Atdec SD-WD Installation guide

Brand: Atdec

Model: SD-WD

Type: Installation guide

Atdec SD-WD is a wall mount designed for displays with VESA patterns of 75x75mm and 100x100mm. It can support up to 25kg (55lbs) and allows for 20° of angular movement. It comes with a variety of screws for attaching the VESA plate to the display and M6 coach screws with nylon anchors for mounting the bracket to a timber stud or masonry wall. An optional security screw is also included to prevent unauthorized removal of the display.

Component Checklist

Step 1. Component Checklist

Check you have received all parts against the Component Checklist above.

Installation Instructions

Wall Mount

Assembly (x1)

Step 2. Installing the Wall Mount Assembly (choose from one of the following options)

For mounting Spacedec to a Timber Stud Wall - Using the Wall Mount Assembly Bracket, mark

the location of the 4 holes and drill using a 4mm drill bit. Secure the bracket to the wall using the M6 Coach

Screws as shown in diagram A.

For mounting Spacedec to a Masonry Wall - Using the Wall Mount Assembly Bracket, mark

the location of the 4 holes and drill using an 8mm masonry drill bit. Secure the bracket to the wall using the M6

Coach Screws and Nylon Anchors as shown in diagram B.

A. Timber Stud Wall

B. Masonry Wall

Note: This product will suit VESA compliant monitors with 75mm x 75mm (3” x 3”) and 100mm x 100mm (4” x 4”) hole patterns only.

It will support up to a maximum weight of 25kg (55lbs).

Display | Wall Direct

SD-WD

VESA

plate (x1)

Hardware

Mounting Fasteners

M4x10mm

Screw (x4)

M4x12mm

Screw (x4)

M4x16mm

Screw (x4)

(Optional)

Security

Screw (x1)

M6 Coach

Screws (x4)

Nylon

Anchor (x4)

Combined 3mm

Allen Key and

Phillips-head

Screwdriver (x1)

Wall Mount Assembly

Bracket

M6 Coach

Screw

4 x 4mm

Holes

Wall Material

Stud



TOOLS REQUIRED:

• Power Drill

• Phillips-head Screwdriver

• 4mm (

”) Drill Bit

• 8mm (

”) Masonry Drill Bit

• 8mm (

”) Socket Wrench

or Shifter

Wall Mount Assembly

Bracket

M6 Coach Screw

4 x 8mm

Holes

Masonry Wall

Nylon Anchor

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 23.11.11 ©

Installation Complete

There are two mounting hole configurations:

• 75 x 75mm

• 100 x 100mm

Choose appropriate Mounting Screws

from the Hardware supplied to suit

your Display.

Top of

Display

Mounting Screws (x4)

VESA Plate

Back of Display

75mm

(3”)

100mm

(4”)

75mm

(3”)

100mm

(4”)

Step 4. Attach your Display to the Wall Mount Assembly

Step 5.

Adjust the VESA Ball Mount

Step 3. Attach the VESA plate to your Display

Position your Display to the desired viewing angle, using the 20°

angular movement allowed by the VESA Ball Mount.

Depending on the weight of the display, it may be necessary to make

adjustments to the VESA Ball Mount. If the display does not hold its

position, or is too resistant, adjust the Tension Plate located at the

rear of the VESA Ball Mount (see diagram right).

To make any adjustments tension evenly using the 3mm Allen Key

supplied. Apply half a turn at a time to each screw on the Tension

Plate to adjust evenly.

Check the display, and then adjust again if necessary.

Loosen (-Kg)

Tension

Plate

Tighten

(+Kg)

Combined Phillips-head

Screwdriver/Allen Key

supplied

(Optional) Insert the Security Screw

supplied and tighten using a

Phillips-head Screwdriver.

Press and hold the Release Buttons.

Gently insert bottom of VESA Plate

into Quickshift Mount. Release

Buttons to lock

in place.

Security

Screw

Hook the top of the VESA Plate onto

the VESA Ball Mount.

Back of Display

Combined Phillips-head

Screwdriver/Allen Key

supplied

Atdec SD-WD Installation guide

Atdec SD-WD Installation guide

Atdec SD-WD Installation guide

Related papers

Other documents