Dacor EF36BNFSS User manual

Type
User manual

This manual is also suitable for

Dacor EF36BNFSS is a refrigerator model that comes with a Preference™ Handle Kit. The kit includes three handles (two large and one small) that can be installed on the refrigerator to customize its look. The handles are easy to install and can be tightened using a 3/32” Allen wrench. The refrigerator also has six handle mounting studs that are used to attach the handles. To install the handles, simply slide them over the mounting studs and tighten the set screws. The handles can be adjusted to different positions to ensure a comfortable grip.

Dacor EF36BNFSS is a refrigerator model that comes with a Preference™ Handle Kit. The kit includes three handles (two large and one small) that can be installed on the refrigerator to customize its look. The handles are easy to install and can be tightened using a 3/32” Allen wrench. The refrigerator also has six handle mounting studs that are used to attach the handles. To install the handles, simply slide them over the mounting studs and tighten the set screws. The handles can be adjusted to different positions to ensure a comfortable grip.

INSTALLATION
INSTRUCTIONS
Preference Handle Kit,
PN AFP36H3
REFRIGERATOR MODELS: EF36BNFSS & PF36BNDFXX*
*Where XX indicates color
Installation Preparation (Model EF36BNFXX Only.
For Model PF36BNDFXX, skip to Step 3):
STEP 1: Using a T20 Torx driver, remove the six (6)
handle mounting studs from the front of the
refrigerator. Retain the Torx mounting screws.
Discard the studs.
Handle Mounting
Stud Locations
Existing handle
mounting screw
(keep)
Existing mounting
stud (discard)
Part No. 102864 Rev. C
Parts Included
Preference Style Handles (2 Large, 1 Small)
Tools Required
3/32” Allen wrench (not supplied)•
T20 Torx driver (EF36BNFSS Only)•
Page 2
Refrigerator Handle Kit Installation Instructions
STEP 2 (Model EF36BNFSS only):
Using the T20 Torx driver and the screws removed in step 1, install the six (6) short
mounting studs from the kit in the locations shown.
Handle Mounting
Stud Locations
New mounting
stud from kit
Existing handle
mounting screw
Handle Mounting
Studs
Set Screw Holes
Bottom (Freezer) Handle Installation
STEP 3: Find the smallest of the three handles in the
kit box.
STEP 4: Mount the handle to the bottom drawer by
sliding the holes on the back over the handle
mounting studs on the refrigerator. Make sure
the set screw holes on the handle are facing
toward the bottom. You may need to loosen
the set screws using a 3/32” Allen wrench to
allow the handle to slide into place.
STEP 5: Carefully tighten the set screws into place us-
ing the 3/32” Allen wrench. Be careful not to
scratchthenish.
STEP 6: Checktomakesurethehandleisrmly
attached.
Refrigerator Handle Kit Installation Instructions
Page 3
Top Right Handle Installation
STEP 7: Mount the handle to the right door by slid-
ing the holes on the back over the handle
mounting studs on the right door. Make sure
the set screw holes face toward the center
of the refrigerator. Loosen the set screws if
necessary to allow the handle to slide into
place.
STEP 8: Carefully tighten the set screws into place
using the 3/32” Allen wrench. Be careful not
toscratchthenish.
STEP 9: Checktomakesurethehandleisrmlyat-
tached.
Top Left Handle Installation
STEP 10: Mount the remaining handle to the left door
with set screw holes toward the center of the
refrigerator. Loosen the set screws if neces-
sary to allow the handle to slide into place.
STEP 11: Open the left door while holding the handle
in place to prevent damage to the other
handle during step 12.
STEP 12: Carefully tighten the set screws into place
using the 3/32” Allen wrench. Be careful not
toscratchthenish.
STEP 13: Checktomakesurethehandleisrmly
attached.
Handle Mounting
Studs
Set Screw
Holes
Handle Mounting
Stud
Handle Mounting
Stud
Set Screw
Hole
Set Screw
Hole
Dacor●1440BridgeGateDrive,DiamondBar,CA91765●Tel:(800)793-0093●FAX:(626)403-3130●www.Dacor.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dacor EF36BNFSS User manual

Type
User manual
This manual is also suitable for

Dacor EF36BNFSS is a refrigerator model that comes with a Preference™ Handle Kit. The kit includes three handles (two large and one small) that can be installed on the refrigerator to customize its look. The handles are easy to install and can be tightened using a 3/32” Allen wrench. The refrigerator also has six handle mounting studs that are used to attach the handles. To install the handles, simply slide them over the mounting studs and tighten the set screws. The handles can be adjusted to different positions to ensure a comfortable grip.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI