EZ-FLO 10713 Installation guide

Brand: EZ-FLO

Model: 10713

Type: Installation guide

This manual is also suitable for

10715

Dual Control

Bathroom Faucet

Before You Begin

Check to make sure you have the following:

10713

10715

Tools and Supplies

You will need the following to install your new faucet:

Pipe

Tape

Adjustable

Wrench

With Pop-Up

Phillips

Screwdriver

This product is engineered to meet the EPA

WaterSense flow requirement. The flow rate

is governed by the aerator. If replacement is

ever required, be sure to replace it with a

WaterSense compliant lavatory faucet aerator

to retain the water conserving faucets of this

faucet.

Silicone

Sealant

Shut off main water supply before installation.

Faucet Installation

2 Remove assembled

parts from the faucet body.

8 After installing faucet, remove

aerator and turn on water to remove

any left over debris. Reassemble

aerator and tigthen.

3 Place the spout in the

center hole of sink. Secure

parts as shown above.

4 Remove assembled

parts from the faucet

body.

7 Apply pipe tape onto the threads

of the handle valve body inlet port,

connect supply tube and tighten with

lock nut.

5 Place the handle bodies through the

left and right holes. Re-assemble the

parts and tighten mounting nut.

6 Remove protective cap.Connect handle assembly to the spout body with

water supply hose. Push supply hose adapter with hose coupling until you

hear a "click". Pull hose down to make sure connected firmly.

1 Shut off water supply.

5 Insert plunger. Insert ball rod into

drain assembly.

NOTE: Plastic loop on plunger facing

rear of sink is in locked mode and

plunger cannot be removed. Plastic

loop on plunger facing the front of sink

is in unlocked mode and can be

removed for easy cleaning.

6 Insert lift rod through faucet and

attach lift rod strap to lift rod. Push

button to allow lift rod to slide

through. Release to lock.

7 Push down the ball rod so that

the drain is at “open position”.

Rotate the connector on the strap to

the proper height to connect to the

ball rod when it is at “open position”.

2 Remove plunger. Install drain

hole set.

3 Attach rubber washer onto the

thread of drain hole set and

tighten lock nut.

4 Attach drain assembly.

Pop-Up Drain Installation

Washer

Drain hole set

Lift rod

Main plunger

Lift rod strap

Large rubber washer

Drain assembly

Ball rod

Lock nut

Loop toward

front of sink

Drain

Loop toward

rear of sink

Drain

1 Remove old pop-up drain

assembly.

1 Metal Handle Assembly A66E861

2.1 Handle Extension Assembly - Cold A66G378C

2.2 Handle Extension Assembly - Hot A66G378H

3 Retainer Nut A016022

4.1 Ceramic Disc Cartridge - Cold A507104N

4.2 Ceramic Disc Cartridge - Hot A507103N

5 Lock Nut A009387CP

6 Handle Trim Ring A66F620

7 Mounting Hardware Assembly A66D900ZN-H

8 Mounting Hardware A66D455

9 Supply Hose A135141N

10 Aerator 1.2 gpm A553058N

11 Lift Rod A025608

12 50/50 Pop-up Assembly A525371

Keep this manual for ordering replacement parts.

Replacement Parts

Troubleshooting Guide

Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and

close stopper or drain to avoid losing small parts.

noituloSesuaCmelborP

Leak from spout Damaged or dirty seals Disassemble faucet, remove cartridge. Clean or replace

cartridge if necessary. Reassemble.

Leak from under handle Damaged cartridge Remove handle. Replace cartridge.

Uneven water spray Clogged aerator Remove aerator. Clean or replace aerator if necessary.

Leak from around aerator Bad aerator seal Remove aerator. Check to see that seal is flat and undamaged.

Replace aerator if necessary.

Water drains slowly or not at all Clogged drain Remove stopper. Remove visible debris.

If still clogged, remove and clean trap. Reassemble.

2.1

2.2

4.1

4.2

11.

12.

10.

EZ-FLO 10713 Installation guide

Brand: EZ-FLO

Model: 10713

Type: Installation guide

This manual is also suitable for

10715

Download PDF

report

EZ-FLO 10713 Installation guide

This manual is also suitable for

EZ-FLO 10713 Installation guide

Related papers

Other documents