Orbit LWP25-80W Installation guide

Brand: Orbit

Model: LWP25-80W

Type: Installation guide

Orbit LWP25-80W is a powerful and versatile LED luminaire suitable for both indoor and outdoor applications. With a power consumption of only 80W, it delivers a remarkable luminous output, making it an energy-efficient choice for various lighting needs. Its wide voltage range of 100-277V allows for flexible installation options. The LWP25-80W features advanced dimming capabilities, supporting 0-10V/PWM/VR dimming protocols, providing precise light control and creating the desired ambiance.

Orbit Industries, Inc.

INSTALLATION INSTRUCTIONS

2100 S. Figueroa St. Los Angeles, CA 90007

Tel (213) 745-8884 Fax (213) 745-2015

www.orbitelectric.com

WARNING: All work must be performed by qualified electrician. Luminaire must be installed and grounded in

accordance with the National Electrical Code (NEC) and local codes. Failure to do so may result in serious

injury and/or damage to the luminaire.

WARNING: To avoid risk of fire, explosion, or electric shock, this product should be installed, inspected, and

maintained by a qualified electrician only and in accordance with all applicable codes.

WARNING: To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminiare must be connected to a wiring system with an equipment grounding conductor.

WARNING:

Make sure the supply voltage is the same as the rated luminaire voltage.

Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

Keep lens tighly closed when in operation.

NOTE: Save these instructions for future reference.

100~277V

347~480V

LWP25 - SERIES

Category:

JUNCTION BOX (WALL) MOUNT:

1. Open the fixture head at least 90 degree

to loosen the two screws by screw driver.

2. Open and lift the fixture head from the junction box

from the hinge.

3. Fixture junction box has a guided pre-punch

holes. Check your wall junction box mounting

screws and knock-out the pre-punch holes

by a screw driver.

NOTE: Before punching the holes, check the

UP direction.

SCREW DRIVER

SCREWS

FIXTURE HEAD

HINGE

JUNCTION BOX

FIXTURE HEAD

FIXTURE

JUNCTION BOX

PRE-PUNCH HOLES

SCREW DRIVER

4. Install the fixture junction box to the wall junction

box (3O or 4O steel boxes). Remove one screw

of the wall junction box and install the slot of

fixture junction box.

WALL JUNCTION BOX

FIXTURE JUNCTION BOX

NOTE: ABOVE PICTURE IS FOR ILLUSTRATION PURPOSES ONLY.

IT MAY DIFFER IN ACTUAL INSTALLATIONS.

5. Re-install the fixture head thru the hinge of the

fixture junction box.

HINGE

JUNCTION BOX

FIXTURE HEAD

6. Attach fixture leads to line observing polarity,

black to black, white to white and green to

ground to junction box.

7. Close the fixture and tighten the two screws.

Check GASKET if sitting properly.

For better waterproofing apply a silicone

around the fixture junction box and wall

surface.

If 1/2” threaded holes on the sides is used,

apply a silicone after installation.

8. Adjust the fixture to a proper angle.

9. Turn ON power and check for proper

operation.

NOTE: PHOTOCELL IS EITHER 120V OR 277V, BEFORE INSTALLING CHECK SUPPLY VOLTAGE.

Orbit Industries, Inc.

INSTALLATION INSTRUCTIONS

2100 S. Figueroa St. Los Angeles, CA 90007

Tel (213) 745-8884 Fax (213) 745-2015

www.orbitelectric.com

MODEL NO.

INPUT VOLTAGE

WATTS

LWP25-12W 100~277V

12W

INPUT AMP.

0.15A

DIMMING

N/A

0.38A N/A

LWP25-30W 100~277V

30W

0.44A

LWP25-40W 100~277V

40W

0.22A 0-10V/PWM/VR

LWP25-40W-480V 347~480V

75W

100~277V

347~480V

LWP25 - SERIES

Category:

N/A

0.52A

LWP25-50W 100~277V

50W

N/A

1.0A

LWP25-80W 100~277V

50W

0-10V/PWM/VR

0.48A

LWP25-100W-480V

100W

0-10V/PWM/VR

347~480V

1.5A

LWP25-120W 100~277V

120W

0-10V/PWM/VR

Orbit LWP25-80W Installation guide

Orbit LWP25-80W Installation guide

Orbit LWP25-80W Installation guide

Related papers

Other documents