Messoa NDF820PRO Quick start guide

Page is loading ...

Quick Start Guide

1

English

Safety Instructions

 Make sure the supplied voltage meets the power consumption

requirements of the camera before powering the camera on.

Incorrect voltage may cause damage to the camera.

 The camera should be protected from water and moisture, excessive

heat, direct sunlight and cold.

 This installation should be made by a qualied service person and

should conform to all local codes.

 Unplug the camera during lightening storms or when unused for

long periods of time.

Compliance

This equipment complies with the requirements as listed below:

 FCC Part 15 Class B

 CE: 2004/108/EC-Electromagnetic Compatibility (EMC) directive of

EN55022, EN61000-3-2, EN61000-3-3 and EN50130-4.

WEEE

Waste Electrical and Electronic Equipment

Correct disposal of this product (applicable in the European

Union and other European countries with separate collection

systems). This product should be disposed of, at the end of

its useful life, as per applicable local lows, regulations and

procedures.

2 Quick Start Guide

1. Introduction

1.1 Package Contents

 Indoor Dome Network Camera x1

 CD-ROM (User manual and IP Finder utility) x1

 Quick Start Guide x1

 Guide Pattern Sticker x1

 RJ-45 Female / Female Coupler x1

 Accessories

• Machine Type Flat Head Screw (#1) x4

• Tapping Type Flat Head Screw (#2) x4

• Plastic Anchor (#3) x4

• Rubber Foot (#4) x4

1

2

3 4

Quick Start Guide

3

English

1.2 Hardware Overview

Connectors

Model with xed lens

1

2

3

1. Power In (Red+/Black-): power connector, DC12V/AC24V

2. RJ-45 Ethernet Connector: network & PoE (Power over Ethernet)

connection

3. BNC: composite video output

Model with vari-focal lens

1

2

3

4

5

6

7

1.

Power In (Red+/Black-):

power connector, DC12V/AC24V

2.

RJ-45 Ethernet Connector:

network & PoE (Power over Ethernet)

connection

3.

BNC:

composite video output

4.

Audio Out (Green):

audio output

4 Quick Start Guide

5.

Audio In (Red):

audio input

6.

Alarm Out (Orange):

alarm signal output port

Reserved (Green)

RS-485 (Yellow)

7.

GND:

ground (electricity) in electrical circuits

Alarm In 1 (Red):

alarm signal input port

Alarm In 2 (Brown):

alarm signal input port

Quick Start Guide

5

English

2. Installation

2.1 Mounting the Camera

This camera is designed for ceiling & wall mounts depending on users

requirements. Mount the camera to your intended location.

Disassembling

1. Take off the dome cover screw.

2. Rotate the dome cover counterclockwise to unlock and pull free of

the housing.

3. Open (but not remove) the inner liner.

1. Dome Cover Screw

2. Dome Cover

3. Inner Liner

*Model with xed lens as illustration example

Drilling the Mounting Surface

1. Post the “Guide Pattern” sticker on the mounting surface.

2. Aiming the circles (the gure below marked with “+“ ) on the

sticker, drill four screw holes and one cable entry hole in the

ceiling/wall.

6 Quick Start Guide

Lens Direction

Note: Mounting surface material

determines screw type.

Refer to manual.

GUIDE PATTERN

Mounting the Camera

Example 1

1. Insert the plastic anchors into the screw holes (this gure take the

tapping type screws as the example to illustrate the mounting).

5. Dome Cover Screw

4. Dome Cover

3. Inner Liner

Guide Pattern Sricker

1. Plastic Anchors

2. Tapping Type Screws

2. Use the tapping screws to secure the camera base to the surface.

Quick Start Guide

7

English

Example 2

Use the machine screws to secure the camera base to the surface (this

gure take the machine type screws as the example to illustrate the

mounting).

5. Dome Cover Screw

4. Dome Cover

2. Inner Liner

3. microSD/SDHC Card

Guide Pattern Sricker

1. Machine Type

Screws

TipCautionWarning

Note

1. While you are securing the camera with the accompanying screws,

please be advised to hold the camera by its base. Do not hold the

lens or lens base with force that may deform the lens.

2. Use the machine type screws if you are attaching the camera to

a pendent mounting. Use the tapping type screws for all other

surfaces.

3. For cement surfaces, insert the “Plastic Anchors” into the holes. For

softer surfaces, do not use the “Plastic Anchors”.

4. Use the Rubber Feet for surface mounting.

8 Quick Start Guide

Adjusting Camera Angle

Check the monitored view by wiring the RCA jack to a monitor. With an

external monitor connected, you can adjust pan and tilt angles of the

camera for appropriate or better view.

RCA Jack for

Composite Video Output

Model with xed lens

RCA Jack for Composite

Video Output

Model with vari-focal lens

Pan Adjustment: Rotate the lens base to adjust the horizontal angle.

Tilt Adjustment: Tilt the lens base to adjust the vertical angle.

Quick Start Guide

9

English

Tilt Angle = 90 degrees

Pan Angle = about 355 degrees

Model with xed lens

Tilt Angle = 90 de-

grees

Pan Angle = about 355 de-

grees

Model with vari-focal lens

10 Quick Start Guide

Horizontal rotation: Rotate the dome base to adjust the horizontal

position. Do not turn the base more than 355° as this may cause the

internal cables to twist and disconnect or break.

Horizontal Rotation = 355 degrees

Model with xed lens

Horizontal Rotation = 355 degrees

Model with vari-focal lens

Quick Start Guide

11

English

TipCautionWarning

Note

When the tilt angle is less than 82/75 degrees, there is no distortion.

V=49.9° (Field of View)

82° Tilt Angle

Distortion

Area

Model with xed lens

75° Tilt Angle

Distortion

Area

24° Wide Angle (9mm)

68° Tele Angle (3mm)

Model with vari-focal lens

For model with vari-focal lens

Lens Adjustment: Loosen the screws to adjust the zoom control for

desired image view and adjust the focus for optimum picture sharpness.

Re-tighten the screws after nishing zoom/focus adjustments.

12 Quick Start Guide

Tele (T) & Wide (W)

Near(N) & Far(∞)

Assembling the Camera

Follow the steps below when all the camera adjustments and cabling

tasks are nished.

1. Close the inner liner.

2. For model with vari-focal lens: If you are to use a microSD/SDHC

card, remember to insert the card into the slot before assembling

the dome cover.

3. Assemble the dome cover.

4. Secure the dome cover with the accompanying screw.

2.2. Initial Conguration via a PC

Before connecting the camera to your network infrastructure, it’s

suggested that you connect the camera to a computer rst to perform

initial congurations.

1. Configure the computer’s IP address that must be on the

same network segment with the camera’s default IP address

(192.168.1.30 by default), such as:

• IP Address: 192.168.1.100

• Subnet Mask: 255.255.255.0

Quick Start Guide

13

English

2. Connect the RJ-45 cable of the camera to the computer.

The LAN port of the camera supports auto MDI/MDIX so there is no

need to use a cross-over cable.

3. To make sure the connection between the camera and the

computer is successful established, you can attempt to ping the

camera from your computer.

• First click the Start menu and select Programs. Then select

Accessories.

• Choose Command Prompt. Click OK.

• Type ping x.x.x.x, where x.x.x.x is the IP address of the

camera (default is 192.168.1.30). If the message of “Reply

from…” appears, it means the connection is done.

4. On the PC, launch a web browser and enter the IP address of the

camera in the URL eld:

http://192.168.1.30/

5. When prompted for login, respectively enter the default user name:

admin and password: 1234 to log in. Note that the user name and

password are case-sensitive.

6. Configure the settings to meet your requirements. For more

information, refer to the User Manual on the provided CD-ROM.

14 Quick Start Guide

2.3 Connecting to Your Network

Connecting to a LAN

If you have multiple cameras installed on your network, you can

use the provided IP Finder utility to manage the cameras. For more

information, refer to the User Manual on the provided CD-ROM.

Router/Switch/Hub

Connecting to the Internet

Router

xDSL/Cable

Modem

To enable remote access to the cameras, you must configure your

router/rewall to open port numbers. For more information, refer to the

User Manual on the provided CD-ROM.

Page is loading ...

Guia de inicio rápido

3

Español

1.2 Presentación del Hardware

Conectores

Modelo con lente ja

1

2

3

1. Entrada de la fuente de alimentación (Rojo +/Negro -):

Conector eléctrico, CC 12V / CA 24V

2. RJ-45 (Ethernet/PoE): Conexión de red y PoE (Power over

Ethernet)

3. BNC: Salida de vídeo compuesto

Modelo con lente varifocal

1

2

3

4

5

6

7

1.

Power In (Red+/Black-):

power connector, DC12V/AC24V

2.

RJ-45 Ethernet Connector:

network & PoE (Power over Ethernet)

connection

3.

BNC:

composite video output

4 Guia de inicio rápido

4.

Audio Out (Green):

audio output

5.

Audio In (Red):

audio input

6.

Alarm Out (Orange):

alarm signal output port

Reserved (Green)

RS-485 (Yellow)

7.

GND:

ground (electricity) in electrical circuits

Alarm In 1 (Red):

alarm signal input port

Alarm In 2 (Brown):

alarm signal input port

Page is loading ...

6 快速安裝指南

Lens Direction

Note: Mounting surface material

determines screw type.

Refer to manual.

GUIDE PATTERN

安裝攝影機

範例 1

1. 先將塑料錨插入螺絲孔中（下圖以自攻螺絲類型示範安裝）。

2. 平頭自攻螺絲

3. 內襯機殼

4. 球型外罩

1. 塑料錨

定位貼紙

5. 球型外罩螺絲

2. 再用自攻螺絲將攝影機底座固定於安裝面上。

Page is loading ...

Messoa NDF820PRO Quick start guide

This manual is also suitable for

Messoa NDF820PRO Quick start guide

in other languages

Related papers

Other documents