ASSEMBLY INSTRUCTIONS
JJ
Connect chair back (A) with seat base (B) and armrests (C and D).
M6*30 bolts (I) are used. Please do not tighten bolts to the end at this step.
Connect chair seat support beams (G) with backrest (C and D).
M6*15 bolts (H) are used. Please do not tighten bolts to the end at this step.
Connect chair seat support frame (E) with seat base (B). M8*20 bolts (J) are used.
Please tighten bolts to the end at this step.
Insert the assemblied chair seat part into swivel base (F).
Stick the hook & loop velcro
of backrest and seat board.
Finish and enjoy your chair.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
A
B
C
D
E
F
G
H
I
J
K
L
1
1
1
1
1
1
2
8
8
4
1
1
M6*15
M6*30
M8*20
Part # Reference Image QTY
A
C
B
I
D
I
G
HH
E
F
ASSEMBLY TIPS: Please use the hardware and accessories included in the set. DO NOT use other electrical or manual tools.
In order to facilitate the assembly and make your final product firm and stable, please tighten by a few rounds each screw one by one.
The assembly requires minimal level of DIY skills if you follow the instructions carefully. In case you encounter any difficulty or have any questions, feel free to contact
the store or manufacturer.
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS: Please use the hardware and accessories included in the set. DO NOT use other electrical or manual tools.
In order to facilitate the assembly and make your final product firm and stable, please tighten by a few rounds each screw one by one.
The assembly requires minimal level of DIY skills if you follow the instructions carefully. In case you encounter any difficulty or have any questions, feel free to contact
the store or manufacturer.
STEP 1
STEP 2
STEP 3
Connect chair back (A) with seat base (B) and armrests (C and D).
M6*30 bolts (I) are used. Please do not tighten bolts to the end at this step.
Connect chair seat board (B) with armrests (C and D). M6*30 bolts (G) are used.
Please do not tighten bolts to the end at this step.
Connect chair seat support beams (E) with armrests (C and D).
M6*15 bolts are used. Please do not tighten bolts to the end at this step.
Stick the hook & loop velcro
of backrest and seat board.
Finish and enjoy your chair.
Part # Reference Image QTY
A
B
C
D
E
F
G
H
1
1
1
1
2
8
8
1
M6*15
M6*30
C
B
D
G
A
G
F F
E
E
F F
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS: Please use the hardware and accessories included in the
set. DO NOT use other electrical or manual tools.
In order to facilitate the assembly and make your final product firm and
stable, please tighten by a few rounds each screw one by one. After all
screws are connected, then you start to tighten each screw to the end.
DO NOT tighten any screw to the end before you’ve connected all screws.
The assembly requires minimal level of DIY skills if you follow the instruc-
tions carefully. In case you encounter any difficulty or have any questions,
feel free to contact the store or manufacturer.
STEP 1
STEP 2
STEP 3
1
1
Part # Reference Image QTY
A
B
C
D
E
F
1
4
1
16
M6*20
Place table board (A) on the ground, then screw table legs (B) to it.
Please do not tight any screws to the end at this step.
B
A
E
E
EE
C
Screw table leg support ring (C) to table legs.
Make sure all screws are connect properly and tighten all screws to the end.
Place umbrella hole lid (D) properly.
D
Finish and enjoy your table.
/
