3com 4800G PWR Getting Started Manual

www.3Com.com

Part Number: 10016617 Rev AA

Published: April 2008

3Com

®

Switch 4800G Family

Getting Started Guide

Switch 4800G 24-Port

Switch 4800G PWR 24-Port

Switch 4800G 48-Port

Switch 4800G PWR 48-Port

Switch 4800G 24-Port SFP

3Com Corporation

350 Campus Drive

Marlborough, MA

USA 01752-3064

form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without

written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time

without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or

expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality,

and fitness for a particular purpose. 3Com may make improvements or changes in the product(s) and/or the program(s)

described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license agreement

included with the product as a separate document, in the hard copy documentation, or on the removable media in a

directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will

be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are provided to

you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense. Software is

delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item”

as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Com’s standard commercial

license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or

FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided

on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered

in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

Cisco is a registered trademark of Cisco Systems, Inc.

Funk RADIUS is a registered trademark of Funk Software, Inc.

Aegis is a registered trademark of Aegis Group PLC.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and Windows NT are

registered trademarks of Microsoft Corporation. Novell and NetWare are registered trademarks of Novell, Inc. UNIX is a

registered trademark in the United States and other countries, licensed exclusively through X/Open Company, Ltd.

IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Inc.

All other company and product names may be trademarks of the respective companies with which they are associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations. To uphold our policy, we are committed

to:

Establishing environmental performance standards that comply with national legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to recognized environmental standards.

Maximizing the recyclable and reusable content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

CONTENTS

ABOUT THIS GUIDE

Conventions 5

Related Documentation 5

1 PRODUCT OVERVIEW

Introduction 7

Switch 4800G 24-Port 8

Switch 4800G PWR 48-Port 11

Switch 4800G PWR 24-Port 13

Switch 4800G 24-Port SFP 17

Switch 4800G 48-Port 18

System Specifications of the Switch 4800G Series 22

Pluggable Modules 22

Optional Interface Modules 23

CX4 Cable 24

2 PREPARATING TO INSTALL THE SWITCH

Safety Precautions 25

Installation Site 25

Installation Tools 27

3 INSTALLING THE SWITCH

Installing the Switch into a 19-Inch Cabinet 29

Mounting the Switch on a Workbench 38

Connecting the Power Cables and the Grounding Cable 38

Connecting the Console Cable 46

Installing and Removing Optional Interface Modules 47

Installing and Removing the Dedicated CX4 Cable 50

Verifying the Installation 51

4 INITIAL POWER-ON

Setting Up the Configuration Environment 53

Connecting the Console Cable 53

Setting Terminal Parameters 53

Booting the Switch 57

5 LOADING THE BOOT ROM AND HOST SOFTWARE

Introduction to Loading Modes 61

Local Software Loading 61

Remote Software Loading 70

6 MAINTENANCE AND TROUBLESHOOTING

Software Loading Failure 73

Password Loss 73

Power Supply Failure 74

Configuration System Failure 74

A LIGHTNING PROTECTION FOR THE SWITCH

Installating the Lightning Arrester for AC Power (Socket Strip with Lightning

Protection) 75

Installation of Lightning Arrester for Network Port 76

B 3COM NETWORK MANAGEMENT

3Com Network Supervisor 79

3Com Network Director 79

3Com Network Access Manager 80

3Com Enterprise Management Suite 81

Integration Kit with HP OpenView Network Node Manager 81

ABOUT THIS GUIDE

This guide describes the 3Com

®

Switch 4800G and how to install hardware,

configure and boot software, and maintain software and hardware. This guide

also provides troubleshooting and support information for your switch.

This guide is intended for Qualified Service personnel who are responsible for

configuring, using, and managing the switches. It assumes a working knowledge

of local area network (LAN) operations and familiarity with communication

protocols that are used to interconnect LANs.

n

Always download the Release Notes for your product from the 3Com World Wide

Web site and check for the latest updates to software and product

documentation:

http://www.3com.com

Conventions Table 1 lists icon conventions that are used throughout this guide.

The following manuals offer additional information necessary for managing your

Switch Switch 4800G:

■ Switch 4800G Command Reference Guide — Provides detailed descriptions of

command line interface (CLI) commands, that you require to manage your

Switch 4800G.

■ Switch 4800G Configuration Guide— Describes how to configure your Switch

4800G using the supported protocols and CLI commands.

■ Switch 4800G Quick Reference Guides — Provides a summary of command

line interface (CLI) commands that are required for you to manage your Switch

4800G.

Table 1 Notice Icons

Icon Notice Type Description

n

Information note Information that describes important features or

instructions.

c

Caution Information that alerts you to potential loss of data

or potential damage to an application, system, or

device.

w

Warning Information that alerts you to potential personal

injury.

6 ABOUT THIS GUIDE

■ Switch 4800G Release Notes — Contains the latest information about your

product. If information in this guide differs from information in the release

notes, use the information in the Release Notes.

These documents are available in Adobe Acrobat Reader Portable Document

Format (PDF) on the CD-ROM that accompanies your router or on the 3Com

World Wide Web site:

http://www.3com.com/

1

PRODUCT OVERVIEW

Introduction 3Com Switch 4800G Family (hereinafter referred to as the Switch 4800G) are

Gigabit Ethernet switching products developed by Hangzhou 3Com Technologies

Co., Ltd. (hereinafter referred to as 3Com). The Switch 4800G support diversified

service features, IPv6 forwarding, and routing function, and provide 10GE

extended module slots. Through the 3Com proprietary cluster management, you

can streamline network management. The Switch 4800G are designed to operate

at the convergence or access layer of enterprise networks and metropolitan area

networks (MANs). The Switch 4800G support the IPv4/IPv6 dual stack and can also

be used for connecting server groups in data centers.

Table 2 lists the models of the Switch 4800G.

Together with an auto-sensing 10/100/1000BASE-T Ethernet port, each

1000Base-X SFP port forms a Combo port. For each Combo port, either the SFP

port or the auto-sensing 10/100/1000BASE-T Ethernet port can be used at a time.

For the mapping between the two ports forming a Combo port, refer to Table 3.

Table 2 Models of the Switch 4800G

Model

Number of auto-sensing

10/100/1000Base-T

Ethernet ports

Number of

1000Base-X SFP

ports

Number of

console

ports

Switch 4800G 24-Port 24 4 1

Switch 4800G PWR 48-Port 48 4

Switch 4800G PWR 24-Port 24 4

Switch 4800G 24-Port SFP 48 4

Switch 4800G 48-Port 8 24

Table 3 Mapping between two ports forming a Combo port

Model

1000Base-X SFP port

number

Auto-sensing 10/100/1000Base-T

Ethernet port number

Switch 4800G 24-Port

Switch 4800G PWR

24-Port

25 22

26 24

27 21

28 23

Switch 4800G PWR

48-Port Switch 4800G

24-Port SFP

49 46

50 48

51 45

52 47

8 CHAPTER 1: PRODUCT OVERVIEW

For the convenience of monitoring the running of the Switch 4800G, LEDs are also

equipped on their front panel.

Switch 4800G 24-Port

Appearance The Switch 4800G 24-Port provides twenty-four auto-sensing 10/100/1000BASE-T

Ethernet ports, four 1000Base-X SFP ports, and one console port on the front

panel, and one AC power socket, one redundant power system (RPS) port, and

two extended module slots on the rear panel. Figure 2 shows the appearance of

the Switch 4800G 24-Port.

Figure 1 Appearance of the Switch 4800G 24-Port

Front Panel Figure 2 Front panel of the Switch 4800G 24-Port

Switch 4800G 48-Port 25 17

26 18

27 19

28 20

29 21

30 22

31 23

32 24

Tabl e 3 Mapping between two ports forming a Combo port

Model

1000Base-X SFP port

number

Auto-sensing 10/100/1000Base-T

Ethernet port number

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) SFP port status LEDs

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

Switch 4800G 24-Port 9

Rear Panel Figure 3 Rear panel of the Switch 4800G 24-Port

Power Supply System The Switch 4800G 24-Port can adopt AC input, or 12 V RPS input, or both to

provide backup. Only the recommended RPS can be used.

■ AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

■ RPS input

Rated voltage range: 10.8 VDC to 13.2 VDC

Cooling System The Switch 4800G 24-Port is equipped with four fans for heat dissipation.

LEDs For descriptions about LEDs, see Table 4. You can switch the Mode LED display

mode between speed and duplex by pressing the Mode button on the panel.

(3) Console port (4) 7-segment digital LED

(5) Power LED (6) RPS LED

(7) LED for extended module slot 1 (8) LED for extended module slot 2

(9) Mode LED (10) Mode button

(1) AC power socket (2) RPS port

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

(1) (2)

(3)

(4)

(5)

(1) (2)

(3)

(4)

(5)

Table 4 LEDs on the front panel of the Switch 4800G 24-Port

LED Mark Status Description

Mode LED Mode Speed Solid green Rate of the port

Duplex Solid yellow Duplex mode of the port

Power LED PWR Solid green The switch is started normally.

Flashing green (1 Hz) The system is running a power-on

self-test (POST).

Solid red The system fails the POST or a power

failure occurs.

Flashing yellow (1 Hz) Some ports fail a POST or a port

failure occurs.

OFF The power is disconnected.

10 CHAPTER 1: PRODUCT OVERVIEW

Redundant power

system LED

RPS Solid green The AC power supply is normal and

the RPS is connected and works

normally.

Solid yellow The RPS input is normal, but an AC

input failure occurs or no AC power

is connected.

OFF No RPS is connected.

Module LED MOD Solid green The module is in position and works

normally.

Flashing yellow The switch does not support the

module or a module failure occurs.

OFF No module is installed.

7-segment digital LED Unit POST running The power LED flashes green The LED displays the POST test ID.

POST failed The power LED flashes red The LED flashes the POST test ID of

the failed test.

Software loading The power LED flashes green. A bar rotates clockwise around the

LED.

Fan failure The power LED is solid red. The LED displays F.

Over-temperature alarm The power LED is solid red. The LED displays t.

Cluster state The power LED is solid green. For a command switch, the LED

displays C.

For a member switch, the LED

displays S.

For a candidate switch, the LED

displays c.

The LED displays 1 if there is only one

unit.

Table 4 LEDs on the front panel of the Switch 4800G 24-Port

LED Mark Status Description

Switch 4800G PWR 48-Port 11

Switch 4800G PWR

48-Port

Appearance The Switch 4800G PWR 48-Port provides forty-eight auto-sensing

10/100/1000BASE-T Ethernet ports, four 1000Base-X SFP ports, and one console

port on the front panel, and one AC power socket, one RPS port, and two

extended module slots on the rear panel. Figure 5 shows the appearance of the

Switch 4800G PWR 48-Port.

10/100/1000Base-T

port status LED

- Speed Green A 1000 Mbps link is present. When

data is being received or sent, the

LED flashes at a high frequency.

Yellow A 10/100 Mbps link is present. When

data is being received or sent, the

LED flashes at a high frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

Duplex Green The port works in the full duplex

mode. The LED flashes at a high

frequency when data is being

received or sent.

Yellow The port works in the half duplex

mode. The LED flashes at a high

frequency when data is being

received or sent

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

SFP port status LED

(1000 Mbps)

- The Mode button has no

effect on the LED.

Green A 1000 Mbps link is present. When

data is being received or sent, the

LED flashes at a high frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

SFP port status LED

(100 Mbps)

- Speed Yellow A 100 Mbps link is present. When

data is being received or sent, the

LED flashes at a high frequency.

Flashing yellow (3 Hz) The port failed the POST.

OFF No link is present.

Duplex Green The port operates in the full duplex

mode. When data is being received

or sent, the LED flashes at a high

frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

Table 4 LEDs on the front panel of the Switch 4800G 24-Port

LED Mark Status Description

12 CHAPTER 1: PRODUCT OVERVIEW

Figure 4 Appearance of the Switch 4800G PWR 48-Port

Front Panel Figure 5 Front panel of the Switch 4800G PWR 48-Port

Rear Panel Figure 6 Rear panel of the Switch 4800G PWR 48-Port

Power Supply System The Switch 4800G PWR 48-Port can adopt AC input, or 12V RPS input, or both to

provide backup. Only the recommended RPS can be used.

■ AC power input

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) Console port (3) 7-segment digital LED

(4) Mode button (5) Mode LED

(6) Power LED (7) RPS LED

(8) LED for extended module slot 1 (9) LED for extended module slot 2

(10) SFP port status LED

(1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5) (1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5)

(1) AC power socket (2) RPS port

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

(1)

(2)

(3)

(4)

(5)

(1)

(2)

(3)

(4)

(5)

Switch 4800G PWR 24-Port 13

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

■ RPS input

Rated voltage range: 10.8 VDC to 13.2 VDC

Cooling System The Switch 4800G PWR 48-Port is equipped with four fans for heat dissipation.

LEDs The LEDs on the front panel of the Switch 4800G PWR 48-Port are the same as

those of the Switch 4800G 24-Port. For details, see Table 4.

Switch 4800G PWR

24-Port

Appearance The Switch 4800G PWR 24-Port provides twenty-four auto-sensing

10/100/1000Base-T Ethernet ports, four 1000Base-X SFP ports, one console port

on the front panel, and one AC power socket, one RPS port, and two extended

module slots on the rear panel. Figure 7 shows the appearance of the Switch

4800G PWR 24-Port.

Figure 7 Appearance of the Switch 4800G PWR 24-Port

Front Panel Figure 8 Front panel of the Switch 4800G PWR 24-Port

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) SFP port status LED

(3) Console port (4) 7-segment digital LED

(5) Power LED (6) RPS LED

(1)

(2) (3) (4) (5) (6) (7) (8 )

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8 )

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8 )

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8 )

(9)

(10)

14 CHAPTER 1: PRODUCT OVERVIEW

Rear Panel Figure 9 Rear panel of the Switch 4800G PWR 24-Port

Power Supply System The Switch 4800G PWR 24-Port can adopt AC power input, or DC power input, or

both to provide backup.

■ AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Rated voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Only the RPS recommended by 3Com can be used for the Switch 4800G PWR

24-Port. The -48 VDC power supply in the equipment room cannot be used

directly. Otherwise, the device may be damaged.

■ DC power input

Rated voltage range: -52 VDC to -55 VDC

Cooling System The Switch 4800G PWR 24-Port is equipped with six fans for heat dissipation.

LEDs For descriptions about LEDs, see Table 5. You can switch the Mode LED display

mode between speed, duplex, and PoE by pressing the Mode button on the panel.

(7) LED for extended module slot 1 (8) LED for extended module slot 2

(9) Mode LED (10) Mode button

(1) RPS port (2) AC power socket

(3) Grounding screw (4) Extended interface module slot 1

(5) Extended module slot 2

(1) (2)

(3)

(4)

(5)

(1) (2)

(3)

(4)

(5)

Table 5 Descriptions of the LEDs on the front panel of Switch 4800G PWR 24-Port

LED Mark Status Description

Mode LED Mode Speed Solid green Rate of the port

Duplex Solid yellow Duplex mode of the port

PoE Flashing green (1 Hz) PoE mode of the port

Power LED PWR Solid green The switch is started normally.

Flashing green (1 Hz) The system is running a power-on self-test

(POST).

Solid red The system fails the POST or a power

failure occurs.

Flashing yellow (1 Hz) Some ports fail a POST or a port failure

occurs.

OFF The power is disconnected.

Switch 4800G PWR 24-Port 15

Redundant power

system LED

RPS Solid green The AC power input and the DC power

input are both normal.

Solid yellow The DC power input is normal, but an AC

power failure occurs or no AC power is

connected.

OFF No DC power is connected.

Module LED MOD Solid green The module is in position and works

normally.

Flashing yellow The switch does not support the module

or a module failure occurs.

OFF No module is installed.

7-segment digital

LED

Unit POST running The power LED flashes green The LED displays the POST test ID.

POST failed The power LED flashes red The LED flashes the POST test ID of the

failed test.

Software loading The power LED flashes green. A bar rotates clockwise around the LED.

Fan failure The power LED is solid red. The LED displays F.

Over-temperature alarm The power LED is solid red. The LED displays t.

Cluster state The power LED is solid green. For a command switch, the LED displays C.

For a member switch, the LED displays S.

For a candidate switch, the LED displays c.

The LED displays 1 if there is only one unit.

PoE mode The power LED is solid green. The LED displays the utilization of the

power supply.

Table 5 Descriptions of the LEDs on the front panel of Switch 4800G PWR 24-Port

LED Mark Status Description

0 - 20%

21 - 40%

41 - 60%

61 - 80%

81 - 100%

16 CHAPTER 1: PRODUCT OVERVIEW

10/100/1000Base-T

Ethernet port status

LED

- Speed Green A 1000 Mbps link is present. When data is

being received or sent, the LED flashes at a

high frequency.

Yellow A 10/100 Mbps link is present. When data

is being received or sent, the LED flashes at

a high frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

Duplex Green The port works in the full duplex mode.

The LED flashes at a high frequency when

data is being received or sent.

Yellow The port works in the half duplex mode.

The LED flashes at a high frequency when

data is being received or sent

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

PoE Solid green The port supplies power normally.

Flashing green (1 Hz) The required power of the attached device

exceeds the maximum power that the port

can supply.

The total power reaches the maximum

power, so the port stops supplying power.

Solid yellow The device attached to the port is not a

powered device (PD), so the port cannot

supply power.

A PoE failure occurs, so the port cannot

supply power.

Flashing yellow (3 Hz) The port fails the POST.

OFF The port does not supply power.

SFP port status LED

(1000 Mbps)

- The Mode button has no

effect on the LED.

Green A 1000 Mbps link is present. When data is

being received or sent, the LED flashes at a

high frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

SFP port status LED

(100 Mbps)

- Speed Yellow A 100 Mbps link is present. When data is

being received or sent, the LED flashes at a

high frequency.

Flashing yellow (3 Hz) The port failed the POST.

OFF No link is present.

Duplex Green The port operates in the full duplex mode.

When data is being received or sent, the

LED flashes at a high frequency.

Flashing yellow (3 Hz) The port fails the POST.

OFF No link is present.

Table 5 Descriptions of the LEDs on the front panel of Switch 4800G PWR 24-Port

LED Mark Status Description

Switch 4800G 24-Port SFP 17

Switch 4800G 24-Port

SFP

Appearance The Switch 4800G 24-Port SFP provides forty-eight auto-sensing

10/100/1000Base-T Ethernet ports, four 1000Base-X SFP ports and one console

port on the front panel, and one AC power socket, one RPS port, and two 10 GE

interface module slots on the rear panel. Figure 11 shows the appearance of the

Switch 4800G 24-Port SFP.

Figure 10 Appearance of the Switch 4800G 24-Port SFP

Front Panel Figure 11 Front panel of the Switch 4800G 24-Port SFP

Rear Panel Figure 12 Rear panel of the Switch 4800G 24-Port SFP

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) Console port (3) 7-segment digital LED

(4) Mode button (5) Mode LED

(6) Power LED (7) RPS LED

(8) LED for extended module slot 1 (9) LED for extended module slot 2

(10) SFP port status LED

(1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5) (1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5)

(1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5) (1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5)

(1) (2) (3) (4) (5)

18 CHAPTER 1: PRODUCT OVERVIEW

Power Supply System The Switch 4800G 24-Port SFP can adopt AC power input, or DC power input, or

both to provide backup.

■ AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz or 63 Hz

Only the RPS recommended by 3Com can be used for the Switch 4800G

24-Port SFP. The -48 VDC power supply in the equipment room cannot be used

directly. Otherwise, the device may be damaged.

■ DC power input

Rated voltage range: -52 VDC to -55 VDC

Cooling System The Switch 4800G 24-Port SFP is equipped with six fans for heat dissipation.

LEDs The LEDs on the front panel of the Switch 4800G 24-Port SFP are the same as

those of the Switch 4800G PWR 24-Port. For details, see Table 5.

Switch 4800G 48-Port

Appearance The Switch 4800G 48-Port provides twenty-four 1000Base-X SFP ports, eight

auto-sensing 10/100/1000Base-T Ethernet ports, and one console port on the

front panel, and two AC or DC power sockets and two extended module slots on

the rear panel.

Figure 13 shows the appearance of the Switch 4800G 48-Port.

Figure 13 Appearance of the Switch 4800G 48-Port

(1) RPS port (2) AC power socket

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

Switch 4800G 48-Port 19

Front Panel Figure 14 Front panel of the Switch 4800G 48-Port

Rear Panel Figure 15 Rear panel of the Switch 4800G 48-Port

Power System The Switch 4800G 48-Port can adopt two hot-swappable AC or DC power

modules to provide backup.

■ AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

■ DC power input

Rated voltage range: -48 VDC to -60 VDC

Input voltage range: -36 VDC to -72 VDC

Cooling System The Switch 4800G 48-Port is equipped with six fans (four for the system, and one

for each power module) for heat dissipation.

LEDs For descriptions about LEDs, see Table 6. You can switch the Mode LED display

mode between speed and duplex by pressing the Mode button on the panel.

(1) 100/1000Base-X SFP port status LED (2) Auto-sensing 10/100/1000Base-T Ethernet

port status LEDs

(3) Console port (4) 7-segment digital LED

(5) System status LED (6) LED for power module slot 2

(7) LED for power module slot 1 (8) LED for extended module slot 1

(9) LED for extended module slot 2 (10) Mode LED

(11) Mode button

(1) (2) (3) (4) (5) (6) (7) (8)

(11) (10) (9)

(1) Grounding screw (2) Power module slot 1

(3) Power module slot 2 (4) Extended module slot 1

(5) Extended module slot 2

(1)

(2) (3) (4) (5)

(1)

(2) (3) (4) (5)

(1)

(2) (3) (4) (5)

(1)

(2) (3) (4) (5)

(1)

(2) (3) (4) (5)

(1)

(2) (3) (4) (5)

20 CHAPTER 1: PRODUCT OVERVIEW

Table 6 Description of LEDs on the front panel of the Switch 4800G 48-Port

LED Mark Status Description

Mode LED Mode Speed Solid green Rate of the port

Duplex Solid yellow Duplex of the port

System power LED SYS Solid green The switch is started normally.

Flashing green (1 Hz) The system is running a POST.

Solid red The system fails the POST or a power

failure occurs.

Flashing yellow (1 Hz) Some ports fail the POST or a port failure

occurs.

OFF The power is disconnected.

LED for power

module slot 1

PWR1 Solid green A power module is installed in the power

module slot and the output is normal.

Solid yellow A power module is installed in the power

module slot but no power is output.

OFF No power module is installed in the power

module slot or no power is input.

LED for power

module slot 2

PWR2 Solid green A power module is installed in the power

module slot and the output is normal.

Solid yellow A power module is installed in the power

module slot but no power is output.

OFF No power module is installed in the power

module slot or no power is input.

Module LED MOD Solid green The module is in position and works

normally.

Flashing yellow The switch does not support the module

or a module failure occurs.

OFF No module is installed.

Page is loading ...

3com 4800G PWR Getting Started Manual

This manual is also suitable for

3com 4800G PWR Getting Started Manual

Related papers

Other documents