Atdec VF-WD Specification

VF-WD
Atdec
Brand
Atdec
Model
VF-WD
Category
Flat panel wall mounts
Type
Specification

Atdec VF-WD is a wall mount for flat-panel monitors, supporting up to 17.5lbs. It's designed for noninteractive environments, making it ideal for offices, classrooms, and public spaces. The mount allows for easy adjustment of the display's viewing angle, both in landscape and portrait orientations. It also includes a tilt mechanism for fine-tuning the display's position. Installation is simple, with all necessary hardware included.

Atdec VF-WD is a wall mount for flat-panel monitors, supporting up to 17.5lbs. It's designed for noninteractive environments, making it ideal for offices, classrooms, and public spaces. The mount allows for easy adjustment of the display's viewing angle, both in landscape and portrait orientations. It also includes a tilt mechanism for fine-tuning the display's position. Installation is simple, with all necessary hardware included.

Component Checklist
Component Checklist
Component Checklist
Component Checklist
Disassemble
Step 1
Using the supplied
Allen Key, remove
the bottom screw.
Installation Instructions
IMPORTANT: Ensure you have received all parts
against the component checklist prior to installing.
Bits Bag
5mm Allen Key
Wall Plug (x2)
50mm Screw (x2)
Mounting Fasteners
M4x10mm Screw (x4)
M4x12mm Screw (x4)
M4x16mm Screw (x4)
Visidec Focus Wall Direct
supports a maximum
weight of 8kgs (17.5lbs)
TOOLS REQUIRED:
l Power Drill
l 5.5mm (1/4”) Drill Bit
l 8mm (5/16”) Drill Bit
l Phillips Head Screwdriver
NOTE: This product is
designed to support
a flat panel monitor
in a noninteractive
environment.
i.e. It should not be
used in a situation
where the display’s
position will be
frequently changed.
A
Step 2
Separate the two
components.
Wall Direct Assembly
Attach Base to Wall
Masonry Wall
B
Timber Stud Wall
OR
Wall Plug
8mm (5/16”) hole
50mm Screw
Tip: Use a Spirit Level
to ensure this surface
is horizontal.
5.5mm (1/4”) hole
Timber
Stud
50mm Screw
Tip: Use a Spirit Level
to ensure this surface
is horizontal.
Attach Head to Display
D
Attach Display to Wall
E
Adjust Display Position
F
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.01.08 ©
OR
Step 1
Position the
Display & Bracket
over the Base.
Step 2
Close the two halves of the Bracket
around the Base by firstly positioning
the top half and then the bottom half.
Step 3
Reassemble the Wall Direct Assembly
ensuring the weight of the display is
supported until the screw is tightened.
Tip: This step can be made
easier by using two people.
WARNING:
Do not
overtighten.
Step 1
Adjust the display to
the desired viewing
angle then lock it in
place by tightening
the tilt screw in the
direction shown.
Step 2
Adjust the display’s
position between
landscape and portrait.
The display can rotate
through +/-95º.
WARNING:
Do not
overtighten.
NOTE:
Screen does not
rotate 360°
Tighten
+/-95º
1
2
75x75mm VESA 100x100mm VESA
75mm
(3”)
75mm
(3”)
M4 screw
M4 screw
100mm
(4”)
100mm
(4”)
  • Page 1 1
  • Page 2 2

Atdec VF-WD Specification

VF-WD
Atdec
Brand
Atdec
Model
VF-WD
Category
Flat panel wall mounts
Type
Specification

Atdec VF-WD is a wall mount for flat-panel monitors, supporting up to 17.5lbs. It's designed for noninteractive environments, making it ideal for offices, classrooms, and public spaces. The mount allows for easy adjustment of the display's viewing angle, both in landscape and portrait orientations. It also includes a tilt mechanism for fine-tuning the display's position. Installation is simple, with all necessary hardware included.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents