Tyan S5151 User manual

Tomcat i7221A S5151 User’

s Manual

i

http://www.tyan.com

Tomcat i7221A

///

S5151

Revision 1.0

manual may be reproduced or translated without prior written consent from TYAN Computer

Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tomcat, i7221 and S5151 are trademarks of TYAN Computer Corporation.

Intel Prescott and combinations thereof are trademarks of Intel Corporation.

Promise is a trademark of Promise Technology, Inc.

Award, AwardBIOS are trademarks of Award Software Incorporated.

Microsoft and Windows are trademarks of Microsoft Corporation.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

SMSC is a trademark of Standard Microsystems Corporation.

Broadcom is a trademark of Broadcom Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has

been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose or

merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Tomcat i7221A S5151

Table of Contents

ii

http://www.tyan.com

Table of Contents

Before you begin….................................................................................................................v

Chapter 1: Introduction..........................................................................................................1

1.1 Congratulations!...........................................................................................................1

1.2 Hardware Specifications..............................................................................................1

Chapter 2: Board Installation.................................................................................................1

2.1 Installing the Motherboard............................................................................................1

2.1.1 Installation Notes ...............................................................................................1

2.2 Board Image ................................................................................................................2

2.3 Block Diagram..............................................................................................................3

2.4 Motherboard Components ...........................................................................................4

2.5 Jumpers and Connectors.............................................................................................5

2.5.1 Com Port: J5......................................................................................................6

2.5.2 SO-DIMM Socket: J12.......................................................................................6

2.5.3 Serial ATA RAID Connectors: J20/J21/J22/J23 (SATA1 / SATA2 / SATA3 /

SATA4).......................................................................................................................7

2.5.4 LAN1/LAN2/LAN3 Disabled Headers: JP2/JP1/JP3..........................................7

2.5.5 Front Panel LAN1/LAN2 Link and Active LED Connectors: JP5/JP6.................8

2.5.6 Front Panel LAN1/LAN2 Speed LED Pin-Headers: JP4/JP7 .............................8

2.5.7 Front Fan Connectors: JP17/JP18/JP23............................................................9

2.5.8 Chassis Fan Connector: JP8.............................................................................9

2.5.9 CPU Fan Connector: JP22 ..............................................................................10

2.5.10 Front Panel USB 2.0 Connectors: JP12/JP13 ...............................................10

2.5.11 Clear CMOS Jumper: JP15 ...........................................................................11

2.5.12 Front Panel System Connector: JP16............................................................11

2.5.13 SMDC Connector: JP20 ................................................................................12

2.5.14 PCI-X Speed Select Header: JP14................................................................12

2.5.15 SMDC/ASF2.0 Select Headers:JP24/JP25....................................................13

2.6 Mounting the Motherboard.........................................................................................14

2.7 Installing Memory.......................................................................................................15

2.7.1 Memory Installation Procedure........................................................................16

2.8 Installing the Processor and Cooling Fan...................................................................17

2.9 Installing Drive Cables ...............................................................................................20

2.10 Installing Expansion Cards.......................................................................................21

2.11 Connecting External Devices...................................................................................21

2.11.1 Onboard LAN LED Color Definition ...............................................................22

2.12 Installing the Power Supply......................................................................................22

2.13 Finishing Up .............................................................................................................23

Chapter 3: BIOS Setup............................................................................................................1

3.1 About the BIOS............................................................................................................1

3.1.1 Starting Setup....................................................................................................1

3.1.2 Setup Basics......................................................................................................1

3.1.3 Getting Help.......................................................................................................1

3.1.4 In Case of Problems ..........................................................................................2

3.1.5 Setup Variations................................................................................................2

3.2 Main BIOS Setup .........................................................................................................2

3.3 Standard CMOS Features............................................................................................4

3.4 Advanced BIOS Features............................................................................................5

3.4.1 CPU Features....................................................................................................7

3.4.2 Boot Sequence................................................................................................10

3.4.3 Console Redirection........................................................................................12

3.5 Advanced Chipsets Features.....................................................................................12

3.5.1 PCI Express Root Port Function......................................................................14

Tomcat i7221A S5151

Table of Contents

iii

http://www.tyan.com

3.6 Integrated Peripherals................................................................................................16

3.6.1 OnChip IDE Device..........................................................................................16

3.6.2 Onboard Device...............................................................................................18

3.6.3 Super IO Device..............................................................................................20

3.7 Power Management Setup.........................................................................................22

3.7.2 Power On Setup..............................................................................................24

3.7.3 Reload Global Timer Events............................................................................25

3.8 PnP/PCI Configurations.............................................................................................26

3.8.1 IRQ Resources................................................................................................27

3.9 PC Health Status .......................................................................................................28

3.10 Frequency/Voltage Control......................................................................................28

3.11 Load Fail-Safe Defaults............................................................................................30

3.12 Load Optimized Defaults..........................................................................................30

3.13 Supervisor/User Password Setting...........................................................................31

3.14 Save & Exit Setup....................................................................................................32

3.15 Exit Without Saving..................................................................................................32

Chapter 4: SATA/RAID Setup (for SATA RAID model).........................................................1

4.1 Configuring BIOS for Intel RAID for Serial ATA on board.............................................1

4.1.1 Creating, Deleting, and Resetting RAID Sets ....................................................1

4.1.2 Create RAID 0 or RAID 1 Volume......................................................................1

4.1.3 Delete RAID Volume..........................................................................................2

4.1.4 Reset RAID Data...............................................................................................2

4.2 Loading the Intel Application Accelerator RAID Edition Driver During Operating

System Install.....................................................................................................................2

4.2.1 Instructions on Creating F6 Floppy Diskette......................................................2

4.2.2 Installation Using F6 Method .............................................................................3

4.3 Intel RAID Option ROM................................................................................................4

4.3.1 Description.........................................................................................................4

4.3.2 Confirming Version of Intel RAID Option ROM Installed....................................4

4.3.3 Using the Intel RAID Option ROM.....................................................................4

4.4 Installing the Intel Application Accelerator RAID Edition ............................................10

4.4.1 Installation Caution..........................................................................................10

4.4.2 Steps to Take Before Installing the Intel Application Accelerator RAID Edition 10

4.4.3 Obtaining and Installing the Intel Application Accelerator RAID Edition...........10

4.5 Confirming the Intel Application Accelerator RAID Edition is Installed .......................14

4.6 Confirming Version of Intel Application Accelerator RAID Edition Installed................14

4.6.1 Using the Intel Application Accelerator RAID Edition Utility:............................15

4.6.2 RAID Driver File Properties:.............................................................................15

4.7 Issues During Installation...........................................................................................15

4.7.1 Symptom: Incompatible Hardware...................................................................15

4.7.2 Symptom: Unable to launch Intel(R ) Application Accelerator Readme file......15

4.8 “RAID Ready”.............................................................................................................16

4.8.1 “RAID Ready” Definition ..................................................................................16

4.8.2 “RAID Ready” System Requirements ..............................................................16

4.8.3 Steps on Setting Up a “RAID Ready” System..................................................16

4.8.4 Converting a “RAID Ready” System into RAID 0 or RAID 1 System with

Migration Feature .....................................................................................................16

4.9 RAID Migration Instructions.......................................................................................17

4.9.1 Create RAID Volume from Existing Hard Drive................................................18

4.9.2 Migration Process May Take Considerable Time to Complete ........................21

4.10 Uninstalling the Intel Application Accelerator RAID Edition......................................22

4.10.1 Uninstall Warning...........................................................................................22

4.10.2 Windows* 2003 / Windows 2000...................................................................22

4.11 Unattended Installation Under Windows* 2003 / Windows 2000..............................23

Tomcat i7221A S5151

Table of Contents

iv

http://www.tyan.com

4.12 Intel Storage Utility...................................................................................................23

4.12.1 Description.....................................................................................................23

4.12.2 Create Volume Manually................................................................................23

4.12.3 Successful Creation.......................................................................................27

4.13 Configure BIOS for Adaptec RAID for Serial ATA on Board.....................................28

4.13.1 BIOS Configuration........................................................................................28

4.13.2 Installing Serial ATA (SATA) hard disks.........................................................28

4.13.3 Adaptec RAID Configuration Utility ................................................................28

4.13.4 Manage Array................................................................................................29

4.13.5 Create Array ..................................................................................................30

4.13. 6 Add/Delete Hotspare....................................................................................32

4.13.7 Initialize Drives...............................................................................................32

4.13.8 Disk Utilities ...................................................................................................33

Chapter 5: Diagnostics...........................................................................................................1

5.1 Beep Codes.................................................................................................................1

5.2 Flash Utility ..................................................................................................................1

Appendix I: Glossary..............................................................................................................1

Appendix II: Post Error Code for BIOS..................................................................................7

Technical Support.................................................................................................................12

Tomcat i7221A S5151 Before you begin…

v

http://www.tyan.com

Before you begin…

Check the package contents before you proceed.

The retail motherboard package should contain the following:

1 x Tomcat i7221A S5151 motherboard

1 x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

1 x Tomcat i7221A S5151User’s Manual

1 x Tomcat i7221A S5151 Quick Reference Guide

1 x TYAN driver CD

1 x Intel 82801FR (ICH6R) Driver Diskette

1 x Adaptec Driver Diskette

1 x I/O shield

2 x Serial ATA power cable

4 x Serial ATA cable

1 x USB2.0 cable

If any of these items are missing, please contact your vendor or dealer for replacement before

continuing with the installation process.

Tomcat i7221A S5151

Chapter 1: Introduction

1-1

http://www.tyan.com

Chapter 1: Introduction

1.1 Congratulations!

Congratulations on your purchase of the TYAN Tomcat i7221A S5151, one of the most

powerful and versatile motherboard solutions available for Intel Prescott and Tejas processors.

Based on the Intel E7221 MCH chipset, the S5151 offers exceptional performance and

outstanding features. With the x1 PCI Express slots, onboard two Gigabit Ethernet ports,

Serial ATA RAID, four Dual-channel DDR DIMM sockets and four optional SCSI ports, the

Tomcat i7221A S5151 is ideal to fit your server/workstation needs.

For more information about this and other TYAN products, visit the TYAN Web site at

http://www.tyan.com. Product FAQs, a list of distributors and advanced BIOS information are

also available on the Web site.

1.2 Hardware Specifications

Processors

Ÿ Single Socket-T (LGA775 socket)

Ÿ Intel



“Prescott” processor with EM64T

support

Ÿ 800/533MHz FSB support

Expansion Slots

Ÿ One PCI-X 64-bit 133/100/66MHz bus

supports with

? One PCI-X slot

? One proprietary 200-pin SO-DIMM

connector

Ÿ Two x1 PCI Express connectors

Ÿ One 32/33 PCI v2.3 slots

Chipset

Ÿ Intel E7221 GMCH

Ÿ Intel ICH6R South Bridge

Ÿ Intel PXH-V I/O bridge

Ÿ SMSC DME1737 Super I/O

System Management

Ÿ SMSC DME1737 w/ hardware monitoring

Ÿ One 3+1-pin CPU Fan header w/

tachometer input and temperature-sensing

auto fan control

Ÿ Four 3-pin system Fan headers (two w/

tachometer input and temperature-sensing

auto fan control)

Ÿ Temperature and voltage monitoring

Ÿ Watchdog timer

Ÿ Port 80 code display LED

Memory

Ÿ Dual memory channels

Ÿ Supports Up to 4 DDR-333/400 DIMM

Ÿ Up to 4GB unbuffered, ECC/Non-ECC

memory

Integrated I/O Interfaces

Ÿ One floppy connector

Ÿ Four USB 2.0 ports (via cable)

Ÿ One COM2 port (via cable)

Ÿ One LPT port (via cable)

Ÿ Power/IDE/SATA LED connectors

Ÿ Two 2+2-pin headers for front panel

LAN LED

Ÿ TYAN 2 x 9 front-panel pin headers

Integrated LAN Controllers

Ÿ Two GbE LAN controllers

? Two Broadcom BCM5721 PCI

Express GbE LAN controller

? Operating at x1 PCI-E interface

? ASF 2.0 support

Ÿ One 10/100 Ethernet LAN controller

? Intel 82551

Optional modules

Ÿ M7901, SO-DIMM Ultra 320 SCSI card

? Adaptec AIC-7901X single-channel

Ultra 320 SCSI controller

? Adaptec HostRAID support w/RAID

0, 1, 10 supported

Ÿ M7902, SO-DIMM Ultra 320 SCSI card

? Adaptec AIC-7902W dual-channel

Ultra 320 SCSI controller

? Adaptec HostRAID support w/RAID

0, 1, 10 supported

Ÿ M8110 SO-DIMM SATA card

? Adaptec AIC-8110 SATA I controller

? Support up to 4-port (M8110) SATA

port running at 1.5GB/s

? Adaptec HostRAID support with

RAID 0, 1, 10 supported

Tomcat i7221A S5151

Chapter 1: Introduction

1-2

http://www.tyan.com

Integrated PCI IDE (ICH6R)

Ÿ Single channel master mode supports two

IDE devices

Ÿ Support for ATA-100/66/33 IDE drives and

ATAPI compliant devices

Integrated Serial ATA (ICH6R)

Ÿ Four Serial ATA Host controllers embedded

Ÿ Support four Serial ports running at 1.5Gb/s

Ÿ RAID 0, 1 support

Integrated PCI Graphics

Ÿ 8-bit VGA DAC embedded the MCH to

support an analog display

Rear Panel I/O ports

Ÿ Stacked PS/2 Mouse & Keyboard ports

Ÿ One 15-pin VGA port

Ÿ One 9-pin COM port

Ÿ Two RJ45 10/100/1000 Base-T port w/

activity LED

Ÿ One RJ45 10/100 Base-T port w/activity

LED, 2x USB2.0 combo ports

BIOS

Ÿ Award BIOS 8Mbit Flash ROM

Ÿ Support APM 1.2 & ACPI 1.0

Ÿ PnP, DNI 2.0, WfM 2.0 Power

Management

Power

Ÿ EPS12V support, on board 4-phase

VRM

Ÿ Universal 24-pin + 8-pin power

connectors

Ÿ 4-pin auxiliary power connector

Form Factor

Ÿ ATX footprint

Ÿ 9.6” x 12.0” (243.8mm x 304.8mm)

Regulatory

Ÿ FCC Class B (Declaration of

Conformity)

Ÿ CE (Declaration of Conformity)

Ÿ BSMI

Note

TYAN reserves the right to add support or discontinue support for any OS

with or without notice.

Tomcat i7221A S5151 Chapter 2: Board Installation

2-1

http://www.tyan.com

Chapter 2: Board Installation

2.1 Installing the Motherboard

The Tomcat i7221A S5151 motherboard conforms fully to the ATX specification. Before

continuing with the installation, confirm that your chassis supports a standard ATX

motherboard. If you are unsure, contact your dealer for more information.

2.1.1 Installation Notes

This user manual contains important information and you should read it thoroughly before

attempting the installation procedure.

Precautions:

• Static electricity can damage components on your motherboard. Before touching the

product, discharge any static build up in yourself by touching a well grounded object

such as a metal water pipe or a grounded electrical appliance. TYAN recommends

putting on a good quality grounded wrist strap before removing your motherboard from

the antistatic bag.

• Disconnect your computer from the power supply before any disassembly procedure is

attempted.

• Touch the motherboard as little as possible and do not touch the bottom of the board at

• all. Bending or flexing the motherboard may break delicate components or copper tracks

on the board.

• Avoid touching any of the motherboard components.

• Place the motherboard on a grounded antistatic surface or on the antistatic bag in which

the board was shipped.

• Inspect the board for damage.

Read the following sections for detailed instructions on how to install your motherboard in a

chassis and add a processor, memory, and disk drives.

Warning

Do not apply power to the board if it appears damaged.

Tomcat i7221A S5151 Chapter 2: Board Installation

2-2

http://www.tyan.com

2.2 Board Image

The following is an image of the Tomcat i7221A S5151.

The above photograph is purely representative. Due to engineering updates and new

board revisions, certain components may change and or be repositioned. The picture

above may or may not look exactly like the board you received.

Tomcat i7221A S5151 Chapter 2: Board Installation

2-3

http://www.tyan.com

2.3 Block Diagram

The following is a block diagram of the Tomcat i7221A S5151.

Tomcat i7221A S5151 Chapter 2: Board Installation

2-4

http://www.tyan.com

2.4 Motherboard Components

The diagram below shows the main motherboard components.

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64-bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P

JP24

JP26

FDD

LPT

JP4/JP5/JP6/JP7

JP2

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

JP9

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

E7221

Broadcom

5721

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP8

Broadcom

5721

1

1 1

This diagram represents the latest version of the motherboard available at the time of

publishing. The board you receive may or may not look exactly like the above diagram.

Parts are not drawn to scale.

Tomcat i7221A S5151 Chapter 2: Board Installation

2-5

http://www.tyan.com

2.5 Jumpers and Connectors

Jumpers and pin headers are provided on your motherboard for configuration and connection

to peripherals. The following section shows you how to set your jumpers and use your pin

headers.

Connector Function Ref. Page

J5 COM2 port Page 2-6

J12 SO-DIMM socket Page 2-6

J20/J21/J22/J23 Serial ATA RAID connectors Page 2-7

JP1/JP2/JP3 LAN2/LAN1/LAN3 disabled headers Page 2-7

JP4/JP7 Front Panel LAN1/LAN2 Speed LED pin-headers Page 2-8

JP5/JP6

Front Panel LAN1/LAN2 Link and Active LED

connectors

Page 2-8

JP8 Chassis Fan connector Page 2-9

JP20 SMDC connector Page 2-12

JP12/JP13 Front panel USB2.0 connectors Page 2-10

JP14 PCI-X speed select header Page 2-12

JP15 Clear CMOS jumper Page 2-11

JP17/JP18/JP23 Front fan connectors Page 2-9

JP24/JP25 SMDC/ASF2.0 select headers Page 2-13

* Some jumpers and headers are optional and not available with the board due to the different

configurations.

Jumper Legend

Jumper OFF – open (without jumper cap)

Jumper ON – closed (with jumper cap)

Tomcat i7221A S5151 Chapter 2: Board Installation

2-6

http://www.tyan.com

2.5.1 Com Port: J5

10 2

9 1

Signal Description

GND

(Ground)

DTR

(Data-Terminal-Ready)

TX

(Transfer-Data)

RX

(Receive-Data)

DCD

(Data Carrier Detect)

Pin#

9 7 6 3

1

Pin#

10 8 5 4

2

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Signal Description

NC/Key

RI

(Ring-Indicator)

CTS

(Clear-to-Send)

RTS

(Request-to- Send)

DSR

(Data-Set-Ready)

2.5.2 SO-DIMM Socket: J12

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Connect SCSI Daughter Card

Compatible with Tyan Taro M7902 or

M7901

Also connect SO-DIMM SATA card

Compatible with Tyan Taro M8110

http://www.tyan.com/products/html/access

ory.html

J5

J12

Tomcat i7221A S5151 Chapter 2: Board Installation

2-7

http://www.tyan.com

2.5.3 Serial ATA RAID Connectors: J20/J21/J22/J23 (SATA1 / SATA2 / SATA3 / SATA4)

7 GND

6 RXP

5 RXN

4 GND

3 TXN

2 TXP

7

1

1 GND

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Connects to the Serial ATA ready drives

via the Serial ATA cable

You may use any two of the four Serial

ATA ports to have the support of RAID 0

and 1 through the on board ICH6R south

bridge chip.

2.5.4 LAN1/LAN2/LAN3 Disabled Headers: JP2/JP1/JP3

1

JP1/JP2

OPEN: Disabled

CLOSED: Enabled (Default)

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

1

3

1

JP3

Pin 1-2 Closed:

Enable

(Default)

Pin 2-3 Closed: Disable

SATA

JP3

JP1

JP2

Tomcat i7221A S5151 Chapter 2: Board Installation

2-8

http://www.tyan.com

2.5.5 Front Panel LAN1/LAN2 Link and Active LED Connectors: JP5/JP6

JP5 (for LAN1)

1

Pin 1: LED+

Pin 2: LED-

JP6 (for LAN2)

1

Pin 1: LED+

Pin 2: LED-

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Use these headers to connect with the

front panel link/activity LEDs for LAN1 and

LAN2.

2.5.6 Front Panel LAN1/LAN2 Speed LED Pin-Headers: JP4/JP7

1

Pin 1: Green+

Pin 1: Orange+

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Use these headers to connect with the

front panel dual color LEDs to indicate the

speed of LAN1 and LAN2.

Off = 10 LAN

Green = 100 LAN

Orange = GbE LAN

Reference section 2.11.1 for the correct

LAN LED color definition.

JP4 for LAN1, JP7 for LAN2

JP5/JP6

JP4/JP7

Tomcat i7221A S5151 Chapter 2: Board Installation

2-9

http://www.tyan.com

2.5.7 Front Fan Connectors: JP17/JP18/JP23

+12V

GND

NC

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP8

J5

Use these headers to connect the chassis

cooling fans to your motherboard to keep

the system stable and reliable.

JP17 and JP23 support the tachometer

monitoring and auto fan speed control.

2.5.8 Chassis Fan Connector: JP8

+12V

GND

NC

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP8

J5

Use this header to connect the chassis

cooling fan to your motherboard to keep

the system at optimum performance

levels.

These connectors support the tachometer

monitoring and auto fan speed control.

JP8

JP23

JP17

JP18

Tomcat i7221A S5151 Chapter 2: Board Installation

2-10

http://www.tyan.com

2.5.9 CPU Fan Connector: JP22

+12V

V3P3

Speed Control

Tachometer

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Use this header to connect the processor

cooling fan to your motherboard to keep

the system stable and reliable.

This connector supports the tachometer

monitoring and auto fan speed control.

2.5.10 Front Panel USB 2.0 Connectors: JP12/JP13

10 2

9 1

NC

GND

Data 1+

Data 1 -

+5V

9 7 5 3 1

10 8 6 4 2

GND

Data 2+

Data 2 -

+5V

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Use these headers to Connect to the USB

devices via the enclosed USB cable.

JP22

JP13

JP12

Tomcat i7221A S5151 Chapter 2: Board Installation

2-11

http://www.tyan.com

2.5.11 Clear CMOS Jumper: JP15

3

1

Default

3

1

Clear

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

Use this jumper when you forgot your

system/setup password or need to clear

system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect

power supply from AC source

- Use jumper cap to close Pin_2 and 3

for several seconds to Clear CMOS

- Replace jumper cap to close Pin_1

and 2 (default setting)

- Reconnect power supply to AC

source

Power on system

2.5.12 Front Panel System Connector: JP16

1 2

17 18

Function PIN PIN Function

HD_LED+

1 2

PLED+

HD_LED-

3 4

PLED-

GND

5 6

Power Button

Reset

Button

7 8

GND

EXINT +5V

9 10

NC

EXINT

11 12

GND

+5VSB

13 14

NC

SMBUS

Data

15 16

GND

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

SMBUS

Clock

17 18

INTRU

JP15

JP16

Tomcat i7221A S5151 Chapter 2: Board Installation

2-12

http://www.tyan.com

2.5.13 SMDC Connector: JP20

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

For connection with Tyan Server

Management Daughter Card (SMDC)

*Optional on some versions of the S5151

motherboard.

2.5.14 PCI-X Speed Select Header: JP14

1

3

Pin 1-2 Closed: 133MHz

(Default)

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

3

1

Pin 2-3 Closed: 100MHz

JP20

JP14

Tomcat i7221A S5151 Chapter 2: Board Installation

2-13

http://www.tyan.com

2.5.15 SMDC/ASF2.0 Select Headers:JP24/JP25

3

1

Support ASF 2.0

DIMM 2

DIMM 1

DIMM 4

DIMM 3

64bit 133/100/66MHz PCI-X

X1 PCI Express

32-bit 33MHz (5V) PCI

IDE J17

X1 PCI Express

SO-DIMM

J25P JP24

FDD

LPT

JP4/JP5/JP6/JP7

JP2

BROADCOM

5721

BROADCOM

5721

SMSC

I/O

JP1

LAN

82551

JP13

JP12

INTEL

ICH6R

JP15

SATA1

SATA3

J19

SATA4

SATA2

SMDC

JP16

JP18

JP17

BIOS

JP23

JP22

INTEL

PXH-V

INTEL

PXH-V

INTEL

E7221

BROADCOM

5721

JP3

LAN

VGA

JP3

COM

PORT

USBX2

LAN

PS/2

JP14

JP18

J5

3

1

Support SMDC card

JP25

JP24

Page is loading ...

Tyan S5151 User manual

This manual is also suitable for

Tyan S5151 User manual

Related papers

Other documents