ASSEMBLY INSTRUCTIONS
Assembly Tips: Please use the hardware and accessories included in the set. DO NOT use other electrical or
manual tools.
In order to facilitate the assembly and make your final product firm and stable, please tighten by a few rounds each
screw one by one.
The assembly requires minimal level of DIY skills if you follow the instructions carefully. In case you encounter any
difficulty or have any questions, feel free to contact the store or manufacturer.
Part # Reference Image QTY
A
B
C
D
E
F
G
H
I
1
1
1
1
1
4
2
4
1
STEP 1
STEP 2
STEP 3
Connect chair back (A) with seat base (B) and armrests (C and D).
M6*20 bolts (F) and M6*30 bolts (H) are used.
Please do not tighten bolts to the end at this step.
Connect chair leg support beam (E) with legs. M6*25 (G) are used.
Make sure all bolts are inserted properly, then tighten all bolts to the end.
Finish and enjoy you chair.
M6*20
M6*25
M6*30
F
A
C
B
D
H
Stick the hook & loop velcro
of backrest and seat board.
E
G
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS: Please use the hardware and accessories included in the set. DO NOT use other electrical or manual tools.
In order to facilitate the assembly and make your final product firm and stable, please tighten by a few rounds each screw one by one.
The assembly requires minimal level of DIY skills if you follow the instructions carefully. In case you encounter any difficulty or have any questions, feel free to
contact the store or manufacturer.
Screw chair back (A) to seat board (B). M6*15 bolts (G) are used.
Please tight screws to the end.
Screw chair armrest (C and D) to chair back (A) and seat board (B).
M6*15 bolts (G) and M6*30 (H) are used.
Please do not tighten screws to the end at this step.
Place chair support beam (E) in the between of chair armrests properly
and screw it. M6*15 (G) bolts are used.
Please do not tighten any screws to the end at this step.
Connect chair gliding base (F) to armrests with washers (J) and M6*18
countersunk
bolts (I).
Make sure all bolts are connected properly, then tighten all screws to the end.
Stick the hook & loop velcro
of backrest and seat board.
STEP 1
STEP 2
STEP 3
STEP 4
Finish and enjoy your chair.
Part # Reference Image QTY
A
B
C
D
E
F
G
H
I
J
K
1
1
1
1
1
1
7
6
4
4
1
M6*15
M6*30
M6*18
Countersunk Bolt
B
A
G
G
C
D
H
HH
E
GG
F
IJ
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS: Please use the hardware and accessories included in the
set. DO NOT use other electrical or manual tools.
In order to facilitate the assembly and make your final product firm and
stable, please tighten by a few rounds each screw one by one. After all
screws are connected, then you start to tighten each screw to the end.
DO NOT tighten any screw to the end before you’ve connected all screws.
The assembly requires minimal level of DIY skills if you follow the
instructions carefully. In case you encounter any difficulty or have any
questions, feel free to contact the store or manufacturer.
B
A
C
D
E
F
1
4
1
12
1
3
M6*20
STEP 1
STEP 2
STEP 3
STEP 4
Part # Reference Image QTY
Place table top frame (A) on the ground, then screw table legs (B) to it.
Please do not tight any screws to the end at this step.
Screw table leg support ring (C) to table legs.
Make sure all screws are inserted properly and tighten all screws to the end.
Place table top tiles (D) on the table frame properly.
Finish and enjoy your table!
B
E
E
E
C
D
A
/
