Dacor EF36BNDFSS Installation guide

Category
Fridges
Type
Installation guide
REFRIGERATOR MODEL EF36BNDFSS
I
The Life of the Kitchen. _
I
Epicure ®Handle Service Kit,
PN 700976
I INSTALLATIONINSTRUCTIONS I
Tools Required
3/32" Allen wrench (not supplied)
T20 Torx driver
Parts Included
Handle Set Screws
(6 each - PN 102984)
T-20 Mounting Screws
(6 each - PN 104170)
Size may vary
from that shown
Size may vary
from that shown
Handle Mounting Studs
(6 each - PN 102987)
Handle End Caps - Right Side
(PN 102866-01)
Handle End Caps - Left Side
(PN 102866-02)
v'
Handle Set Scr_
Locations
I
Part No. 104169 Rev. A-1
Refrigerator Handle Service Kit Instructions
STEP 3:
STEP 4:
STEP 5:
Slide the existing end caps off of one of the
handles removed in step 2. Discard the old
end caps.
Slide two (2) of the new end caps from the kit
onto the ends of the handle.
IMPORTANT: On each handle, the set screw
holes must be on the same side as shown. If
the set screw holes are on opposite sides of
the handle, remove one of the end caps, find
one from the kit that has the hole on the oppo-
site side and install it.
Repeat step 4 for the remaining handles.
Assembling New __
End__
Set screw holes
on same side.
STEP 6:
STEP 7:
Using a Phillips head screwdriver, remove the
six (6) handle mounting studs from the front of
the refrigerator.
Discard the all of the studs and screws re-
moved in step 6.
Existing handle
mounting screw
(discard)
O / ®
Existing mounting
stud (discard)
@
@
@
Handle Mounting
Stud Locations
Page 2
Refrigerator Handle Service Kit Instructions
STEP 8:
Using a T20 Torx driver and the Torx screws from
the kit, install the six (6) handle mounting studs
from the kit in the locations shown.
J
\
New handle
mounting screw
New mounting
stud from kit
@
@
@
Handle Mounting
Stud Locations
STEP 9:
STEP 10:
STEP 11:
STEP 12:
STEP 13:
Locate the smallest of the three handles as-
sembled in step 4.
Insert two (2) of the provided set screws into
the holes on the handle end caps. Thread
about two or three turns.
Mount the handle to the bottom drawer by
sliding the holes on the back over the handle
mounting studs on the refrigerator. Make sure
the set screw holes face the floor.
Carefully tighten the set screws into place
using a 3/32" Allen wrench. Be careful not to
scratch the finish.
Check to make sure that the handle is firmly
attached.
Handle Mounting
Studs
I
Set Screws
Page 3
Refrigerator Handle Kit Installation Instructions
STEP 14:
STEP 15:
STEP 16:
STEP 17:
Insert two (2) of the provided set screws into the
holes on the end caps of one of the remaining
handle assemblies. Thread about two or three
turns.
Mount the handle to the top right door by sliding
the holes on the back over the handle mounting
studs on the door. Make sure the set screw holes
face the center of the refrigerator.
Carefully tighten the set screws into place using a
3/32" Allen wrench. Be careful not to scratch the
finish.
Check to make sure that the handle is firmly at-
tached.
S Handle Mounting
S Studs
p
STEP 18:
STEP 19:
STEP 20:
STEP 21"
STEP 22:
Insert the remaining set screws into the holes
on the side of the remaining handle. Thread
about two or three turns.
Mount the remaining handle to the top left door
with the holes for the set screws toward the
center of the refrigerator.
Open the left door while holding the handle in
place to prevent damage to the other handle
during step 21.
Carefully tighten the set screws into place
using a 3/32" Allen wrench. Be careful not to
scratch the finish.
Check to make sure that the handle is firmly
attached.
Handle Mounting
Stud
Set
Screw
Set
Screw
Handle Mounting
Stud
The Life of the Kitchen?
Dacor 1440 Bridge Gate Drive, Diamond Bar, CA 91765 Tel: (800) 793-0093 FAX: (626)403-3130 www.Dacor.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dacor EF36BNDFSS Installation guide

Category
Fridges
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI