OBU 206
PRODUCT DESCRIPTION SHEET
DE AT FR NL BE ES IT SE NO DK FI PL CZ SK HU RU
5019 610 54442
0
Off
Oven light
STATIC FUNCTION
Use when all the food is on the same runner level.
-
Pre-heat the oven to the required cooking temperature and place the food inside as soon as the red
thermostat indicator light switches off.
-
Ideally, the shelf should be on the second runner level when using the static function.
STATIC FUNCTION + FAN
Use this function when cooking on two different levels.
-
Oven pre-heating is not necessary (except for pizzas and focaccia).
-
Switch the position of the dishes in the oven 10 minutes before the end of cooking time.
-
Remove the cooked dish and, if necessary, continue cooking the other one for as long as required.
GRILL FUNCTION
Use the grill function to cook small pieces of meat (steaks, sausages) and for making toasts.
-
The oven door must be closed during the cooking cycle.
-
Pre-heat the grill for about 5 minutes.
-
Arrange the meat on the grid with the drip tray underneath. Pour water in the drip tray to cover the bottom to
reduce smoke and fat spatters.
-
Turn over the meat about half-way through cooking time.
GRILL + FAN FUNCTION
Ideal for large joints, pork, chicken and roast beef.
-
The oven door must be closed during the cooking cycle.
-
Place the meat on the grid with the drip tray underneath. Pour water in the drip tray to cover the bottom to
reduce smoke and fat spatters.
-
Turn over the meat about half-way through cooking time.
DEFROST FUNCTION
Ideal for thawing frozen food to room temperature.
-
The food should be inserted in the oven in its wrapping to prevent it from drying out.
Turn the selector knob to the required symbol.
The oven light switches on.
• Turn the thermostat knob clockwise to the required temperature.
The red thermostat indicator light switches on.
• When the required temperature is reached, the red thermostat indicator light switches off.
End of cooking cycle:
• Return the knobs to the OFF position (0 - •).
1.
Turn the knob fully clockwise.
2.
Return the knob to the required cooking time.
3.
When the preset cooking time has elapsed, the oven switches off.
-
To use the oven without programming the cooking time, set the knob to .
Warning:
If the programmer is on “0” the oven will not switch on: to switch on the oven,
either set the programmer knob to or set the required cooking time.
OVEN
First
Last
First...Last
: Runner positions
1.
Control panel
2.
Cooling fan (not visible)
3.
Upper heating element
4.
Grill element (can be lowered)
5.
Oven light
6.
Fan
7.
Lower heating element (not visible)
8.
Oven door hinges
9.
Oven cool door
Accessories :
•Grid
• Baking tray
• Drip tray
CONTROL PANEL
1
Oven functions selector knob
2.
Oven thermostat knob
3.
Thermostat indicator light
4.
Mechanical Automatic Off
5.
Cooktop control knob
0 1 ...
10
*
6.
Cooktop control knob
0 1 ...
10
*
7.
Cooktop control knob
0 1 ...
10
*
8.
Cooktop control knob
0 1 ...
10
*
9.
Cooktop “ON” indicator light
*The cooktop control knobs are not interchangeable. After cleaning or servicing, they must be returned
to their original positions (see the above diagram next to each knob).
N.B.: The cooling fan can runs continuously at different speed according to the temperature value of the
components when the cooktop or the oven are in use.
The fan may continue to run for the time necessary to ensure sufficient cooling of the components and
adjacents kitchen units after the appliances have been switched off.
OVEN FUNCTIONS
SWITCHING THE OVEN ON
PROGRAMMING COOKING TIME
5019 610 54442
The cooktop control knobs are marked with a numerical scale corresponding to different power settings,
and a series of function symbols.
KEEP WARM FUNCTION
This function uses a low power setting so that food can be kept warm when cooking is finished.
How to operate:
1.
Turn the knob to .
2.
To deactivate the Keep Warm function, change the knob position.
DUAL ZONE FUNCTION
(DEPENDENT ON MODEL)
This function is available on the front left and rear left cooking zones. The dual-zone function extends the
heated area of the cooktop so that you can use large, oval or rectangular pans.
How to operate:
1.
Turn the knob to and wait for the residual heat indicator for the chosen hotplate to start flashing.
2.
Select the required power by turning the knob anti-clockwise. The residual heat indicator remains lit to show
that the cooktop is switched on.
3.
To deactivate the function return the knob to
“0”
.
FAST BOILING FUNCTION
This function makes it possible to bring water to the boil fast; the Fast Boiling function remains active for a
preset time. Once the preset time has elapsed, the cooktop returns automatically to maximum power level.
The Fast Boiling function can be activated also once you have already started cooking.
Warning:
Make sure you have placed the pan on the cooking zone before activating the fast boiling
function or the glass-ceramic surface may be damaged.
Specified performance values for the Fast Boiling function are guaranteed for all types of glass-ceramic cooktops.
How to operate:
1.
Place the pan on the chosen cooking zone.
2.
Set
the knob to .
GENTLE HEAT FUNCTION
Can be used to raise dough, soften hard butter from the fridge, keep a baby’s bottle or a baby food warm,
for yoghurt making, melting chocolate, etc...
This function is available only when the residual heat indicator light is on.
How to operate:
1.
Make sure that the relative cooking zone residual heat indicator light is on.
2.
Turn the knob to .
3.
To deactivate the function change the knob position.
COOKTOP FUNCTIONS
This symbol does not correspond to any
cooktop mode; the heating element is not
powered.
-
1
-
2
IKEA OBU 206 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
IKEA OBU 246 W Program Chart
-
-
-
Whirlpool OBU 228 B Owner's manual
-
-
-
-
Whirlpool OBU 207 W User guide
-
Whirlpool AKZ 276 IX User guide
-
Other documents
-
Bauknecht ESZB 5463 BR Program Chart
-
-
-
-
-
-
-
-
-