JDS Uniphase 4100 User manual

Category
Measuring, testing & control
Type
User manual

This manual is also suitable for

2100/4100 OTDR Modules
OTDR Modules for T-BERD/MTS-2000 and T-BERD/MTS-4000
Handheld Modular Test Set
User Manual
MTS2100 4100 Module US rev08.book Page i Jeudi, 1. août 2013 1:43 13
MTS2100 4100 Module US rev08.book Page ii Jeudi, 1. août 2013 1:43 13
2100/4100 OTDR Modules
OTDR Modules for T-BERD/MTS-2000 and T-BERD/MTS-4000
Handheld Modular Test Set
User Manual
MTS2100 4100 Module US rev08.book Page iii Jeudi, 1. août 2013 1:43 13
MTS2100 4100 Module US rev08.book Page iv Jeudi, 1. août 2013 1:43 13
User Manual 770000102/08 v
Notice
Every effort was made to ensure that the information in this document
was accurate at the time of printing. However, information is subject to
change without notice, and JDSU reserves the right to provide an
addendum to this document with information not available at the time that
this document was created.
Copyright
© Copyright 2013 JDSU, LLC. All rights reserved. JDSU, Enabling
Broadband and Optical Innovation, and its logo are trademarks of JDSU,
LLC. All other trademarks and registered trademarks are the property of
their respective owners. No part of this guide may be reproduced or
transmitted electronically or otherwise without written permission of the
publisher.
Trademarks
JDSU and MTS/T-BERD 2000/4000 are trademarks or registered trade-
marks of JDSU in the United States and/or other countries.
Microsoft, Windows, Windows CE, Windows NT, and Microsoft Internet
Explorer are either trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Netscape Navigator is a trademark or registered trademark of Netscape
Communications Corporation in the United States and other countries.
Ordering
information
This guide is a product of JDSU's Technical Information Development
Department, issued as part of the User Manual.
WEEE Directive
Compliance
JDSU has established processes in compliance with the Waste Electrical
and Electronic Equipment (WEEE) Directive, 2002/96/EC.
This product should not be disposed of as unsorted municipal waste and
should be collected separately and disposed of according to your
national regulations. In the European Union, all equipment purchased
from JDSU after 2005-08-13 can be returned for disposal at the end of
its useful life. JDSU will ensure that all waste equipment returned is
reused, recycled, or disposed of in an environmentally friendly manner,
and in compliance with all applicable national and international waste
legislation.
It is the responsibility of the equipment owner to return the equipment to
JDSU for appropriate disposal. If the equipment was imported by a
reseller whose name or logo is marked on the equipment, then the owner
should return the equipment directly to the reseller.
MTS2100 4100 Module US rev08.book Page v Jeudi, 1. août 2013 1:43 13
vi User Manual 770000102/08
Instructions for returning waste equipment to JDSU can be found in the
Environmental section of JDSU’s web site at www.jdsu.com. If you have
questions concerning disposal of your equipment, contact JDSU’s
WEEE Program Management team at WEEE.EMEA@jdsu.com.
MTS2100 4100 Module US rev08.book Page vi Jeudi, 1. août 2013 1:43 13
User Manual 770000102/08 vii
Table of Contents
About This Guide xv
Purpose and scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Technical assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Recycling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii
Chapter 1 Principle of Measurement 1
Principle of reflectometry measurements . . . . . . . . . . . . . . . . . 2
Information yielded by the measurement . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Validity of Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Reflectance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Principle of optical power and attenuation measurements . . . . . .4
Power measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Attenuation measurements (optical link loss) . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 2 Starting up 7
Unpacking the device - Precautions . . . . . . . . . . . . . . . . . . . . . . 8
Fitting and removing a module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MTS2100 4100 Module US rev08.book Page vii Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 viii
Fitting a module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing a module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Universal connectors and adapters . . . . . . . . . . . . . . . . . . . . . . . .10
Adapter types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switching adapter type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Changing the adapter on a LA OTDR Module . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning universal connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3 Activating OTDR function 13
Selecting the SmartOTDR™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Principle of the SmartOTDR™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting SmartOTDR™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting the OTDR Expert function . . . . . . . . . . . . . . . . . . . . . . .15
Principle of the OTDR Expert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting OTDR Expert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4 Configuring the reflectometry test 17
Configuring the unit for SmartOTDR™ . . . . . . . . . . . . . . . . . . 18
Selecting the configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Modifying some parameters before the acquisition . . . . . . . . . . . . . . . . . . 19
Configuring the test in OTDR Expert . . . . . . . . . . . . . . . . . . . . . . .20
Configuring the Acquisition parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Launch cable parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Configuring the Alarms parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configuring the Measurement parameters . . . . . . . . . . . . . . . . . . . . . . . . . 25
Measurement parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Detection parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Configuring the Link parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuring the file storage parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Configuration in Test Auto mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Saving configuration parameters in a file . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Loading an existing configuration file in ExpertOTDR . . . . . . . . . . . . . . . . 34
MTS2100 4100 Module US rev08.book Page viii Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 ix
Chapter 5 Launching a reflectometry test and displaying results 37
Performing OTDR acquisitions . . . . . . . . . . . . . . . . . . . . . . . . . 38
Performing an acquisition in Real Time mode . . . . . . . . . . . . . . . . . . . . . . 38
Principle of the Real time mode . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Performing acquisition in Real Time . . . . . . . . . . . . . . . . . . . . . . . .38
Stopping the real time acquisition . . . . . . . . . . . . . . . . . . . . . . . . . .39
Performing a measurement with SmartOTDR™ . . . . . . . . . . . . . . . . . . . . 40
Performing an acquisition with OTDR Expert . . . . . . . . . . . . . . . . . . . . . . . 40
Performing an acquisition from Results page . . . . . . . . . . . . . . . . . . . . . . . 42
Multi-wavelength acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Actions on trace during acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Results display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Common functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Display of events on the trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Results table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Cursors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Zoom function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Shift function (OTDR Expert only) . . . . . . . . . . . . . . . . . . . . . . . . . .51
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Display of traces in overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Traces display in double acquisition mode . . . . . . . . . . . . . . . . . . .54
Advanced functions in OTDR Expert mode . . . . . . . . . . . . . . . . . .54
Automatic measurement and detection . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Addition of events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Manual measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Measurements of slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Measurement of ORL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Measurement of Reflectance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Splice measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Memorization of the position of events . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Overlay trace function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Overlaying several traces stored in memory . . . . . . . . . . . . . . . . . .62
Display of traces in overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Adding traces in overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Swapping overlay traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Removing a trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Quitting the overlay menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Reference Trace function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Use of the reference trace function in the Result page . . . . . . . . . .63
Using the reference trace function in the explorer . . . . . . . . . . . . . .64
SLM (Smart Link Mapper) option . . . . . . . . . . . . . . . . . . . . . . . . . .65
Show the detailed information of one event . . . . . . . . . . . . . . . . . . . . . . . . 66
MTS2100 4100 Module US rev08.book Page ix Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 x
Event View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Changing the type of an event . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
OptiPulses option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Configuring the OTDR acquisition with OptiPulses mode . . . . . . . . . . . . . 68
Results in OptiPulses mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Saving the trace(s) and generating a report . . . . . . . . . . . . . . . . .70
Saving results and creating a report from results page . . . . . . . . . . . . . . . 70
Opening a report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Storing OTDR measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Recalling OTDR files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Chapter 6 FTTA-SLM Software option 75
Principle of FTTA-SLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Acceptance Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Troubleshooting Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Configuring the Reflectometry test for FTTA network . . . . . . . . .78
FTTA setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Alarms parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
File parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Launching the acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Results page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Trace View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
SmartLink view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Displaying the details of an event . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Event View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Changing the name of an event . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Saving the trace(s) and generating a report . . . . . . . . . . . . . . . . .87
Saving results and creating a report from results page . . . . . . . . . . . . . . . 88
Opening a report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Chapter 7 Power meter and Source options of the OTDR Modules 91
Connection to the power meter . . . . . . . . . . . . . . . . . . . . . . . . 92
Configuring the Power meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Configuring the measurement parameters of the power meter . . . . . . . . . 93
Configuring the alarm parameters of the power meter . . . . . . . . . . . . . . . . 94
Activating the Source function . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
MTS2100 4100 Module US rev08.book Page x Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 xi
Result page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Result page of the Power meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Table of results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Commands of the power meter parameters . . . . . . . . . . . . . . . . . .96
Result page of the Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Performing the power level measurement . . . . . . . . . . . . . . . . . .97
Performing the insertion loss measurement . . . . . . . . . . . . . . . . .98
Setting the zero value of the power meter . . . . . . . . . . . . . . . . . . . . . . . . . 98
Carrying out the reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Carrying out the side by side reference . . . . . . . . . . . . . . . . . . . . . .99
Carrying out the reference in loopback mode . . . . . . . . . . . . . . . .100
Measurements on the fiber under test . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Storing and reloading results . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
File Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Storing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Loading results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Chapter 8 FiberComplete Modules 103
General introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Activating the function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Establishing References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Reference stage process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Loopback Referencing method . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Side-by-Side referencing method . . . . . . . . . . . . . . . . . . . . . . . . . 110
Configuring the units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Configuring the acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Configuring the file saving for FiberComplete results . . . . . . . . . . . . . . . . 115
Saving the parameters from FiberComplete configuration . . . . . . . . . . . . 116
Loading a configuration file FiberComplete . . . . . . . . . . . . . . . . . . . . . . . 116
Performing the tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Sending a message to the distant Platform . . . . . . . . . . . . . . . . . . . . . . . 117
Starting the test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Results screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Cable view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Fiber View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Fault Finder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
MTS2100 4100 Module US rev08.book Page xi Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 xii
OTDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Saving results and generating a report . . . . . . . . . . . . . . . . . . . .122
Saving results and creating a report from results page . . . . . . . . . . . . . . 122
Opening a report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
File management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Storing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Filenaming convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Chapter 9 File management 127
File Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Managing tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
File signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
File configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Dir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Rules for naming files (Filenaming parameter) . . . . . . . . . . . . . . . 130
Name of a file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Save mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Auto store . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Change Fiber Nbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Fiber/Link Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Fiber ID and Fiber Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Cable Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132
Location A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Location B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
Comment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
File export (T-BERD/MTS 4000 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Buttons on the right of the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Explorer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Description of the explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Storage media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Storage media built into the Platform . . . . . . . . . . . . . . . . . . . . . .135
External USB storage media . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Remote T-BERD/MTS and data transfer . . . . . . . . . . . . . . . . . . . .136
Abbreviations for storage media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Directories and files edit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Saving files from the Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
MTS2100 4100 Module US rev08.book Page xii Jeudi, 1. août 2013 1:43 13
Table of Contents
User Manual 770000102/08 xiii
Loading files and displaying traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Simple loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Loading several traces in overlay . . . . . . . . . . . . . . . . . . . . . . . . .137
Load with configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
Exporting files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Explorer/Link Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
Editing function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Exporting a directory in a txt file . . . . . . . . . . . . . . . . . . . . . . . . . . .139
Generating pdf report(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Using the Merge key, with the txt/pdf files . . . . . . . . . . . . . . . . . . . 141
Sending files by e-mail (T-BERD/MTS 4000 only) . . . . . . . . . . . . . 142
Chapter 10 Technical specifications 143
OTDR modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Characteristics of reflectometry measurements . . . . . . . . . . . . . . . . . . . . 144
Manual Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Typical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Class of the lasers of the OTDR modules . . . . . . . . . . . . . . . . . . . . . . . . 148
OTDR modules measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Technical specifications of the Power meter function on module . .
148
Technical specifications of the Source function on module . . .149
Technical specifications of the FiberComplete modules . . . . . .150
Chapter 11 Options and accessories 151
References of measurement modules . . . . . . . . . . . . . . . . . . 152
OTDR Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
FiberComplete module with OTDR function . . . . . . . . . . . . . . . . . . . . . . . 153
FiberComplete module with Fault Finder function . . . . . . . . . . . . . . . . . . 153
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
User manual references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
References of optical connectors and adapters . . . . . . . . . . . . .154
Index 157
MTS2100 4100 Module US rev08.book Page xiii Jeudi, 1. août 2013 1:43 13
Table of Contents
xiv User Manual 770000102/08
MTS2100 4100 Module US rev08.book Page xiv Jeudi, 1. août 2013 1:43 13
User Manual 770000102/08 xv
About This Guide
The T-BERD/MTS-2000/4000 of JDSU provides a handheld, modular
platform designed for the construction, validation and maintenance of
fiber networks.
The topics discussed in this chapter are as follows:
“Purpose and scope” on page xvi
“Assumptions” on page xvi
“Technical assistance” on page xvi
“Technical assistance” on page xvi
“Conventions” on page xvii
MTS2100 4100 Module US rev08.book Page xv Jeudi, 1. août 2013 1:43 13
About This Guide
Purpose and scope
xvi
User Manual 770000102/08
Purpose and scope
The purpose of this guide is to help you successfully use the T-BERD/
MTS-2000/4000 features and capabilities. This guide includes task-
based instructions that describe how to install, configure, use, and trou-
bleshoot the T-BERD/MTS-2000/4000 with modules.
Assumptions
This guide is intended for novice, intermediate, and experienced users
who want to use the T-BERD/MTS-2000/4000 effectively and efficiently.
We are assuming that you have basic computer and mouse/track ball
experience and are familiar with basic telecommunication concepts and
terminology.
Technical assistance
If you need assistance or have questions related to the use of this
product, call or e-mail JDSU’s Technical Assistance Center for customer
support.
Table 1 Technical assistance centers
Region Phone Number
Americas
Talcum Products
866 228 3762
World Wide: 301 353 1550
tac@jdsu.com
Europe, Africa, and
Mid-East
+49 (0) 7121 86 1345
(Europe)
hotline.europe@jdsu.com
+33 (0) 1 30 81 50 60
(JDSU France)
support.france@jdsu.com
Asia and the Pacific
Southeast Asia, Aus-
tralia, and New Zea-
land
+852 2892 0990
(Hong Kong)
+86 10 6833 7477
(Beijing-China)
All others 866 228 3762 tac@jdsu.com
MTS2100 4100 Module US rev08.book Page xvi Jeudi, 1. août 2013 1:43 13
About This Guide
Recycling Information
User Manual 770000102/08 xvii
During off-hours, you can request assistance by doing one of the
following:
leave a voice mail message at the Technical Assistance number in
your region
e-mail North American Technical Assistance Center, tac@jdsu.com,
or European Technical Assistance Center, support[email protected]
submit your question using our online Technical Assistance Request
form at www.jdsu.com.
Recycling Information
JDSU recommends that customers dispose of their instruments and
peripherals in an environmentally sound manner. Potential methods
include reuse of parts or whole products and recycling of products
components, and/or materials.
Waste Electrical and electronic Equipment (WEEE) Directive
In the European Union, this label indicates that this product should not
be disposed of with household waste. Il should be deposited at an appro-
priate facility to enable recovery and recycling.
Conventions
This guide uses naming conventions and symbols, as described in the
following tables.
Table 2 Typographical conventions
Description Example
User interface actions appear in
this typeface.
On the Status bar, click Start.
Buttons or switches that you
press on a unit appear in this
TYPEFACE.
Press the ON switch
Code and output messages
appear in this typeface.
All results okay
MTS2100 4100 Module US rev08.book Page xvii Jeudi, 1. août 2013 1:43 13
About This Guide
Conventions
xviii
User Manual 770000102/08
Table 4 Symbol conventions
Text you must type exactly as
shown appears in this type-
face.
Type: a:\set.exe in the dia-
log box
Variables appear in this type-
face.
Type the new hostname.
Book references appear in this
typeface.
Refer to Newton’s Telecom
Dictionary
A vertical bar | means “or”: only
one option can appear in a sin-
gle command.
platform [a|b|e]
Square brackets [ ] indicate an
optional argument.
login [platform name]
Slanted brackets < > group
required arguments.
<password>
Table 3 Keyboard and menu conventions
Description Example
A plus sign + indicates simulta-
neous keystrokes.
Press Ctrl+s
A comma indicates consecutive
key strokes.
Press Alt+f,s
A slanted bracket indicates
choosing a submenu from
menu.
On the menu bar, click
Start > Program Files.
Table 2 Typographical conventions (Continued)
Description Example
This symbol represents a general hazard.
MTS2100 4100 Module US rev08.book Page xviii Jeudi, 1. août 2013 1:43 13
About This Guide
Conventions
User Manual 770000102/08 xix
Table 5 Safety definitions
This symbol represents a risk of electrical shock.
NOTE
This symbol represents a Note indicating related information or tip.
This symbol, located on the equipment or its packaging
indicates that the equipment must not be disposed of in a land-
fill site or as municipal waste, and should be disposed of
according to your national regulations.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
MTS2100 4100 Module US rev08.book Page xix Jeudi, 1. août 2013 1:43 13
About This Guide
Conventions
xx
User Manual 770000102/08
MTS2100 4100 Module US rev08.book Page xx Jeudi, 1. août 2013 1:43 13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182

JDS Uniphase 4100 User manual

Category
Measuring, testing & control
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI