Australian Owned, Designed and Manufactured
Genesis Electronics Australia Pty Ltd
www.genesiselectronics.com.au
info@genesiselectronics.com.au
Genesis reserves the right to change or modify products without notice.
This manual assumes installers of this product are professionals within
the electronic security, access control and automation industry. As such,
knowledge of these industries on the part of the installer is assumed.
Genesis takes no responsibility for any damage, financial loss or injury
caused to any equipment, property or persons resulting from the correct
or incorrect use of any Genesis devices.
Distributed By:-
MODEM INSTALL MANUAL
GEN-127
TECHNICAL MANUAL
…The very latest innovation in security and access
genesis
Version 4, May 2006
© Genesis Electronics Australia Pty Ltd
www.genesiselectronics.com.au
Page 2 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Table of Contents
TABLE OF CONTENTS 2
PARTS CHECKLIST 3
SPECIFICATIONS 3
FEATURES AND BENEFITS 4
MODEM LAYOUT 5
MODEM TERMINAL LAYOUT 5
MODEM TERMINAL DESCRIPTIONS 9
MOUNTING 6
CONNECTED TO YOUR PC 6
SETTINGS FOR THE EXTERNAL MODEM 6
CONNECTING TO THE PANEL VIA THE MODEM 7
CONNECTING TO ALADDIN VIA THE MODEM 7
POINTS TO NOTE 8
Page 11 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
NOTES
Page 10 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
NOTES
Page 3 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Parts Checklist:
1 x Netcomm PCB Modem (GEN-127)
□
1 x PCB Power supply board
□
1 x Genesis Connection Lead (GEN-150)
□
1 x Serial RS-232 Connection Lead ( GEN-155)
□
1 x Power Lead
□
1 x Netcomm PCB – Technical Manual (this manual)
□
□
Dimensions
H 76mm x W66mm x D32mm
Input Voltage
12v DC
Standby Current Draw
50mA
V.92 Up Stream rate
Up to 48Kbps, Quick Connect and Modem-on-hold
functions
Formats Supported
Bell 212A and Bell 103
Phone Line connection
2 wire PSTN
Upgrades
Flash upgradeable
Class
Fax Class 1 & 2
Features
Caller ID, Extensive AT Commands
Specifications:
Page 4 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Features & Benefits:
The GEN127 is small in design that can easily be fitted in the same cabinet
with the Master Panel. the GEN127 modem is ideal when high speed re-
mote access is required. For instance if your site is far from your office
and inconvenient to travel to the site, it is ideal for either access control
site maintenance or programming function changes.
GEN127 Modem provides communication at the same speed as the direct
connect cable to the panels RS232 port communication port at 9600 baud
rate. The modem provides all programming from the comfort of your of-
fice in front of your personal computer as if you were on site.
Unlike conventional modems, GEN127 doesn’t require additional 12v DC
power supply. The modem can simply be connected Direct to the Genesis
Panel auxiliary 12v DC power output terminals.
Page 9 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
NOTES
Page 8 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Points to Note:
If the Modem fails to communicate with the panel even after the modem at the panel has
answered then the time out setting is too short. To increase the time refer to program-
ming option 2.
Ensure the screen saver and power options on you PC have not been enabled. There may
be certain conflicts between upload and downloads.
Ensure the panel number is correct in the Set System Defaults. Using the correct database
is always advised.
If you are still having a problem connecting to the panel via the modem, try starting a
new database. Run the Auto Program with the correct information and upload the data
from the panel.
It is always good practice when connecting the Genesis via modem to check the COM
Port settings and ensure that the default is set to COM Port 2.
The Modem type that is recommended for remote communication to the Genesis system
is a Netcomm Roadster Modem V.92 (pictured below), this Modem has been tested to
operate correctly and is best suited to the Netcomm GE-1000 Modem on the panel side.
NETCOMM ROADSTER
MODEM V.92
Page 5 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
OC Module Layout:
RJ-11 PSTN line
input jack
DB-9 RS-323
Serial Lead input
Plug-in 12v DC
input is center +
Plug-on modem
module to the
power supply
Power supply
PCB base for
modem board
Modem Phone Line
Input:
The modem phone line input is for direct connection to a
phone line socket. This enables the modem to send and re-
ceive information for the Genesis Panel Version 2.
DC Input:
The DC Input must be connected to the Genesis Version 2
panel located at the 12v DC terminals, rather than getting its
power from an external source. This is required so that the
Modem Strings synchronise with the Genesis panel.
DB9 Connector:
The DB9 Connector is a terminal, which connects directly to
the PC RS232 Port on the Genesis Panel. This port is for
transferring information from the Genesis through to the Mo-
dem.
Modem Terminal Descriptions:
Page 6 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Modem mounting:
When mounting the Modem, it is important to note the following;
Optional mounting plate can be purchased
Ensure the terminals do not make contact with any part of the Genesis Metal Cabinet
(GEN-130)
Avoid installing the Modem where it may be exposed to moisture, either directly (Rain,
Sprinklers, Hoses), or by condensation.
Settings for the Modem connected to your PC:
The Genesis Upload / Download software has been configured for use with NETCOMM
external Modem for connection to the Genesis Panel. To set the PC Modem type for the
Genesis:
Go to the Technician tab on the Technician Software Version 3.2j or higher.
From there you must scroll down to the Program.
Then select the Dialler, Modem, STU.
From this point select the Program Ext Modem.
From here you must select the option labelled NETCOMM.
Settings for the External Modem to the Genesis Panel:
Genesis Technician Software V3.2j – Program the Modem connected to your PC by
entering the Genesis Technicians software:
Go to the Equipment Menu
Then scroll to Set System Defaults.
Change the TIMEOUT to 60 Seconds.
Program INIT 1 as AT & F & D0 & K0E0S95=1
Program the phone number the Genesis Modem is connected to. Always program an ATD
before the number, ensure area code is entered as well.
Eg. Phone number (03) 9596 6688 ATD0395966688
Page 7 Version 4 – May 2006
genesis IG-1000 Modem - Technical Manual
Initialising the Netcomm IG-1000 Modem:
The Netcomm Modem now has to talk to the Genesis Panel:
Once the download is complete close the Technician Software. Remove the PC Link
Cable and insert the Modem DB9 connection cable to the PC Link RJ45 Connection
point.
Power up the Modem via 12v DC auxiliary output from the Genesis Panel.
Press and hold the RESET button on the master Panel for 1 second and release. The
system will reset and the LED’s on the Modem will flicker indicating that the initializa-
tion string has been sent to the modem.
Windows setup for Modem – The settings for the modem within the windows setup
needs to be configured. Modem settings to be set:
Go to the Modem Properties in the computer.
Then go to the advanced settings. Here you will an open box for initialisation string.
Now set the extra string to AT&F&D0&K0E0S95=1.
Connecting to the Panel via the Modem:
Open the Technician Software and check that the COM Port in the Set System De-
faults is set to the same port as your modem. Go Connect/Via Modem. The Genesis
modem will be called and a link established, the Comm.'s light will change from RED
to GREEN.
Now all functions normally carried out via the PC Link can be carried out via the Mo-
dem.
Connecting to Aladdin via the Modem:
Open the Technician software and check that the COM Port in the Set System De-
faults is set tot he same port as your modem.
Also ensure that the Modem Connection Used in Aladdin is selected.
Save and exit out of the Technician software and start up Aladdin using the same data-
base as in the Technician Software.
Log into Aladdin and then select the CONNECT Icon
Installation:
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Genesis Integrated Security System User manual
-
-
-
-
Genesis G90 Owner's manual
-
-
-
-
-
Other documents
-
Netcomm II 128 USB User manual
-
Campbell Scientific PS150 Owner's manual
-
Zebra PTC-2124 Owner's manual
-
-
-
Bristol Babcock Bristol Network 3000 Communications Configuration Guide
-
-
Aaeon GENESYS-WHU6 User manual
-
AMT Datasouth Codewriter 4500 Series User manual
-
Lexmark GENESIS S815 Features & Benefits
