AEM 30-2067 Operating instructions

Brand: AEM

Model: 30-2067

Type: Operating instructions

AEM 30-2067: Unleash the Power of Precise Air/Fuel Ratio Monitoring

The AEM 30-2067 UEGO Wideband Air/Fuel Ratio Controller is your ultimate companion for accurate air/fuel ratio monitoring and engine tuning. With its cutting-edge technology, this device delivers unparalleled performance, ensuring that your engine operates at its peak efficiency.

Key Features:

Lightning-Fast Response: Experience real-time air/fuel ratio readings with an impressive response time of less than 100 milliseconds. This responsiveness allows you to make quick and precise adjustments to your engine's fuel mixture, resulting in optimized performance.

AEM 30-2067: Unleash the Power of Precise Air/Fuel Ratio Monitoring

Key Features:

Lightning-Fast Response: Experience real-time air/fuel ratio readings with an impressive response time of less than 100 milliseconds. This responsiveness allows you to make quick and precise adjustments to your engine's fuel mixture, resulting in optimized performance.

INSTALLATION

1. Disconnect the negative battery cable.

2. Using the supplied Stainless Steel 1/8”NPT compression mount, mount the EGT

thermocouple as shown in Figure 2. Common locations for mounting the EGT

thermocouple are 1-2 inches from the exhaust port, 2-3 inches before the turbine

inlet, or in the header collector.

3. Connect the EGT thermocouple to the extension harness as shown in Figure 3.

4. Connect the 3-pin connector on the thermocouple extension harness to either the

EGT 1 location or EGT 2 location as shown above in Figure 1.

When using both thermocouples for comparison (bank 1 EGT and bank 2 EGT for

example), make sure to mount both thermocouples in a similar fashion (distance from

port, tip depth, tube diameter, etc) so the readings are not influenced by installation

differences.

AEM Performance Electronics

2205 126

Street Unit A, Hawthorne, CA. 90250

Phone: (310) 484-2322 Fax: (310) 484-0152

http://www.aemelectronics.com

Instruction Part Number: 10-2320 Rev 01

 2009 AEM Performance Electronics

AEM X-WIFI EGT Connection Guide

Figure 1. Wiring Schematic

Page 2

Connecting the Thermocouple

Slide the supplied heat shrink onto the sensor cable. Connect the RED wire from the

thermocouple to the RED wire on the harness and the YELLOW wire from the

thermocouple to the YELLOW wire on the harness using the supplied 4-40 screws and

hex nuts. Make sure the connections are not touching. Center the heat shrink over the

connections and apply mild heat to the heat shrink until it shrinks over the connections.

See Figure 7.

Notes

If further tuning help is needed be sure to visit the video gallery or performance

electronics forum at www.aemelectronics.com for comprehensive instructional videos

and information.

A more detailed version of the instruction manual is available for download at

www.aemelectronics.com.

FERRULE SLEEVE

COMPRESSION NUT

THREADED BODY

PIPE/MANIFOLD

WITH 1/8” NPT

THREADS OR

13/32” HOLE

TIP OF THERMOCOUPLE

NEAR CENTER OF

PIPE/MANIFOLD

Figure 2. Thermocouple Mounting

HEAT SHRINK

Figure 3. Thermocouple to Cable Connection

AEM 30-2067 Operating instructions

Brand: AEM

Model: 30-2067

Type: Operating instructions

AEM 30-2067: Unleash the Power of Precise Air/Fuel Ratio Monitoring

Key Features:

Lightning-Fast Response: Experience real-time air/fuel ratio readings with an impressive response time of less than 100 milliseconds. This responsiveness allows you to make quick and precise adjustments to your engine's fuel mixture, resulting in optimized performance.

Download PDF

report

AEM 30-2067 Operating instructions

AEM 30-2067 Operating instructions

Related papers

Other documents