Page is loading ...
Isole NN1A–NN1G
Nendo & Luca Nichetto
2017
Congratulations on choosing this original Isole modular
system designed by Nendo and Luca Nichetto. We hope you
will enjoy using this product and follow these instructions
to ensurecorrect assembly. If you have any questions or
comments, please do not hesitate to contact us by mail on:
Instructions
Please read these instructions carefully and retain them for future
reference to ensure that the table is used correctly. For your own safety,
please study each step of this instruction manual. &Tradition is not
responsible for any faults or damages caused by not following these
instructions correctly.
Safety precautions
- Dispose of all plastic bags and foam from the packaging and do not allow
children to play with it.
- The modules are only intended for interior use.
- Do not assemble alone.
- To avoid deformation of the legs, please do not lift assembled modules
consisting of more than two seats. Moving of modules consisting of three
or more seats requires disassembly of the modules.
- Handle table tops with care in order not to scratch surface during
assembly.
- Screw might be oiled, so be aware not to get any oil on to the upholstery.
- Take special notice to length of bolts, as too long bolts can damage
certain parts.
- Spilled liquids of any kind should be removed immediately from the table
top as it may penetrate the surface treatment and cause damage to it.
Cleaning instructions
The Isole modules are made from molded CMHR foam with metal inserts
and no-sag springs. The legs are made from powder coated steel and the
table tops from solid colored black MDF with Fenix NTM nano laminate on
the top.
- Textile: Dust and dirt will wear down the textile. For daily cleaning,
vacuum the modules with a soft brush mouth piece. For more severe
cleaning and stain removal, please see: www.febrik.com.
- Legs : Clean powder coated steel legs with a soft cloth wrung in a solution of
water and universal cleaning detergent and dry immediately with a soft cloth.
- Table top: Dust Nano laminate table top with a soft cloth. Clean laminate
table top with a soft cloth wrung in a solution of water and universal
cleaning detergent and dry immediately with a soft cloth. Avoid use of
abrasive cleaning products such as steel wool or polish.
Tools needed
- Allen Key - supplied
- Allen Key developed for power tool - supplied
For faster assembly it is recommended to use a power tool. Take care not
to overtighten the screws as this may cause permanent damage.
I
B
B
E
B
B
G
G
Overview
Order nr. 7365
Seat - 6pcs.
Back - 3pcs.
Armrest - 0pcs.
Tabletop T2 -2pcs.
Leg B - 4pcs.
Leg G - 2pcs.
Leg I - 1pcs.
Leg E - 1pcs.
Bolt M6x20 - 32pcs. (Short)
Bolt M6x25 - 96pcs. (Long)
Step 1
Make sure that all parts listed are supplied and accounted for. See part
list next to overview image on the previous page. Please note that there
are two dierent bolt length and that they have dierent placements.
Step 2
First, turn the seats, back and armrest upside down for better access and
easier assembly.
Step 3
Seats
Start by assembling legs to the seats.
Locate the correct leg (see overview image), place it on the bottom of
the seat and align the holes.
Insert the supplied M6x25 bolts (long bolts) into the holes and tighten
using the supplied tool.
Step 4
Back & armrest
Once the legs are fastened to the seat, locate the corresponding back or
armrest (see overview image).
Insert the bottom pin into the leg and align the holes.
Insert the supplied M6x20 bolts (short bolts) into the holes and tighten
using the
supplied tool.
Step 5
Table
Lastly, locate the corresponding sidetable, if included (see overview image).
Place it beneath the leg and align the holes.
Insert the supplied M6x20 bolts (short bolts) into the holes and tighten
using the
supplied tool.
Step 6
Once all the parts have been assembled and fastened carefully flip the
module around.
ATTENTION: If the module consists of more than two seats more than
one person is needed to flip it around, in order to avoid deformation of
the legs.
Tables Seats
Backs & Armrests
Legs
Bolts M6 Allen Keys
Floor mount - optional
Step 1
Choose a leg for the floor mount.
Using a flat screwdriver, or a similar tool, carefully remove the existing
glider from the bottom of the leg.
Step 2
Remove the set screw from the floor mount and place it on the leg.
Step 3
Place the Isole module in its destined location and, using a pencil, mark the
base of the floor mount.
Next, remove the Isole module and floor mount and drill a hole in the
center of the cirle you have drawn.
NB: Consult with a profesional before drilling into the floor, as plugs or
other measures might need to be taken.
Step 4
Remove the floor mount from the leg and place it over the hole. Insert
a suitable bolt and tighten, making sure that the floor mount is firmly
attached to the floor.
Step 5
Place the leg into the floor mount, insert the set crew and tighten, so as to
assure that the leg can not be moved.
/
