Metropolitan N7136-597 is a versatile lighting fixture that can be installed as a pendant or semi-flush mount. With its adjustable hanging height and supporting cable, you can customize the fixture to suit your space and lighting needs. The fixture's durable construction and easy installation make it a great choice for both residential and commercial applications.
Metropolitan N7136-597 is a versatile lighting fixture that can be installed as a pendant or semi-flush mount. With its adjustable hanging height and supporting cable, you can customize the fixture to suit your space and lighting needs. The fixture's durable construction and easy installation make it a great choice for both residential and commercial applications.
INSTALLATION INSTRUCTIONS
Item #N7135-597/N7136-597 For Pendant (03/27/2017)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig.1
Fig.2
Fig.3
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the mounting
hardware.
2. Carefully unpack the new fixture and lay out all the parts
on a clear area. Take care not to lose any parts necessary
for installation.
3. The mounting strap contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture canopy and thread the two fixture screws 1/4
into the fixture mounting strap.
4. Attach mounting strap to the outlet box using the box
screws (Size: #8-32*0.5L). The side of the mounting strap
marked “GND” must face out.
PREPARING THE FIXTURE (Fig.2)
5. By measuring, determine the desired hanging height and
thread rods (B) into the top nipple of the fixture body.
Please remove the nipple if installing with one 6" rod only.
6. Carefully pass the fixture wires through each rod as you
assemble.
7. Pass the wires through the swivel and canopy (C) and pull
tight. Then thread the swivel onto the top of rods.
8. Place supporting cable through lock and secure with
screw, Place the supporting cable through mounting strap
and lock and secure with screw.
CONNECTING THE WIRES (Fig. 3)
9. At this point, connect the electrical wires as shown in Fig.
3, making sure that all wire connectors are secured. If your
outlet box has a ground wire (green or bare copper),
connect the fixture’s ground wire to it. Otherwise, connect
the fixture’s ground wire directly to the mounting strap
using the green screw provided. After the wires are
connected, tuck them carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig.1 & 2)
9. Place fixture canopy (C) over two fixture screws (or
nipple) and secure with decorative nuts.
10. Place candle tube (A) on the socket.
11. Install the bulb in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!) NOTE: BULBS
WILL BE HOT!! ALLOW 10 MINUTES FOR BULBS TO
COOL BEFORE HANDLING.
Your installation is now complete. Return power to the outlet
box and test the fixture.
Note: Illustration on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased. Do not clean your light fixture or
parts with water or cleanser.
FIXTURE
WIRES
Black or
Smooth
H
O
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
O
USE
WIRES
Green
(Ground)
Set A-012
-Mounting plate
-Ground screw
-Mounting screws (2)
A
B
C
Outlet Box
Mounting Strap
Supporting Cable
Lock
Screw
INSTALLATION INSTRUCTIONS
Item #N7135-597/N7136-597 For Semi-Flush (03/27/2017)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig.1
Fig.2
Fig.3
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the mounting
hardware.
2. Carefully unpack the new fixture and lay out all the parts
on a clear area. Take care not to lose any parts necessary
for installation.
3. The mounting strap contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture canopy and thread the two fixture screws 1/4
into the fixture mounting strap.
4. Attach mounting strap to the outlet box using the box
screws (Size: #8-32*0.5L). The side of the mounting strap
marked “GND” must face out.
PREPARING THE FIXTURE (Fig.2)
5. Thread rods (B) into the top nipple of the fixture body.
6. Carefully pass the fixture wires through rod as you
assemble.
7. Pass the wires through the swivel and canopy (C) and pull
tight. Then thread the swivel onto the top of rods.
8. Place supporting cable through lock and secure with
screw, Place the supporting cable through mounting strap
and lock and secure with screw.
CONNECTING THE WIRES (Fig. 3)
9. At this point, connect the electrical wires as shown in Fig.
3, making sure that all wire connectors are secured. If your
outlet box has a ground wire (green or bare copper),
connect the fixture’s ground wire to it. Otherwise, connect
the fixture’s ground wire directly to the mounting strap
using the green screw provided. After the wires are
connected, tuck them carefully inside the outlet box.
FINISHING THE INSTALLATION (Fig.1 & 2)
9. Place fixture canopy (C) over two fixture screws (or
nipple) and secure with decorative nuts.
10. Place candle tube (A) on the socket.
11. Install the bulb in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!) NOTE: BULBS
WILL BE HOT!! ALLOW 10 MINUTES FOR BULBS TO
COOL BEFORE HANDLING.
Your installation is now complete. Return power to the outlet
box and test the fixture.
Note: Illustration on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased. Do not clean your light fixture or
parts with water or cleanser.
FIXTURE
WIRES
Black or
Smooth
H
O
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
O
USE
WIRES
Green
(Ground)
Set A-012
-Mounting plate
-Ground screw
-Mounting screws (2)
A
B
C
Outlet Box
Mounting Strap
Supporting Cable
Lock
Screw
-
1
-
2
Metropolitan N7136-597 User manual
- Type
- User manual
- This manual is also suitable for
Metropolitan N7136-597 is a versatile lighting fixture that can be installed as a pendant or semi-flush mount. With its adjustable hanging height and supporting cable, you can customize the fixture to suit your space and lighting needs. The fixture's durable construction and easy installation make it a great choice for both residential and commercial applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Metropolitan N7302-598 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Minka Lavery 3072-613 User manual
-
Minka Lavery 3071-613 User manual
-
Minka Lavery 3080-613 User manual
-
Minka Lavery 3080-613 User manual
-
George Kovacs P1702-613 User manual
-
Minka-Lavery 4072-676 User manual
-
-
Minka Group 4722-113 User manual
-
Minka Group 4723-113 User manual
