Minka Group N6686-874 User manual

Minka Group
Brand
Minka Group
Model
N6686-874
Type
User manual
INSTALLATION INSTRUCTIONS
Item #N6686-874 (11/30/2022)
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A KE R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING THE FIXTURE (Fig.2)
1. Carefully unpack the new fixture and lay out all the parts
on a clear area. Take care not to lose any parts necessary
for installation.
2. Shut off power at fuse box or circuit breaker. If necessary,
remove old fixture, including mounting hardware.
3. Pass fixture wires through all thread (A). Thread all thread
into coupling and secure with nut.
4. Place tube (B) and cap (C) over all thread.
5. By measuring determine desired hanging height and
thread rods (D & E) into top of all thread of fixture body.
6. Carefully pass fixture wires through each rod as you
assemble.
7. Pass wires through canopy (F) and pull until tight. Then
thread canopy onto top of rods.
MOUNTING THE FIXTURE (Fig.1)
8. The mounting strap contains several pairs of threaded
holes, find the pair of holes that match holes spacing in
your fixture canopy and thread two fixture screws into
mounting strap and tighten with hex nut. Note: The length
of fixture screw into mounting strap may be adjusted if
necessary.
9. Attach mounting strap to outlet box (not included) using
box screws (Size: #8-32*0.5L). The side of mounting strap
marked “GND” must face out.
10. The support cable is provided to support the weight of
fixture while wiring. Align fixture to mounting strap and
attach hook on the end of support cable into a slot located
on mounting strap. Carefully allow support cable to
support the weight of fixture while wiring.
CONNECTING THE WIRES (Fig. 3)
11. At this point, connect the electrical wires as shown in
Fig. 3, making sure that all wire connectors are secured. If
your outlet box has a ground wire (green or bare copper),
connect fixture’s ground wire to it. Otherwise, connect
fixture’s ground wire directly to mounting strap using green
screw provided.
12. Tuck wire connectors neatly into outlet box.
FINISHING THE INSTALLATION (Fig.1 & 2)
13. Place canopy (F) over two fixture screws (or all thread)
and secure with decorative nuts.
14. Install glass (I) to arm and secure with nut (J) and plastic
washers (H) provided. (Recommendation: Install glass
from bottom to top.)
15. Install final cap (G) onto bottom of body.
16. Install (6) six candelabra base bulbs up to 60 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification—DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased. Do not clean your light fixture or
parts with water or cleanser.
Fig.1
Fig.2
Fig.3
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set A-020
-Mounting strap
-Ground screw
-Mounting screws (2)
B
Outlet Box
Supply
Ground Wire
Fixture
Ground Wire
Box Screw
Canopy
Ground Scre
w
Decorative
Nut
Fixture
Screw
Mounting Strap
Hook
Supply
Wire
A
(36PCS)
C
E
D
F
G
J
H
Rod#
W35-1-874 *3
W35-H-874 *1
Glass#
GL6686
  • Page 1 1

Minka Group N6686-874 User manual

Minka Group
Brand
Minka Group
Model
N6686-874
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents