Highwood AD-ST7HM2CO4BA-ACE Operating instructions

Type
Operating instructions
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 1 OF 1
IMPORTANT!
DO NOT fully tighten the nuts until all
nuts are started. Once all nuts are started,
go back & tighten all the nuts.
Retain these instructions for future reference
HARDWARE
high
wood
NATURE'S CLOSEST RIVAL
INCLUDED TOOLS
5/32" HEX KEY
Lehigh, Weatherly, or Adirondack Collection
Rectangular, Square, or Sideboard Tables
Assembly Guide
All AD-DTB/AD-CTB
08.07.2017
A
x8
1/4"-20 x 3" Bolt
This assembly guide applies to all tables displayed above!
- AD-DTB37/AD-CTB37 - Rectangular 36x72 Dining or Counter Height Dining Table
- AD-DTB47/AD-CTB47 - Rectangular 42x72 Dining or Counter Height Dining Table
- AD-DTB48/AD-CTB48 - Rectangular 42x84 Dining or Counter Height Dining Table
- AD-DTB25/AD-CTB25 - 22x54 Sideboard
or Counter Height Sideboard Table
- AD-DTB44/AD-CTB44 - 42x42 Square
Dining or Counter Height Dining Table
B
x1
2" Umbrella Grommet
A
C
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 2 OF 2
high
wood
NATURE'S CLOSEST RIVAL
Lehigh, Weatherly, or Adirondack Collection
Rectangular, Square, or Sideboard Tables
Assembly Guide
All AD-DTB/AD-CTB
08.07.2017
A
1) Place the table top upside down on a soft surface.
2) Attach leg with 2 A bolts.
3) Repeat for each leg.
4) Securely tighten all bolts, but do not over tighten.
5) If installing an umbrella, insert
Umbrella Grommet B into center hole.
B
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 1 OF 2
INCLUDED TOOLS
5/32" HEX KEY
IMPORTANT!
DO NOT fully tighten the bolts until all
bolts are started. Once all bolts are inserted,
go back & tighten all the bolts.
Retain these instructions for future reference
HARDWARE
high
wood
NATURE'S CLOSEST RIVAL
Adirondack Collection
Hamilton Counter Deck Chair
Assembly Guide
1) Insert an A bolt into lower hole to on each side
attach Seat to Back. Make sure the back is fully upright.
Make bolts snug, but do not overtighten.
AD-CHCA2
10.13.16
A
x18
1/4"-20 x 1-3/4"
A
A
RIGHT LEG
SEAT
2) Attach Right Leg to
Seat using three A bolts.
Note: arm above back support
DETAIL A
SCALE 0.16 : 1
C
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 2 OF 2
high
wood
NATURE'S CLOSEST RIVAL
Adirondack Collection
Hamilton Counter Deck Chair
Assembly Guide
AD-CHCA2
10.13.16
3) Attach Footrest to Right Leg using 4 A bolts.
4) Flip chair and lay on right side.
Repeat steps 2 and 3 for Left Leg.
5) Attach arms to the back using 2 A bolts.
6) Tighten all bolts. Enjoy your highwood chair!
A
Note: Footrest faces front of chair
RIGHT LEG
ARM
BACK
FOOTREST
A
Note: Two bolts insert here
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Highwood AD-ST7HM2CO4BA-ACE Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI