Minka Group 4588-672 User manual

Minka Group
Brand
Minka Group
Model
4588-672
Type
User manual
Page:1/2
ASSEMBLY THE FIXTURE (FIG. 1&FIG.3)
Note: Illustration (Fig. 1) on this manual is for
installation
purposes only. It may or may not be identical
to the fixture purchased.
1.
Shut of
f
power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2.
Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to
misplace any small parts
necessary for installation.
3. Attach crystal ball (T) onto tube (S).
4. Install fabric shade (M) on arms (R) using metal nuts (N)
and
place decorative ring (L）on fabric shade (M).
5. Determine t
together. Screw loop (I1) to the rod (G1). Pass the wires
carefully through each rod as you assemble. Attach
the
bottom end of rod into the coupling (J).
6. Attach quick link (H) to loop (I2) on
canopy (D). Carefully feed
the wire through loop (I1), quick link (H), and loop (I2).
7. Attach circular strap (B) to the junction box usin
g the junction
box screws (C). The side of the circular strap
(B) marked
“GND” must face out.
Mounting screw can be adjustable if
necessary.
8.
The support cable is provided to support the weight of the
fixture while wiring. Align the fixture to circular strap (B
) and
attach hook on the end of support cable (E) into a
slot located
on circular strap (B). Carefully allow the support cable (E
) to
support the weight of the fixture while wiring.
CONNECTING THE WIRES (FIG. 2)
10.
Connect the electrical wires as shown in figure 2, making
sure that all wire connectors are secured. If your j
unction box has
a ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly to
the circular strap (B) using the green screw provided.
11. Tuck the wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
12. Raise the fixture over the mounting screws (A
) and secure
with decorative nuts (F).
13. Place candle covers (Q) over sockets (V), then place
tube
covers (K) over candle covers (Q). Install (8) eight c
andelabra
base bulbs (X)
up to 60 watts each or CFL or LED equivalent (not
included) in accordance with the fixture specification—
DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
14. Attached leaf finial (O) with coupling (P).
The leaves on the lamp body can be manually adjusted to change
their shape.
Your installation is now complete. Turn on the power supply of the
junction box to test the fixture.
INSTALLATION INSTRUCTION FOR FIXTURE #4588-672
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Set A#A-020
-Circular Strap
-Ground Screw
-Mounting screws (2)
Fig.2
Rod#W35-1-11A*3PC(G2)
Rod#W35-H-11A*1PC(G1)
Fig.1
G1
G2
C
B
A
D
E
F
H
I1
I2
L
M
O
Y
W
Z
N
X
K
Q
V
J
T
S
P
R
Candle cove#CCV21082P-11A
Page:2/2
C
B
A
D
E
F
G1
H
I1
I2
a. Hardware Bag:
B. Circular Strap*1
A. Mounting Screw*2
A B C D H I
C. Screw*2
D. Canopy*1
H. Quick Link*1
I. Loop*2
F
F. Decorative Nuts*2
AA. Hex Nuts*2
A A
b. Hardware Bag:
G1. ROD 6"*1 G2G2G1
G2
G2. ROD 12"*3
Fig.3
  • Page 1 1
  • Page 2 2

Minka Group 4588-672 User manual

Minka Group
Brand
Minka Group
Model
4588-672
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents