Alcatel-Lucent 7210 SAS-T Installation guide

7210 SAS-T

I

NSTALLATION GUIDE

August 2013

Document Part Number: 93-0475-01-01

*93-0475-01-01*

No portion of this document may be reproduced in any form or means without prior written permission from Alcatel-Lucent.

Information in this document is proprietary and confidential to Alcatel. The information in this document is subject to change. All

trademarks and registered trademarks are the property of the respective owners.

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canadian Requirements Only

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.

Japan/Nippon Requirements Only

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to

take adequate measures.

Caution:

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser

radiation exposure.

VCCI-A

7210 SAS-T Installation Guide Page 3

Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

7210 SAS-T Overview

7210 SAS-T Introduction and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Switch Architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Network Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Ethernet Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Management Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Alarm Interface Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DC power source failure detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Compact Flash Memory Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

System LEDs and Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

System and Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

System Buttons and Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Installing the 7210 SAS-T

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Ethernet Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Installing Your Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

R

ack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Desktop or Shelf Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Grounding the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Connecting to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Connecting to DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Connecting to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Warnings and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Installation Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Locking Mechanisms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Installing SFP/XFPs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Removing SFP/XFPs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Configuring the 7210 SAS-T

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Post Installation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

TABLE OF CONTENTS

Page 4 7210 SAS-T Installation Guide

Table of Contents

Initializing the System and Downloading Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Booting a 7210 SAS-T in the Lab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Booting a 7210 SAS-T from the USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Booting a 7210 SAS-T from the External Compact Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Booting a 7210 SAS-T using the image on Flash (with the image shipped by factory) . . . . . . . . . 57

Booting a 7210 SAS-T From the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Using the Out-of-Band Ethernet Management port to boot 7210 from the nework: . . . . . . . . . . . . 65

Downloading the TiMOS Software to the Internal Flash. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Establishing Router Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Telnet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Running Telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Troubleshooting

Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Power and Cooling Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

In-Band Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Appendix A: Specifications

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Japan VCCI Class A Declaration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

RoHS and WEEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Appendix B: Pin Assignments

Management Port Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Console Port Pin Assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Appendix C: Alarm Pin Assignments

Alarm Port Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

7210 SAS-T Installation Guide Page 5

LIST OF TABLES

Preface

Table 1: Information Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

7210 SAS-T Overview

Table 2: 7210 SAS-T (Non-ETR Variant) Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Table 3: 7210 SAS-T (ETR Variant) Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Table 4: Alarm Interface Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 5: Power Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Table 6: Power Source Failure Detection Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Table 7: 7210 SAS-T System LEDs and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Table 8:

System and Port Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Table 9: Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Table 10: Port LED Key Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Table 11: Front Panel Buttons and Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Installing the 7210 SAS-T

Table 12: Serial Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Configuring the 7210 SAS-T

Table 1: Console Configuration Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Troubleshooting

Table 2: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Appendix A: Specifications

Table 3: 7210 SAS-T Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Appendix B: Pin Assignments

Table 4: 10/100BASE-TX MDI and MDI-X Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Table 5:

Serial Cable Wiri ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Appendix C: Alarm Pin Assignments

Table 6: Alarm Interface Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Page 6 7750 SR-12

List of Tables

7210 SAS-T Installation Guide Page 7

LIST OF FIGURES

7210 SAS-T Overview

Figure 1: 7210 SAS-T (Non-ETR Variant) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Figure 2: 7210 SAS-T (ETR Variant) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Figure 3:

7210 SAS-T (Non-ETR Variant) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Figure 4:

7210 SAS-T (ETR Variant) Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Figure 5:

AC and DC Power Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Figure 6:

Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Figure 7: Loosening Captive Screws on the Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Figure 8: Removing the Fan Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 9: Replacing the Fan Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Figure 10: Tightening Captive Screws on the Fan Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Figure 11:

System LEDs and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Figure 12:

SFP Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Installing the 7210 SAS-T

Figure 13: Attaching the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Figure 14:

Installing the Switch in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Figure 15:

Attaching the Adhesive Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Figure 16: Connecting to a -48 VDC Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Figure 17: Connecting to a +24 VDC Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Configuring the 7210 SAS-T

Figure 1: 7210 SAS-T Boot Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Troubleshooting

Appendix A: Specifications

Appendix B: Pin Assignments

Appendix C: Alarm Pin Assignments

Figure 2: DB-15 Alarm Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Figure 3: Example for Alarm Inputs Using an External Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Figure 4: Example for Alarm Inputs Using an External Power Source. . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Page 8 7210 SAS-T Installation Guide

List of Figures

7210 SAS-T Installation Guide Page 1

Preface

About This Manual

This guide provides site preparation recommendations, step-by-step procedures to rack mount the

Alcatel-Lucent 7210 SAS-T

®

and instructions to install and configure the TiMOS software.

Each 7210 SAS-T router is shipped with rack-mounting brackets, a console cable, power cord (AC

only), and rubber feet.

Warnings and Notes

Observe the warnings and notes to avoid injury or router damage during installation and

maintenance. Follow the safety procedures and guidelines when working with and near electrical

equipment. Warning statements and notes are provided in each chapter.

Audience

This guide is intended for network installers and system administrators who are responsible for

installing, configuring, or maintaining networks. This guide assumes you are familiar with

electronic and networking technologies.

Page 2 7210 SAS-T Installation Guide

Information Symbols

Table 1 describes symbols contained in this guide.

Technical Support

If you purchased a service agreement for your 7210 SAS-T and related products from a distributor

or authorized reseller, contact the technical support staff for that distributor or reseller for

assistance. If you purchased an Alcatel-Lucent service agreement, contact technical assistance at:

http://www.alcatel-lucent.com/wps/portal/support

Table 1: Information Symbols

Symbol Meaning Description

Danger This symbol warns that improper handling and installation could result in bodily

injury. An electric shock hazard could exist. Before you begin work on this

equipment, be aware of hazards involving electrical circuitry, networking

environments, and instigate accident prevention procedures.

Caution This symbol warns that improper handling and installation could result in

equipment damage or loss of data.

Warning This symbol warns that improper handling may reduce your component or

system performance.

Note This symbol provides additional operational information.

Class 1 laser products are listed in the MDA installation guides. Only approved

Class 1 replaceable laser transceivers should be used with this product.

Class 1 Laser Product

7210 SAS-T Installation Guide Page 3

7210 SAS-T Overview

This chapter describes the 7210 SAS-T features and includes the following sections:

• 7210 SAS-T Introduction and Features on page 4

• Switch Architecture on page 6

• Features on page 7

• Hardware Description on page 9

7210 SAS-T Introduction and Features

Page 4 7210 SAS-T Installation Guide

7210 SAS-T Introduction and Features

The 7210 SAS-T is a Layer-2 service-aware Ethernet-capable switch. The switch is available as

two variants, as follows:

• 7210 SAS-T (Non-ETR variant) with support for up to 12 100/1000 fiber-optic SFP ports,

10 10/100/1000 Copper SFP ports and 4 XFP-based 10 Gig ports

• 7210 SAS-T (ETR) with support for up to 12 100/1000 fiber-optic SFP ports, 6 10/100/

1000 Copper SFP ports, 4 XFP based 10 Gig ports and 4 Power over Ethernet (PoE) ports

Figure 1: 7210 SAS-T (Non-ETR Variant) Front Panel

The 7210 SAS-T (Non-ETR variant) includes the following features:

• 12 100/1000 fiber-optic SFP ports

• 10 10/100/1000 Base-T fixed Copper ports

• Four XFP-based 10 Gig ports

• Option to use redundant power supplies

• One single fan tray with 3 fans and a fan filter

• One RJ-45 management port for firmware upgrade or system management

• One RJ-45 console (RS-232 interface) connector for device management

• One DB15 connector alarm port

• Two BITS ports (reserved for future use)

• Two timing output jacks (1 PPS, 10 MHz) (reserved for future use)

• One USB port and One external removable CF memory card slot (cf2:\)

• One OMC (Optical Management Console) port

• One reset button

• Embedded SR OS

• Compact size: 1.5RU height, 19-inch rack-mountable metal enclosure, 10-inch depth (ETSI)

Crit

Maj

Fan

Status

PS1

PS2

USB

Alarm

+24V +12V

+24V

DC PEM

200W

+24V +12V

+24V

DC PEM

200W

CF2

OMC

23 24 25 26

Management

Fan

1PPS

BITS2/ToD2

BITS1/ToD1

10MHz

ACO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

–A

+A

–B

+B

SAS_T_005

Reset

7210 SAS-T Overview

7210 SAS-T Installation Guide Page 5

Figure 2: 7210 SAS-T (ETR Variant) Front Panel

The 7210 SAS-T (ETR variant) include the following features:

• 12 100/1000 fiber-optic SFP ports

• 10 10/100/1000 Base-T fixed Copper ports

• Four PoE Copper ports (out of the total 10 copper port)

• Four XFP-based 10 Gig ports

• Option to use redundant power supplies

• One single fan tray with 3 fans and a fan filter

• One RJ-45 management port for firmware upgrade or system management

• One RJ-45 console (RS-232 interface) connector for device management

• One DB15 connector alarm port

• Two BITS ports(reserved for future use)

• Two timing output jacks (1 PPS, 10 MHz) (reserved for future use)

• One USB port and One external removable CF memory card slot (cf2:\)

• One OMC (Optical Management Console) port

• One reset button

•Embedded SR OS

• Compact size: 1.5RU height, 19-inch rack-mountable metal enclosure, 10-inch depth (ETSI)

Crit

Maj

Fan

Status

PS1

PS2

USB

Alarm

+24V +12V

+24V ETR

DC PEM

200W

+24V +12V

+24V ETR

DC PEM

200W

CF2

OMC

23 24 25 26

Management

POE

Fan

1PPS

BITS2/ToD2

BITS1/ToD1

10MHz

ACO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

–A

+A

–B

+B

SAS_T_002

Reset

Note: The OMC port, the BITS ports, the 1PPS interface and the 10MHz are reserved for

future use and is not currently supported.

Switch Architecture

Page 6 7210 SAS-T Installation Guide

Switch Architecture

The 7210 SAS-T employs a wire-speed, non-blocking switching fabric. This permits simultaneous

wire-speed transport of multiple packets at low latency on all ports.

Network Management Options

This switch contains a comprehensive array of LEDs for at-a-glance monitoring of network and

port status. It also includes a management agent that enables you to configure or monitor your

switch using its CLI, or by using SNMP applications.

To manage the switch, you can make a direct connection to the console port (out-of-band Ethernet

management port) or you can manage it by using a network connection (in-band SFP or XFP

ports) using Telnet/SSH or SNMP-based network management software (such as ALU 5620

SAM).

The management port provides a dedicated management channel that operates outside of the data

transport network. This makes it possible to reconfigure or troubleshoot the switch over either a

local or remote connection to the management port when access using the data channel is not

possible or deemed insecure.

7210 SAS-T Overview

7210 SAS-T Installation Guide Page 7

Features

The 7210 SAS-T includes the following features:

• All connections front facing

• Wire speed, non-blocking, service-aware layer-2 switch

• 12 100/1000 fiber-optic SFP ports

• 10 10/100/1000 Base-T fixed Copper ports

• Four PoE Copper SFP ports (out of the 10 Copper ports)

• Four XFP-based 10 Gig ports

•Powered by SR OS

• Per-service quality of service (QoS) with up to eight levels of class-based queuing per port

• Per-service OAM toolkit with IEEE 802.1ag, IEEE 802.3ah and local service mirroring

• Supports NULL, Dot1Q access and QinQ SAPs.

• Dual-homed connections uplinks to separate aggregation devices

• Flexible deployment options with support for mesh and ring topologies

• MEF 9 and MEF 14 compliant platform

• Managed by the 5620 SAM

• Provides four isolated alarm inputs and two dry contacts that relay outputs through a

DB-15 interface on the front panel. Option to supply power to the devices connected to

alarm inputs.

• Hot-swappable, redundant, load sharing AC or DC power and fan modules

• Front-removable fan tray with removable air filter

• 7210 SAS-T (non-ETR variant): power ~ 130W

• 7120 SAS-T (ETR variant): power ~ 200W (includes 60W for four optional PoE ports)

• DC input connection screw terminal based

• 1.5U rack mountable or desktop, depth target 255 mm

• Multi-core CPU with 1GB RAM

• Compact Flash-based field replaceable flash memory

• USB port for using USB storage sticks/devices.

• OMC (Optical Management Console) port to connect up to 4 1830 VWM devices.

• Front panel accessible reset button

• DC Input power detection

Features

Page 8 7210 SAS-T Installation Guide

• Temperature monitoring functions

• Console and management ports

• Sync E & 1588 support

• 7210 SAS-T has an operating range of 0 Celsius to 40 Celsius

• 7210 SAS-T ETR variant has an environmental rating of -40 to +65 degree C operation

Connectivity

The 7210 SAS-T includes the following connectivity features:

• 10/100/1000 Base-T fixed Copper ports

• 100/1000 fiber-optic SFP ports

• 10G XFP ports

• IEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit Ethernet, and Ten-Gigabit compliance

ensures compatibility with standards-based network cards and switches from any vendor.

7210 SAS-T Overview

7210 SAS-T Installation Guide Page 9

Hardware Description

Figure 3: 7210 SAS-T (Non-ETR Variant) Front Panel

Crit

Maj

Fan

Status

PS1

PS2

USB

Alarm

–48V +12V

DC

PEM

200W

–48V +12V

DC

PEM

200W

CF2

OMC

23 24 25 26

Management

Fan

1PPS

BITS2/ToD2

BITS1/ToD1

10MHz

ACO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

–A

+A

–B

+B

SAS_T_012

135 8 14 11 1217

21 4

9 16

Reset

3

6

7

10

15

Table 2: 7210 SAS-T (Non-ETR Variant) Front Panel Features

Key Description

1 Ground and DC power connection

2 Power trays

3 LEDs

4 Alarm connector

5USB port

6 Alarm cut off button

7 Reset button

8 External Compact Flash memory card slot (cf2:\)

9 100/1000 fiber-optic SFP ports

10 Management port

11 Console port

12 Fan tray

Hardware Description

Page 10 7210 SAS-T Installation Guide

Figure 4: 7210 SAS-T (ETR Variant) Front Panel

13 BITS timing ports (reserved for future use)

14 OMC (Optical Management Console) port

(reserved for future use)

15 1PPS timing output and 10 Mhz timing output

(reserved for future use)

16 10/100/1000 Base-T fixed Copper ports

17 10Gig XFP ports

Table 2: 7210 SAS-T (Non-ETR Variant) Front Panel Features

Key Description

Crit

Maj

Fan

Status

PS1

PS2

USB

Alarm

–48V +12V

DC ETR

PEM

200W

–48V +12V

DC ETR

PEM

200W

CF2

OMC

23 24 25 26

Management

POE

Fan

1PPS

BITS2/ToD2

BITS1/ToD1

10MHz

ACO

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

–A

+A

–B

+B

SAS_T_009

135 8 14 11 1217

21 4

9 16

Reset

3

6

7

10

15

18

Table 3: 7210 SAS-T (ETR Variant) Front Panel Features

Key Description

1 Ground and DC power connection

2 Power trays

3 LEDs

4 Alarm connector

7210 SAS-T Overview

7210 SAS-T Installation Guide Page 11

5USB port

6 Alarm cut off button

7 Reset button

8 External Compact Flash memory card slot (cf2:\)

9 100/1000 fiber-optic SFP ports

10 Management port

11 Console port

12 Fan tray

13 BITS timing ports (reserved for future use)

14 OMC (Optical Management Console) port

(reserved for future use)

15 1PPS timing output and 10 Mhz timing output

(reserved for future use)

16 10/100/1000 Base-T fixed Copper ports

17 10Gig XFP ports

18 PoE power ports

Table 3: 7210 SAS-T (ETR Variant) Front Panel Features

Key Description

Hardware Description

Page 12 7210 SAS-T Installation Guide

Ethernet Interfaces

The 7210 SAS-T provides 12 100/1000 fiber-optic SFP ports. Each port can be used for a direct

connection to a subscriber’s Customer Premises Equipment (CPE), or as an uplink to another

aggregation node. The 7210 SAS-T supports 10/100/1000 Base-T copper SFPs. The 7210 SAS-T

also provides ten 10/100/1000 Base-T fixed Copper ports. There are four XFP ports, which support

10G redundant network uplinks to another aggregation node or provide 10G redundant

connectivity to a subscriber's CPE. In addition, the 7210 SAS-T ETR variant supports four power-

over-Ethernet (PoE) ports.

Management Port

The management port provides a dedicated management interface that is segregated from data

traffic crossing the other ports.

Alcatel-Lucent 7210 SAS-T Installation guide

Related papers

Other documents