

Type: Quick start guide

This manual is also suitable for

4K IP Active Deterrence

Security Camera

Quick Start Guide

www.lorex.com

Safety Precautions

* Per camera in multi-camera packs

Package Contents

LNB8105X_QSG_EN_R1

Need Help?

Visit us online for up-to-date software and complete instruction manuals.

Click on the Downloads tab

Visit lorex.com

Search for the model number

of your product

Click on your product in the

search results

Installing the Camera

Ceiling mount / table top stand installation:

The camera includes a ceiling mount/table top stand and a wall mount. The ceiling

mount/table top stand may come pre-attached with the camera depending on the

camera conﬁguration. Follow the appropriate installation instructions below:

As our products are subject to continuous improvement, Lorex reserves the right to modify product design,

English Version 1.0

LNB8105X SERIES

• 4K IP Active Deterrence Security Camera

• Ceiling Mount / Table Top Stand*

• Wall Mount*

• Mounting Kit*

• Ethernet Extension Cable with Pre-attached RJ45 Cable Gland*

ATTENTION:

This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing

modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the

camera ﬁlter is working.

• Read this guide carefully and keep it for future reference.

• Follow all instructions for safe use of the product and handle with care.

• Use the camera within given temperature, humidity and voltage levels noted in the camera’s

speciﬁcations.

• Do not disassemble the camera.

• Do not point the camera directly towards the sun or a source of intense light.

• Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based

cleaners.

• The supplied cable is rated for surface and in-wall mounting only. Cables for

ﬂoor-to-ﬂoor installations are sold separately (CMR type). These and other cables are available

at lorex.com.

ATTENTION:

Test your camera prior to selecting a permanent mounting location by temporarily connecting the camera and cable

to your NVR.

For ceiling installation:

1. Remove the pre-inserted silicon plugs (4×) from the base (see

Figure 2).

2. Set the ceiling mount in the desired mounting position and mark

holes for screws and cables through the mounting base (or use

the included mounting template).

NOTE: Adjusting the angle of the camera is limited with this

installation. Ensure you angle the ceiling mount towards the

desired viewing area.

3. Drill holes where marked. If required, insert the included drywall anchors (4×).

4. Mount the ceiling mount to the mounting surface using the provided screws (4×).

Make sure all screws are fastened tightly.

For table top:

NOTES:

• You may choose to use the included wall mount for ceiling installation. Using the wall

mount for ceiling installation will provide more side-to-side angle adjustment but has

limited up/down adjustment. Prior to installation, ensure you test the camera view to

see which installation is the most appropriate based on your desired camera viewing

area. See “Wall mount installation” for more information.

• If the camera comes pre-attached with the ceiling mount/table top stand, detach it

from the camera.

1. With the adjustment ring securely fastened to the

bolt on the table top stand, screw the camera onto

the table top stand (see Figure 5).

NOTE: Skip this step if your camera has the ceiling

mount/table top stand pre-attached.

2. Connect cables as shown in the section “Connecting

the Camera”.

Adjustment

Ring

Adjustment

Knob

Mounting

Base

Dimensions

3.0”

75mm

3.8” / 98mm

4.7”

119mm

2.2”

56mm

Camera with Ceiling Mount / Table Top Stand

Camera with Wall Mount

3.0”

75mm

4.4” / 113mm

3.1”

78mm

Silicon

Plug

Figure 2

Adjustment

Ring

Figure 3

Silicon

Plug

Figure 4

5. With the adjustment ring securely fastened to the

bolt on the ceiling mount, screw the camera onto

the ceiling mount (see Figure 3).

6. Twist the camera onto the ceiling mount until the

camera is level, then tighten the adjustment ring.

7. Angle the camera up-and-down as needed. Remove the

pre-inserted silicon plug on the side of the ceiling mount

and tighten the screw using a Phillips screwdriver. Replace

the silicon plug (see Figure 4).

8. Feed the camera cable through the cable opening on the ceiling mount base and

the mounting surface or run the cables along the wall.

9. Connect cables as shown in the section “Connecting the Camera”.

Before Installing the Camera

• Decide whether to run the cables through the wall (drilling

required) or along the wall.

• (Optional) If you run the cables along the wall, use the

included cable guides with the cable guide screws and

optional drywall anchors as needed (see Figure 1).

Drywall

Anchor

Cable Guide

Screw

Cable Guide

Wall mount installation:

Decide whether to run the cables through the wall (drilling required) or along the wall.

Select one of the installation methods below based on cable run method.

NOTE: If the camera comes pre-attached with the ceiling mount/table top stand,

unscrew the camera from the ceiling mount/table top stand before following the steps

below.

Cable Notch

1. Set the wall mount base in the desired

mounting position and mark holes for

screws through the mounting base (or use

the included mounting template).

2. Drill the holes for the screws. Insert the

included drywall anchors (3×) if you are

mounting the camera onto drywall.

3. Mount the camera to the mounting surface

using the provided screws (3×). Make sure

all screws are fastened tightly.

4. With the adjustment ring securely fastened

to the bolt on the wall mount, screw the

camera onto the wall mount.

1. With the adjustment ring securely

fastened to the bolt on the wall mount,

screw the camera onto the wall mount.

2. Set the wall mount base in the desired

mounting position and mark holes for

screws through the mounting base (or

use the included mounting template).

3. Drill the holes for the screws and a hole

for the cables. Insert the included drywall

anchors (3×) if you are mounting the

camera onto drywall.

4. Connect cables as shown in the section

“Connecting the Camera”.

Running the cables along the wall Running the cables through the wall

5. Connect cables as shown in the section

“Connecting the Camera”.

6. Loosen the adjustment knob on the wall

mount base by turning it counter-clockwise.

Adjust the angle of the camera as needed

(see Figure 7).

7. Tighten the adjustment knob when

ﬁnished.

5. Feed the camera

cable through the

cable notch and the

mounting surface

(see Figure 6).

6. Mount the camera to the mounting

surface using the provided screws

(3×). Make sure all screws are fastened

tightly.

7. Loosen the adjustment knob on the

wall mount base by turning it counter-

clockwise. Adjust the angle of the camera

as needed (see Figure 7).

8. Tighten the adjustment knob when

ﬁnished.

NOTE: (Optional) Use the included cable guides

as needed to run the cables along the wall.

See “Before installing the camera” for more

information.

Figure 1

Figure 5

Figure 6

Figure 7

Using the RJ45 Cable Gland (Optional)

The RJ45 cable gland covers the camera’s Ethernet

connector and the RJ45 plug to provide weather-resistance

and protection from dust, dirt and other environmental

contaminants.

The RJ45 cable gland is pre-attached to the included

Ethernet extension cable.

Ethernet

Extension

Cable

RJ45 Cable Gland

To use the RJ45 cable gland:

Twist the RJ45 cable gland barrel securely onto the

camera Ethernet connector.

NOTE: The RJ45 cable gland is weather-resistant. Seal

the cap with silicone and/or electrical tape for additional

sealing if it will be exposed to precipitation regularly.

RJ45 Cable Gland

Barrel

Camera Ethernet

Connector

Installation Tips

• Point the camera where there is the least amount of obstructions

(i.e., tree branches).

• Install the camera where vandals cannot easily reach.

• This camera is rated for outdoor use. Installation in a sheltered location is recommended.

Problem Solution

No picture / signal • Ensure the camera is connected to a compatible NVR. For full camera

compatibility, visit lorex.com/compatibility.

• The camera may take up to 1 minute to power up after being connected to

the NVR.

• Ensure the camera is connected to your NVR or to your local network.

• If you are not using PoE, you must connect the camera to a 12V DC power

adapter (not included).

• If the camera is connected to the LAN, you must search your network for

cameras using the NVR. See the NVR’s instruction manual.

• Ensure your NVR is properly connected to a TV/monitor.

• There may be an issue with your extension cable run. Connect the camera

to the NVR using a different Ethernet cable.

Picture is too

bright

• Ensure your camera isn’t pointed directly at a source of light (e.g., sun or

spot light).

• Move your camera to a different location.

• Check the brightness and contrast settings on the NVR.

Picture is too dark • Check the brightness and contrast settings on the NVR.

Night vision is not

working

• The night vision activates when light levels drop. The area may have too

much light.

Picture is not clear • Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a

soft, clean cloth.

• Make sure that the cable run is within the limitations speciﬁed in the

section ‘Cable Extension Options’.

Bright spot in

video when viewing

camera at night

• Night vision reﬂects when pointing a camera through a window. Move the

camera to a different location.

No audio

• Audio is only supported on Lorex NVRs. For a list of compatible recorders,

visit lorex.com/compatibility.

• Ensure NVR volume is turned on / turned up.

• Ensure audio function on camera is turned on (see ‘Audio Settings’).

• Ensure audio is turned up on viewing device.

The camera

warning light is

not switching on

automatically

• Ensure that you have enabled and conﬁgured white light deterrence using

a compatible NVR. See your NVR’s documentation for more information.

• Ensure the active areas and schedule for white light deterrence are set

properly. The default schedule for the warning light is night times (between

5PM and 7AM).

The camera siren

is not switching on

automatically

• The camera siren cannot switch on automatically. You can control the

camera siren manually using the Lorex Cloud app or a compatible NVR.

Troubleshooting

LNB8105X_QSG_EN_R1

Connecting the Camera

Connect the Ethernet cable to the camera.

Connect the other end of the Ethernet cable

to the NVR’s PoE ports. The camera may

take a minute to power up after

being connected.

Connect the other end of the Ethernet cable

to a router or switch on your network. See

your NVR manual for details on connecting

the camera to your NVR using a switch or

router.

Camera

NVR

(Optional)

12V DC Power

NOTE: A 12V DC power adapter (model#:

ACCPWR12V1, not included) is only required if

connecting the camera’s Ethernet cable to a

router or switch that does not support PoE.

Ethernet Cable

Setup Diagram

Camera

HD NVR

Scenario 1: Connect Cameras to NVR

Scenario 2: Connect Cameras to Local Area Network (LAN)

Router

Camera

HD NVR

Router

PoE Switch

ATTENTION:

• This camera is only compatible with select NVRs. For a list of compatible recorders, visit

lorex.com/compatibility.

• For the smoothest possible 4K video streaming experience, connect your NVR to a Gigabit router (use

available 1000Mbps / 1Gbps Ethernet port). If you are connecting cameras to an external network switch, it

is recommended to use a 10/100/1000Mbps port on a Gigabit network switch.

Activating Deterrence

The camera’s deterrence features deter suspicious activities from occurring by ﬂashing

a warning light and/or sounding a siren from the camera. You can manually control these

features using the Lorex Cloud app. You can also conﬁgure automatic deterrence using

the Lorex Cloud app.

NOTES:

• See your NVR’s documentation for more information about enabling and automating

deterrence features using a compatible NVR.

• For a full list of compatible recorders, visit lorex.com/compatibility.

REQUIREMENTS:

• Connect the camera to a compatible NVR. See ‘Connecting the Camera’ section for

more information.

• Ensure the compatible NVR is set up remotely via the Lorex Cloud app. See your NVR’s

documentation for more information.

To activate deterrence manually through the Lorex Cloud app:

1. From live view, double-tap the deterrence camera to open the

channel in full screen.

2. Tap the deterrence icons on the camera display to switch on/

off the following deterrence features (see Figure 1):

A. Tap the icon to switch on (

) / off ( ) the camera

warning light.

B. Tap the icon to switch on (

) / off ( ) the camera siren.

NOTE: The camera warning light / siren will automatically

switch off after 10 seconds.

Audio Settings

ATTENTION:

Audio recording and listen-in audio are disabled by default. Audio recording and / or use of

listen-in audio without consent is illegal in certain jurisdictions. Lorex Corporation assumes no

liability for use of its products that does not conform with local laws.

To enable audio recording and listen-in audio through a Lorex NVR:

1. From Live View, right-click and click Main Menu. Enter the system user name (default:

admin) and password.

2. Click ( ) and select Recording > Recording.

3. Under Channel, select the channel where the

audio-capable camera is connected.

4. Under Audio/Video:

A. Check the box on the left to enable audio

recording and listen-in audio.

NOTE: Listen-in audio requires a monitor with

speakers or speakers connected to the NVR.

B. (Optional) Check the middle checkbox to

enable audio streaming to mobile applications.

5. Under Audio Encode, select the format

that will be used to record audio. G711A is

recommended.

6. Click OK to save changes.

A B

To enable / disable listening and talking through the Lorex

Cloud app:

NOTE: These instructions are based on current NVR interface. For the most up-to-date

instructions, see your NVR’s instruction manual on lorex.com.

1. From live view, double-tap the audio-capable camera to open the

channel in full screen.

2. Tap the following icons on the camera display to enable/disable

listening and talking through the Lorex Cloud app:

A. Tap the icon to enable ( ) / disable ( ) listening.

B. Tap the icon to enable (

) / disable ( ) talking.

REQUIREMENT: You must enable audio on the camera’s sub stream

through a connected NVR. Follow the above instructions for more

information.

A B

A. Reset Button: Use a Phillips screwdriver (not included)

to open the service compartment cover on top of the

camera. Press and hold the reset button for 5 seconds to

reset the camera to default settings.

B. Lens

C. Motion (PIR) Sensor

D. Microphone

E. Warning Lights

F. Speaker

Camera Overview

Disclaimers

• For a full list of compatible recorders, visit lorex.com/compatibility

• Not intended for submersion in water. Installation in a sheltered location recommended.

• This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/

Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is

normal, and indicates that the camera ﬁlter is working.

Cable Extension Options

Extend the cable run for your camera. Additional extension cables sold separately. See

table below:

Cable Type

Max Cable Run

Distance

Max # of Extensions

CAT5e (or higher) Ethernet cable

300ft (92m) 3

• You can use a RJ45 coupler or switch (not included) to connect male ends of Ethernet

cable together.

• To extend the cable run beyond 300ft (92m), a switch will be required (sold

separately).

To conﬁgure automatic deterrence through the Lorex Cloud app:

1. From live view, tap to access the Menu, and then tap Device Manager.

2. From the list of devices that appear, tap the device to which the deterrence camera

is connected.

3. Tap Settings > Video Detect > Deterrence.

• : Tap to add boxes to the active area.

• : Tap to remove boxes from the active area.

• : Tap and pinch the image to zoom in/out.

•

: Tap when ﬁnished.

In Figure 3 example, only motion in the parking lot will trigger

warning light.

Figure 1

4. Tap the channel of the deterrence camera to

conﬁgure. Do the following (see Figure 2):

A. Tap to enable/disable automatic warning light

deterrence.

B. Tap to view/hide advanced deterrence

conﬁguration options.

C. Tap Schedule to set a schedule during which

the warning light will automatically turn on.

NOTE: The default schedule is active during the

night, between 5pm and 7am.

D. Tap Area Setting to set the active area for

automatic deterrence. The camera image appears

with a grid of red boxes over top. The red area is

the active area for deterrence (see Figure 3).

5. Tap to save changes.

Figure 2

Figure 3

Lorex 4KHDIP86AD Quick start guide

Brand: Lorex

Model: 4KHDIP86AD

Category: Security camera accessories

Type: Quick start guide

This manual is also suitable for

Download PDF

report

Lorex 4KHDIP86AD Quick start guide

This manual is also suitable for

Lorex 4KHDIP86AD Quick start guide

Related papers

Other documents