DeckoRail 237300 Installation guide

Brand: DeckoRail

Model: 237300

Type: Installation guide

Pressure-Treated Stair Railing with Aluminum Balusters

INSTALLATION INSTRUCTIONS

ITEMS YOU WILL NEED

• Drill/power screwdriver

• Miter or circular saw with carbide tip blade

• Tape measure

• Carpenter’s level

• Carpenter’s pencil

• Safety glasses/goggles

• Gloves

Step 1: Measure the distance between posts and, if necessary,

cut the 2x4 rails to size by trimming the unnotched end. The bal-

uster and rails have been set to 34 degrees, so if you need to cut

the rails and cap rail, cut them to the 34 degree angle (fig.2 ). Cut

the cap rail at the same end as the rails.

Planning your project: The stair railing was designed

to work on stairs that have a 10” run and 6-3/4” rise,

which creates a 34-degree angle. Check local building code

requirements prior to starting your project. A 6” ball cannot

pass through the triangle formed by the bottom rail, tread

and riser. Stair rails are commonly required to be more than

34” and less than 38” from the tread nose to the top of the

rail (fig. 1).

Railing Brackets (4)

Baluster

Outside Edge of Stairs

Post

Cap

Less than 6"

Less than 4"

Support Block

34" < Tread Nose to

Top of Rail < 38"

Top and

Bottom Rail

•

StairsOutline3a1.ai

g. 1

Cut This End

Do NOT Cut This End

Notch

StairRail1.ai

34°

g. 2

This brochure is for illustration purposes only. Use of this product must be in accordance with all local zoning and/or building codes. Consumer assumes all risks and liability associated with the use of this

product. For details on safe handling and warranty information, go to UFPI.com/ptinfo.

50415 Herbert Street, P.O. Box 129, Granger, IN 46530

574.277.7670

www.ufpi.com

7188 Stair_7/13

Cap

123 456789101112131415

StairRail2.ai

Insert Rail

•

g. 3

Bottom Rail

Railing Brackets

Balusters

Cap Rail

•

StairRail3.ai

g. 4

Step 2: Place the moulded cap rail upside down on a ﬂat surface.

Next, place the top 2x4 rail with the notch on the same side as the

baluster holes into the moulded cap rail channel so that the holes

are facing up. Starting from either end, fasten the rails together

using the (7) 4” screws through holes 1, 2, 5, 8, 11, 14, 15. If rails are

trimmed, predrill any additional holes with a 1/8” drill bit and insert

the screw into the next nearest hole (fig. 3).

Step 3: Attach the (4) 2x4 DeckoRail railing brackets according to

the included instructions.

Step 4: Attach the bottom 2x4 rail, with the holes facing up, using

the 2x4 DeckoRail railing brackets. Insert the balusters into the pre-

drilled holes (fig. 4).

Step 5: Attach the cap rail by aligning the holes to the baluster

at one end of the rail and working your way to the opposite end,

ensuring that all of the balusters are secured between the two rails

(fig. 4).

Step 6: Fasten a support block at the center of the bottom rail to

the deck surface for spans greater than three feet (fig. 1).

Page is loading ...

Cette brochure est à titre d’illustration uniquement. Toute utilisation de ce produit doit être conforme aux codes locaux de zonage et/ou du bâtiment. Le consommateur assume tous les risques et respon-

sabilités associés à l’utilisation de ce produit. Pour tous les détails sur le maniement prudent et les informations sur la garantie, rendez-vous sur UFPI.com/ptinfo.

50415 Herbert Street, P.O. Box 129, Granger, IN 46530

574.277.7670

www.ufpi.com

7188 Stair_FR_7/13

rampe supérieure