Acuity Controls nLight ECLYPSE Safety Instructions

Brand: Acuity Controls

Model: nLight ECLYPSE

Type: Safety Instructions

nLight ECLYPSE Enclosure

912-00023-001

Page 1

Always read complete installation instructions prior to installation!

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

All servicing should be performed by qualiﬁed service personnel.

When using electrical equipment, basic safety precautions should always be followed including the

following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

Do not use outdoors.

Do not mount near gas or electric heaters.

Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS.

Remove internal assembly prior to drilling/punching additional or larger holes for conduits, and

remove excess metal shavings and contaminants prior to powering the panel

Acuity Controls assumes no responsibility for claims arising out of improper or careless installation or handling of this product. Failure to follow any of

these instructions could void product warranty.

For a complete listing of product Terms and Conditions, please visit www.AcuityControls.com

nLight ECLYPSE Enclosure

SURFACE MOUNT ENCLOSURE WITH SCREW COVER

TO REMOVE RELAY PANEL COVER:

1) UNFASTEN FOUR PHILLIPS SCREWS AT CORNERS OF COVER

2) REMOVE COVER FROM RIGHT EDGE AND ENGAGEMENT FEATURES ON LEFT SIDE WILL RELEASE

TO INSTALL THE PANEL COVER:

1) HOOK IN THE ENGAGEMENT FEATURES ON THE LEFT FROM THE OUTSIDE

2) FASTEN THE FOUR PHILLIPS SCREWS AT THE CORNERS OF THE COVER

Note: If cover hardware is misplaced, utilize screws and lockwashers with paint-piercing features. Enclosure

utilizes "SEMS" and "KEPS" fasteners with integrated toothed lock washers for paint piercing to ensure proper

bonding of painted enclosure parts.

ENCLOSURE UNTILIZES "SEMS" AND "KEPS" FASTENERS:

INTEGRATED TOOTHED LOCK WASHERS FOR PAINT

PIERCING TO ENSURE PROPER BONDING OF PAINTED

ENCLOSURE PARTS.

912-00023-001

Page 2

ENCLOSURE MOUNTING INSTRUCTIONS

nLight ECLYPSE Enclosure

12"

12 3/4"

8-Relay

Panel

20 3/4"

16-Relay

Panel

3/4"

1 1/8" 1 1/8"

3/4"

14 1/4"

2 1/8"

TYP

10" TYP

1 5/16"

TYP

14 1/4"

8-Relay

Panel

22 1/4"

16-Relay

Panel

5/8"

3/4"

n9/32" Mounting Holes

4 Places

All knockouts are dual

concentric style for 1/2"

& 3/4" trade size fittings

For Flush Mount Installations:

Alignment markings on all sides for 5/8" & 3/4" thick wallboards.

Align with stud surfaces for proper protrusion of box edge to be

flush finished wall surface. Verify with actual wall material

thicknesses to ensure a proper finished installation.

wall

stud

wall board

align marks with wall stud surface

for flush mount installs

Flush Mount

Install example

Flush

8-RELAY SIZED PANEL SHOWN, BUT APPLIES TO 16-RELAY VERSION

Box Dimensions & Installation Application Notes

TOP

912-00023-001

Page 3

SURFACE MOUNT ENCLOSURE MOUNTING AND KNOCKOUT DIMENSIONS

nLight ECLYPSE Enclosure

912-00023-001

Page 4

BOX DIMENSIONS & INSTALLATION APPLICATION NOTES

The NECY enclosure was designed with minimal knockouts to provide installers the freedom to add additional conduit feeds to

better meet speciﬁc site conditions without locking them into conﬁned positions or preset trade size ﬁttings.

The dimensions provided are for reference only. Verify all clearances with the actual panel and its components in place prior to

performing any added punch-out work. Note: For Canadian conﬁgured devices with step-down transformers (for 347V), added

conduit feed access is more constricted as shown by the added step-down transformer.

WIRING INSTRUCTIONS

DE-ENERGIZE THE PANEL BEFORE MAKING ANY WIRING

CONNECTIONS.

DO NOT DISCARD THESE INSTALLATION INSTRUCTIONS.

PLEASE KEEP FOR FUTURE REFERENCE AND OPERATION

INFORMATION.

NOTE: Make certain that high voltage and low voltage

wiring enters the enclosure separately.

High Voltage wiring should be brought into the upper-

right section of the enclosure, inside the high-voltage

compartment.

Low Voltage wire should enter in the low voltage wiring

areas of the enclosure.

Failure to separate high voltage from low voltage wiring

may cause electrical interference.

HIGH VOLTAGE CONNECTIONS

• Always de energize panel before wiring.

• Use only at the listed voltage per panel specs

• All installation service must be performed by qualiﬁed

personnel.

WIRING THE POWER SUPPLY

• The Acuity Relay Panel is factory conﬁgured with a 120-

277V 50W switching power supply (MVOLT) , and optionally

can be supplied with a 347V to 277V step-down transformer

(CNDV).

• Connect wires to the power supply. You must provide

a dedicated circuit with circuit protection for the power

supply. Earth ground must be connected to the lug labeled

"FOR EQUIPMENT GROUNDING ONLY," located in the high

voltage compartment

• It is recommended that all low voltage wiring be done

with power removed from the system, to protect from

potential shorts during the wiring process.

• All low voltage wiring must be run in separate conduit

from line voltage wiring. DO NOT MIX CLASS 1 AND CLASS 2

CIRCUITS IN THE SAME CONDUIT

• Test all low voltage wiring for shorts to AC ground before

connection to the controller.

APPLYING POWER

• Once the wiring is complete, make certain that the

enclosure is clean of any wire clippings and that no

fragments are present.

• Ensure that there are no loose wires or exposed wires that

could short to other wires or components.

• Power up the unit from the circuit breaker.

a) The green power supply input terminal block receives

the line voltage feed wires, 120-277VAC, Neutral,

Ground

nLight ECLYPSE Enclosure

912-00023-001

Page 5

Knockout Knockout (High Voltage)

Knockout Knockout

nLight Port 1

nLight Port 2

USB 1

USB 2

DIN Rail

DIN Clip

nLight Port 3

(Supports

GFX module)

Ethernet Secondary

Ethernet Primary

Modbus

RS-485

nLIGHT ECLYPSE WIRING DIAGRAM

Acuity Controls nLight ECLYPSE Safety Instructions

Brand: Acuity Controls

Model: nLight ECLYPSE

Type: Safety Instructions

Download PDF

report

Acuity Controls nLight ECLYPSE Safety Instructions

Acuity Controls nLight ECLYPSE Safety Instructions

Related papers

Other documents