Atdec TH-PS-D Installation guide

Atdec
Brand
Atdec
Model
TH-PS-D
Category
Projector mounts
Type
Installation guide

Atdec TH-PS-D is a sturdy and versatile short throw projector wall mount, capable of supporting up to 55 lbs. of weight. It easily attaches to either timber studs or masonry walls and comes with all necessary hardware for a secure installation. The mount's flexible design allows for +/-5° of adjustment to accommodate wall slopes or specific projector needs. It also features a cable cover to keep cords organized and protected, and an end cap to ensure a clean and finished look.

Atdec TH-PS-D is a sturdy and versatile short throw projector wall mount, capable of supporting up to 55 lbs. of weight. It easily attaches to either timber studs or masonry walls and comes with all necessary hardware for a secure installation. The mount's flexible design allows for +/-5° of adjustment to accommodate wall slopes or specific projector needs. It also features a cable cover to keep cords organized and protected, and an end cap to ensure a clean and finished look.

Step 2. Position Central Connector
Select the position of the Central
Connector before mounting the
Wall Plate to the wall.
TH-PS-D
Component Checklist
Short Throw Projector Wall Mount | Dual Stud
Support Arm
! IMPORTANT - Install Short Throw Projector Mount as per installation instruction.
! This product supports a maximum load of 25kg (55lbs.).
! The manufacturer accepts no responsibility for incorrect installation.
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received against the component checklist and hardware above.
Wall Plate
End Covers
Extrusions
HARDWARE
Coach Screw
(x6)
Nylon
Anchor (x6)
Washer (x6)
3mm Security
Allen Key
Security Screw (x2)
Tools Required:
• Power Drill
• 6mm(0.23”) Drill Bit
• 12mm(0.47”) Masonry Drill Bit
• 13mm (0.5”) Socket Wrench Shifter
• Phillips Head Screwdriver
Step 3. Mounting Wall Plate
Masonary Timber Stud
Coach Screw
Coach Screw
Washer
Washer
Ø12mm x 65mm deep
Drilled Hole
Ø6mm x 65mm deep
Drilled Hole
Nylon Anchor
IMPORTANT! Any structural elements must be capable of supporting the combined weight of
all the equipment and devices being mounted. If in doubt, consult a structural engineer.
TIP: Use Mount as a drilling template.
Installation Instructions
Slide the hook on the Support
Arm over the top bolts on the
Wall Plate.
Swing the Support Arm down so
the bottom slots slide over the
bottom bolts.
The Support Arm can be
adjusted by +/- 5° to account
for wall slope or individual
projector characteristics.
Adjust the stop bolt as
shown to maintain the
desired angle.
Secure the position of the Support
Arm by tightening the two bolts on
each side of the Wall Plate.
LH
5.1. Remove screw from End Cap and slide End Cap off
5.2. Loosen screws on Sliding Pole Mount and slide the entire assembly off
5.3. Slide off Base Cover
5.4. Slide the Cable Cover out
Step 4. Insert Covers and Extrusion onto Wall Plate
Step 5. Remove End Cap, Sliding Pole Mount, Base Cover and Cable Cover from Support Arm
Step 6. Attach Support Arm to Wall Mount
RH
Cable Cover Base Cover Sliding Pole Mount End Cap
+5°
-5°
6.1.
6.3.
6.4.
6.5.
6.2.
Extrusion
Cover
Installation Instructions
Break the Base Cover tab on the side to
allow the cable to exit through slot.
Secure the Base Cover with the
corresponding Security Screws.
Insert cable through Cable Cover and
slide onto the Support Arm.
Step 7. Re-Attach Covers and Cable Cover
Step 8. Attach Projector Mount
Option A
Option B
Ensure there is enough cable length
on either end.
Re-mount the Sliding Pole Mount with the cable fitted either in Option A or B.
This will depend on the projector, projector mount and position of the cable socket.
Reinsert the End Cap and secure with
the corresponding screw.
TH-PF
Projector Mount
The Cable Cover may need to be cut to length depending on where the projector is positioned along the Support Arm.
After the appropriate length has been attained, slide cover back on. Please refer to your projector documentation for
guidance on Focal Length/Throw.
7.1.
7.3.
7.4.
7.5.
7.2.
To complete installation please jump to Step 5 of TH-PF installation manual.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. P
ublished 10.04.13 ©
  • Page 1 1
  • Page 2 2
  • Page 3 3

Atdec TH-PS-D Installation guide

Atdec
Brand
Atdec
Model
TH-PS-D
Category
Projector mounts
Type
Installation guide

Atdec TH-PS-D is a sturdy and versatile short throw projector wall mount, capable of supporting up to 55 lbs. of weight. It easily attaches to either timber studs or masonry walls and comes with all necessary hardware for a secure installation. The mount's flexible design allows for +/-5° of adjustment to accommodate wall slopes or specific projector needs. It also features a cable cover to keep cords organized and protected, and an end cap to ensure a clean and finished look.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents