Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Revision History UM015110-0508
ii
Revision History
Date
Revision
Level Description
Page
No
May
2008
10 Added Z8F6423FT020 to Introduction section.
Removed Application Notes from Documentation
section.
1
3
March 2008 09 Changed document title to Z8 Encore! XP
®
F64XX
Series Development Kit User Manual.
All
November
2007
08 Replaced Z8 Encore!
®
with Z8 Encore! XP
®
and
Z8 Encore!
®
64K Series MCUs with
Z8 Encore! XP
®
64K Series Flash Microcontrollers
throughout the document.
All
November
2007
07 Replaced ZiLOG with Zilog. Updated Zilog logo.
Updated Documentation and MCU sections.
All
3, 7
December
2006
06 Changed Figure 1 to Figure 2. 6
July 2006 05 Added reference to USB Smart Cable. 1
November
2005
04 Removed the word Preliminary from all page footers
and updated trademarks.
All
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Table of Contents UM015110-0508
iii
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Supported Host System Configuration . . . . . . . . . . . . . . . . . . 4
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
F64XX Series Development Board . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
IrDA Transceiver with Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . 9
External Interface Connectors JP1 and JP2 . . . . . . . . . . . . . . . 10
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Introduction UM015110-0508
1
Introduction
Zilog’s Z8 Encore! XP
®
F64XX Series MCUs are a part of the line of
Zilog
®
microcontroller products.
The Z8 Encore! XP F64XX Series Development Kit
(Z8F64200100KITG) allows you to get familiar with the hardware and
software tools available with this product. This kit consists of the
64 KB version of the Z8 Encore! XP Development Board that supports
and presents the features of the Z8 Encore! XP F64XX Series. The soft-
ware development tool kit allows you to write application software and
contains all supporting documents.
Z8F6423FT020 is the silicon used in the board. For more details, refer to
Z8 Encore! XP
®
F64XX Series Product Specification (PS0199) available
for download at www.zilog.com
.
This user manual acquaints you with the Z8 Encore! XP F64XX Series
Development Kit, and provides instructions on setting up and using the
tools to start building designs and applications.
Safeguards
The following precautions must be observed when working with the
devices described in this document.
Always use a grounding strap to prevent damage resulting from
electrostatic discharge (ESD).
Kit Contents
The Z8 Encore! XP F64XX Series Development Kit contains the
following hardware and software:
Caution:
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Introduction UM015110-0508
2
Hardware
The hardware in Z8 Encore! XP F64XX Series Development Kit
includes:
•
Z8 Encore! XP Z8F642 Development Board
•
USB Smart Cable for PC to Z8 Encore! XP
®
Z8F642 development
board (Previous versions of the development kit used a serial smart
cable. Refer your original documentation for information on using the
serial smart cable).
•
5 V DC power supply
Figure 1. Z8 Encore! XP MCU Development Kit Contents
(USB Smart Cable not shown)
Development
Board
Packaging
CD-ROM Containing
Documentation
Power
Supply
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Introduction UM015110-0508
3
Software (on CD-ROM)
The software in Z8 Encore! XP F64XX Series Development Kit includes:
•
ZDS II - Z8 Encore! IDE with ANSI C-Compiler
•
Sample code
•
Document browser
•
Acrobat Reader
Documentation
•
Z8 Encore! XP
®
F64XX Series Development Kit Quick Start Guide
(QS0028)
•
Z8 Encore! XP Z8F642 technical documentation (on CD-ROM):
– Z8 Encore! XP
®
F64XX Series Development Kit User Manual
(UM0151)
– Zilog Developer Studio II - Z8 Encore!
®
User Manual (UM0130)
–eZ8
TM
CPU User Manual (UM0128)
– Z8 Encore! XP
®
F64XX Series Product Specification (PS0199)
– Z8 Encore! XP
®
F64XX Series Product Brief (PB0124)
– Programmer’s Reference Sheet
The sample code is installed with ZDS II and resides in the
<installa-
tion directory>\samples
folder.
The documentation can be installed with the DemoShield interface or can
be viewed on the CD-ROM using the DemoShield menus and a PDF
reader. A copy of the Acrobat installer is provided on the CD-ROM and
can be installed from the DemoShield install screen. After installing the
documentation Windows Explorer can be used to select any document to
be viewed with PDF file viewer.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Introduction UM015110-0508
4
System/Software Requirements
IBM PC (or compatible computer) with the following minimum
configurations:
Supported Host System Configuration
•
Win98 Second Edition/WinNT 4.0 Service Pack 6 (USB Smart Cable
not supported)/Win2000 Service Pack 4/Windows XP Professional
•
PentiumII/233 MHz processor or higher up to Pentium IV, 2.8 GHz
•
96 MB RAM or more
•
25 MB hard disk space or more (no documentation)
•
Super VGA video adapter
•
CD-ROM
•
One or more RS-232 communication ports
•
USB high-speed port (when using USB Smart Cable)
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Installation UM015110-0508
5
Installation
Refer to the directions provided in the Quick Start guide for software
installation and setup of the Z8 Encore! XP
®
F64XX Series development
kit.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
F64XX Series Development Board UM015110-0508
6
F64XX Series Development Board
Introduction
The Z8 Encore! XP
®
F64XX Series development board is a development
and prototyping board for the Z8 Encore! XP Z8F642 microcontroller.
The board allows you to evaluate features of Z8 Encore! XP F64XX
Series and to develop an application before building the hardware.
Figure 2. Z8 Encore! XP F64XX Series Development Board
J1
P2
J2
TEST
RESET
LEDs
P1 Console
JP1
JP2
U4
Y1
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
F64XX Series Development Board UM015110-0508
7
Features
The features of Z8 Encore! XP F64XX Series development board
includes:
•
Z8 Encore! XP MCU
•
3 LEDs
•
RS-232 interface (P1)
•
IrDA transceiver (U4)
•
Two pushbuttons, RESET and TEST
•
5 V DC power connector (J1)
•
On-Chip Debugger interface (P2)
•
Crystal Oscillator (Y1)
•
Header for Analog-to-Digital Converter (ADC) input (J2)
•
Prototyping area
•
External interface connectors JP1 and JP2 (not populated)
MCU
The Z8 Encore! XP Z8F642 MCU is member of a family of Zilog
®
micro-
controller products based on Zilog’s 8-bit eZ8
TM
core CPU. The Flash
in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8
®
instructions. The rich peripheral set of the
Z8 Encore! XP Z8F642 makes it suitable for various applications includ-
ing motor control, security systems, home appliances, personal electronic
devices, and sensors.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
F64XX Series Development Board UM015110-0508
8
The development board contains circuitry to support and present all the
features of the Z8 Encore! XP
®
Z8F642. The main features of the
Z8 Encore! XP Z8F642 MCU are:
•
eZ8
TM
core CPU
•
Up to 64 KB of Flash memory with in-circuit programming capability
•
Up to 4 KB of register RAM
•
Either eight or twelve channels, 10-bit ADC
•
Two Full-duplex UART
•
I
2
C interface (Master Mode only)
•
Serial Peripheral Interface (SPI)
•
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
•
Three or four 16-bit timers with capture, compare, and PWM
capability
•
Watchdog Timer (WDT) with internal RC oscillator
•
Thirty one, forty six or sixty I/O pins
•
Programmable priority interrupts
•
On-Chip Debugger (OCD)
•
Voltage Brownout Protection (VBO)
•
Power-on Reset (POR)
•
2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs
•
Operating temperature: 20 °C ± 10 °C
For more information on the Z8 Encore! XP family of devices, refer to
Z8 Encore! XP
®
F64XX Series Product Specification (PS0199) available
for download at www.zilog.com
.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
F64XX Series Development Board UM015110-0508
9
IrDA Transceiver with Endec
The Z8 Encore! XP
®
Z8F642 contains a fully-functional, high-perfor-
mance UART with Infrared Encoder/Decoder (Endec). The Infrared
Endec is integrated with an on-chip UART to allow easy communication
between the Z8 Encore! XP Z8F642 and IrDA transceivers. Infrared com-
munication provides secure, reliable, low-cost, point-to-point communi-
cation between PCs, PDAs, cell phones, printers and other infrared
enabled devices.
Power and Communication Interfaces
Table 1 provides jumper information concerning the shunt status,
functions and devices affected by selected jumpers.
Table 1. Jumpers JP3 and JP4
Jumper Status
Device
Affected Status Default
JP3 OUT* IrDA
interface
Enable
JP3 IN IrDA
interface
Disable X
JP4** OUT* RS-232 Enable X
JP4 IN RS-232 Disable
* These jumpers must not be OUT at the same time.
** If the module is plugged onto an eZ80
®
Development platform or eZ80
demonstration board the local RS-232 can be disabled by connecting header JP2
pin 50 to the corresponding GND on the mating connector.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
F64XX Series Development Board UM015110-0508
10
External Interface Connectors JP1 and JP2
The external interface connectors are not populated when the board is
shipped. You can insert 0.1" space headers of choice.
Only Power and GND nets on connector JP1 are used on this module.
Note:
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Schematics UM015110-0508
11
Schematics
This section provides schematics for the Z8 Encore! XP
®
F64XX Series
Development Board.
12
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Schematics UM015110-0508
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
3.3 O
K
CONSO
LE
GND
USER
DBG
INTERFAC
E
DIS RS
232
DIS IR
DA
TEST
96
C0918-001
A
Encore! F642. Evaluation Module. Sche
matic.
B
12
Friday, June 06, 2003
Title
Siz
e
Document Number
Rev
Date:
Sheet
of
TXD0
CTS0
RXD
0
5V
VCC_5V
VCC_33V
DBG
PA4_RXD
0
PA5_T
XD0
VCC_33V
PA3_CTS
0
GND
VCC_33V
PA5_T
XD0
PA4_RXD
0
GND
GND
GND
VCC_33V
GND
VCC_33V
GND
GND
VCC_33V
VCC_33V
IRDA_SD
GND
VCC_33V
GND
PA3_CTS
0
VCC_5V
VCC_33V
DBG
-DIS_IRDA
-DIS_232
PA5_TX
D0
PA4_RXD
0
PA0_T0IN
PA1
_T0OUT
PA2
PC0_T1IN
C3
0.1uF
R4
68
D2
RED
21
R19
10K
SW1
C4
0.1uF
R10
10
0
U3A
74LVC04/SO_1
1 2
147
R5
10
0
C7
0.1uF
JP4
1
2
U3D
74LVC04/SO_1
9 8
147
P2
Header 3x2
12
34
56
R2
10K
R6
100K
U2
LT1086-3.3/TO
220
1
3 2
GND
VIN
VOUT
D4
GREEN
21
R9
10
0
R16
10K
C1
0.1uF
C6
0.1uF
JP3
1
2
C10
330nF
U3E
74LVC04/SO_1
11 10
147
R1
68
0
U3B
74LVC04/SO_1
3 4
147
R7
2R7
R17
10K
C5
0.1uF
J1
PWR JACK
2
3
1
U4
ZHX181
0
2
4
3
1
5
6
0
TXD
SD
RXD
LEDA
VCC
GND
T
D3
YELL
21
+
C8
100/10
C9
0.1uF
R8
10K
+
C2
100/10
F1
RXE110
P1
DB9 Female
5
9
4
8
3
7
2
6
1
U3F
74LVC04/SO_1
13 12
147
R18
10K
U1
MAX322
2
1
2
4
5
6
13
12
15
10
3
7
17
8
16
9
20
1918
11
14
EN
C1+
C1-
C2+
C2-
T1IN
T2IN
R1OUT
R2OUT
V+
V-
T1OUT
T2OUT
R1IN
R2IN
SHDN
VCCGND
NC
NC
TP
1
1
2
3
4
5
R11
10K
D1
LED
21
U3C
74LVC04/SO_1
5 6
147
R3
100
TP2
1
2
3
4
5
Figure 3. Z8 Encore! XP F64XX Series Development Board
13
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Schematics UM015110-0508
Figure 4. Z8 Encore! XP F64XX Series Development Board (Continued)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
connector
2
connector
1
for
referenc
e
only
If Module is plugged onto the De
v Platform the local
RS232 interface is disabled
by pin 50 of JP2
RESET
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
96C
0918-001
A
Encore! F642. Evaluation Module. Sche
matic.
B
22
Friday, June 06, 2003
Title
Siz
e
Document Number
Rev
Date:
Sheet
of
PB7_ANA7 PB3_ANA3
VCC_33V
PH3_ANA11
VREF
PB2_ANA2
XOUT
DBG
A20
-CS0
A12
-IOREQ
-F91_WE
A13
GND
GND
A17
A21
VCC_33V
A14
D1
VCC_33V
D7
-DIS_FLASH
GND
A6
A0
D3
D6
-BUSACK
A3
D2
VCC_33V
A15
A4
-TRS
TN
D0
-MREQ
A7
A10
A9
A16A18
A11
-INSTRD
A19
A5
GND
D5
-CS1
A22
A1A2
-CS2
-RD
A8
GND
D4
A23
-WR
-BUSREQ
GND
PA7_SDA
PA3_CTS
0
PC2_SS
VCC_33V
PC4_MOSI
VCC_33V
PC1_T1O
UT
PC0_T1IN
PA2
PA1
_T0OUT
GND
GND
PC5_MISO
PA4_RXD
0
PA5_TX
D0
-RESE
T
GND
GND
PA6_SCL
PA0_T0IN
PC3_SCK
GND
VCC_33V
-DIS_IrDA
PA1_T0OUT
PA3_CTS0
PF7
PC4_MOSI
PC5_MISO
PD4_RXD1
PD3
PD5_TXD1
VCC_33V
GND
PA5_TXD0
PA4_RXD0
PA6_SCL
PA0_T0IN
PD2
PC2_SS
PB0_ANA0
VREF
AGND
PB2_ANA2
PH0_ANA8
AVDD
PH1_ANA9
PB6_ANA6
PB4_ANA4
PH3_ANA11
PB7_ANA7
PB3_ANA3
PB1_ANA1
PB5_ANA5
PH2_ANA10
PF6
PF5
PF4
PE4
PF3
PE3
PD1_T3O
UT
XIN
PD0_T3IN
PE2
PF1
PE1
PE0
PF0
PF2
PE5
PC6_T2IN
PC7_T2O
UT
PE7
PE6
PA7_SDA
PG6
PG4
DBG
PD6_CTS1
PC1_T1O
UT
PG2
PD7_RCOUT
PG3
PC3_SCK
PG1
PG5
PG0
PG7
PC0_T1IN
GND
-RESET
PB4_ANA4
PH1_ANA9
PD
5_TXD1
PD4_RXD1
PD6_CTS1
PE1 PE0
PE3
PE5
PE7
PE2
PE4
PE6
PF0
PD7_RCOUT
PG0
PD2
PD0_T3IN
PC6_T2IN
PD3
PD1_T3O
UT
PC7_T2O
UT
PA5_T
XD0
PA3_CTS
0
PA4_RXD
0
PB5_ANA5
PH2_ANA10
VCC_33V
GND
VCC_33V
GND
VCC_33V
GND
VCC_33V
VCC_33V
GND
GND
PB6_ANA6PB1_ANA1
PH0_ANA8
PB0_ANA0
PB0_ANA0
PB7_ANA7
PH1_ANA9
PB3_ANA3
PB6_ANA6
PB1_ANA1
PB2_ANA2
PB5_ANA5
PB4_ANA4
PH0_ANA8
PH2_ANA10
PH3_ANA11
PG4
PG3
PG1
PG2
AVDD
GND
AGND
VREF
PA2
PF7
PF6
PF5
PF4
PF3
PF2
PF1
PG5
PG6
PG7
AGND
GND
VCC_33V
DBG
VCC_33V
-DIS_IRDA
-DIS_232
PA3_CTS
0
PA5_TX
D0
PA4_RXD
0
PA2
PA0_T0IN
PA1
_T0OUT
PC0_T1IN
C24
18pF
JP14
Header 1
1
C15
0.001uF
C21
0.1uF
C37
0.001uF
JP19
Header 1
1
JP9
Header 1
1
C14
0.001uF
C27
0.001uF
Y1
18.432MHz
C19
0.001uF
JP20
Header 1
1
SW2
C13
0.1uF
JP10
Header 1
1
C32
0.001uF
R13
100K
C18
0.001uF
JP15
Header 1
1
L1
EMI Filter
1
2
3
IO
GND
IO
J2
1
3
5
7
9
11
13
15
17
19
21
23
25
2
4
6
8
10
12
14
16
18
20
22
24
26
C36
0.001uF
C26
0.001uF
JP21
Header 1
1
C12
0.1uF
C33
0.001uF
C28
0.001uF
JP16
Header 1
1
JP6
Header 1
1
C22
0.001uF
C34
0.001uF
C38
0.01uF
C30
0.001uF
C16
0.1uF
+
C25
22uF
JP17
Header 1
1
JP2
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
R12
220
JP7
Header 1
1
C23
18pF
C11
0.001uF
U6
Z8F642
1
2
3
4
5
6
7
8
9
11
10
12
13
14
15
16
17
18
19
20
21
22
23
24
80
65
64
25
40
41
26
27
28
29
30
31
32
33
34
35
36
37
38
39
42
43
44
45
46
47
48
49
50
51
52
54
55
56
57
58
60
61
62
63
66
67
70
71
72
73
74
75
78
79
77
76
68
69
59
53
PA0/T0IN
PD2
PC2/SS
PF6
RESET
VDD
PF5
PF4
PF3
PE3
PE4
GND
PE2
PE1
PE0
GND
PF2
PF1
PF0
VDD
PD1/T3OUT
PD0/T3IN
XOUT
XIN
PA1/T0OUT
PA6/SCL
PA7/SDA
GND
AGND
GND
AVDD
PH0/ALG8
PH1/ALG9
PB0/ALG0
PB1/ALG1
PB4/ALG4
PB5/ALG5
PB6/ALG6
PB7/ALG7
PB3/ALG3
PB2/ALG2
PH2/ALG10
PH3/ALG11
VREF
PC0/T1IN
PC1/T1OUT
DBG
PC6/T2IN
PC7/T2OUT
PG7
VDD
PG6
PG5
PG4
PG3
PE7
PE6
PE5
PG2
PG1
PG0
PD7/RCOUT
PC3/SCK
PD6/CTS1
PA5/TXD0
PA4/RXD0
PC4/MOSI
PD5/TXD1
PD4/RXD1
PD3
PC5/MISO
PF7
PA3/CTS0
PA2
GND
VDD
GND
VDD
GND
VDD
JP13
Header 1
1
C17
0.1uF
C35
0.001uF
C29
0.001uF
C31
0.001uF
JP1
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
JP18
Header 1
1
C20
0.1uF
JP8
Header 1
1
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Customer Support UM015110-0508
14
Customer Support
For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at:
h
ttp://www.zilog.com/kb.
For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at:
h
ttp://support.zilog.com.
Z8 Encore! XP
®
F64XX Series Development Kit
User Manual
Disclaimer UM015110-0508
15
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2008 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, eZ8, Z8 Encore! XP, Z8 Encore! MC, Crimzon, eZ80, and ZNEO are
trademarks or registered trademarks of Zilog, Inc. All other product or service names are
the property of their respective owners.
Warning:
Authorized Distribution Brand：
Website：
Welcome to visit www.ameya360.com
Contact Us：
Address：
401 Building No.5, JiuGe Business Center, Lane 2301, Yishan Rd
Minhang District, Shanghai , China
Sales：
Direct +86 (21) 6401-6692
Email [email protected]
QQ 800077892
Skype ameyasales1 ameyasales2
Customer Service：
Email [email protected]
Partnership：
Tel +86 (21) 64016692-8333
Email [email protected]
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ACTiSYS IR8250PEK Quick start guide
-
Conceptronic C30-001 Datasheet
-
Digi Color Touchscreen Application Kit Quick start guide
-
Digi RCM3600 User manual
-
Soleus Air PH1-14R-03 User manual
-
Digi ZigBee Application Kit Quick start guide
-
-
Digi Camera Interface Application Kit Quick start guide
-
ADC Switch Z8F04A08100KIT User manual
-
Digi Bluetooth Application Kit User manual
