Rockwell Automation Allen-Bradley Micro800 Quick start guide

Micro800 Controllers Starter Pack Quick Start

Catalog Numbers Bulletin 2080-LC20, 2080-LC30, 2080-LC50

Quick Start

Original Instructions

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and

operation of this equipment before you install, configure, operate, or maintain this product. Users are required to

familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,

and standards.

Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are

required to be carried out by suitably trained personnel in accordance with applicable code of practice.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may

be impaired.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from

the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or

liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or

software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,

Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Labels may also be on or inside the equipment to provide specific precautions.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous

environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property

damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous

voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may

reach dangerous temperatures.

ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to

potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL

Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).

3Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 3
Where to Start
Follow this path to learn how to use the Connected Components Workbench™ software with your Micro800™ controllers 
and PanelView™ 800 terminals.
Chapter 1
Study Guide Overview
Chapter 2
Hands On Content
Chapter 3
Create and Save a Connected 
Components Workbench Project
Chapter 4
Build and Download Project
Chapter 5
Connect the Input Simulator Board
Chapter 6
Monitor Your Micro800 Controller 
Chapter 7
How to Create Variables
Chapter 8
How to Implement an Instruction Block
Chapter 9
How to Add a Plug-in Module
Chapter 10
Learn About User-Defined Functions 
(UDF) and User-Defined Function Blocks 
(UDFB)
Chapter 11
Import and Export Project
Chapter 12
Quick Tips
Chapter 13
PanelView 800 HMI Design Using 
Connected Components Workbench
Chapter 14
Using HMI Tags
Chapter 15
Configure Micro800 Controller 
Ethernet Settings
Chapter 16
HMI Tag Editor
Chapter 17
HMI Screen
Chapter 18
Configure PanelView 800 Terminal 
Ethernet Settings
Chapter 19
Download HMI Application
Chapter 20
Test the HMI Application

4 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Where to Start

Notes:

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 5

Table of Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Preface

About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 1

Study Guide Overview

Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Start Connected Components Workbench Software . . . . . . . . . . . . . . . . 11

Connected Components Workbench Design Environment. . . . . . . . . . 12

Project Organizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Workspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 2

Hands On Content

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 3

Create and Save a Connected

Components Workbench

Project

Create a Connected Components Workbench Project . . . . . . . . . . . . . . 19

Save Your Connected Components Workbench Project. . . . . . . . . . . . . 25

Chapter 4

Build and Download Project

Build and Download the Project to your Micro800 Controller . . . . . . . 27

Chapter 5

Connect the Input Simulator

Board

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Chapter 6

Monitor Your Micro800

Controller Program

Monitor Your Program in

Connected Components Workbench Software . . . . . . . . . . . . . . . . . . . . . 33

View Real-time Changes in List Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Chapter 7

How to Create Variables

Create Local Variables for your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Chapter 8

How to Implement an

Instruction Block

Add a TON Instruction Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Enter Parameters for TON Instruction Block. . . . . . . . . . . . . . . . . . . . . . . 41

Add an ANY_TO_TIME Instruction Block . . . . . . . . . . . . . . . . . . . . . . . 44

6 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Table of Contents

Chapter 9

How to Add a Plug-in Module

Add a Plug-in Module to the Micro800 Controller. . . . . . . . . . . . . . . . . . 49

Chapter 10

Learn About User-Defined

Functions (UDF) and

User-Defined Function Blocks

(UDFB)

Create a UDF for your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Add the UDF to your Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Get Sample Code from the

Rockwell Automation Sample Code Library . . . . . . . . . . . . . . . . . . . . . . . . 59

Import Sample Code into Your Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Chapter 11

Import and Export Project

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Chapter 12

Quick Tips

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Chapter 13

PanelView 800 HMI Design

Using Connected Components

Workbench

Add a PanelView 800 Terminal to Your Project. . . . . . . . . . . . . . . . . . . . . 69

Configure Your PanelView 800 Terminal Communication Settings . . 70

Chapter 14

Using HMI Tags

Create Global Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Edit Ladder Diagram Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Chapter 15

Configure Micro800 Controller

Ethernet Settings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Chapter 16

HMI Tag Editor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

Chapter 17

HMI Screen

Create a Screen for Your PanelView 800 Application. . . . . . . . . . . . . . . . 83

Create Objects for Your Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Chapter 18

Configure PanelView 800

Terminal Ethernet Settings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Chapter 19

Download HMI Application

Save and Download Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 7

Table of Contents

Chapter 20

Test the HMI Application

Run the HMI Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Test the HMI application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Appendix A

Set Up Serial Communication

Between PC and Micro820

Controller

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Connect the PC to the Micro820 Controller . . . . . . . . . . . . . . . . . . . . . . 108

Configure RSLinx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Restore Serial Port to Factory Default Setting

Using MicroSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

8 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Table of Contents

Notes:

9 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 9

Preface

About This Publication

Use this quick start to learn how to use a Micro800 controller with a PanelView 800 terminal. You will use the Connected

Components Workbench software.

Additional Resources

These documents contain additional information concerning related products from Rockwell Automation.

You can view or download publications at

http:/www.rockwellautomation.com/literature/. To order paper copies of technical documentation, contact your local

Allen-Bradley distributor or Rockwell Automation sales representative.

Resource Description

Micro800 Controllers Starter Pack Quick Reference,

publication

2080-QR003

Provides information for setting up the Micro800 controllers and input simulator

boards.

PanelView 800 HMI Terminals User Manual, publication

2711R-UM001

Information in setting up and using the PanelView 800 terminals, and installing

the Connected Components Workbench software.

Micro820 20-point Programmable Controllers User

Manual, publication

2080-UM005

Information on setting up and using the Micro820™ controllers.

Micro830 and Micro 850 Programmable Controllers

User Manual, publication

2080-UM002

Information on setting up and using the Micro830

®

and Micro850

®

controllers.

Connected Components Workbench Software Website

http://www.rockwellautomation.com/global/support/c

onnected-components/workbench.page

Provides product information on Connected Components Workbench software

and links to download the software.

Connected Components Workbench Online Help Online Help that provides a description of the different elements of the

Connected Components Workbench software.

10 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Preface

Notes:

11Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 11

Chapter

1

Study Guide Overview

Objectives

This self study guide is intended for new users of Connected Components Workbench software who have purchased the

Micro820 or Micro850 Starter Pack. This document is also a useful self study guide to any new users of Micro800

controllers or PanelView 800 terminals who did not purchase the Micro820 or Micro850 Starter Pack. This self study

guide assumes that the user has basic knowledge of a Programmable Logic Controller (PLC).

The Micro850 controller is used in the examples shown in this quick start, however they also apply to Micro820

controllers. Any major differences between the Micro820 and Micro850 controllers will be mentioned.

Required Tools

• One of the following Micro800 Starter Packs:

– Micro820 Starter Pack Lite (2080-LC20-STARTERPACKL) or

– Micro820 Starter Pack with PanelView 800 (2080-LC20-STARTERPACK) or

– Micro850 Starter Pack Lite (2080-LC50-STARTERPACKL) or

– Micro850 Starter Pack with PanelView 800 (2080-LC50-STARTERPACK)

• Micro800 controller firmware revision 10.011 or later

• Connected Components Workbench software version 10.01 or later

Software can be downloaded from the Connected Components Workbench website

http://www.rockwellautomation.com/global/support/connected-components/workbench.page

Start Connected Components Workbench Software

To start the Connected Components Workbench (CCW) software, launch the

program from your Windows Start Menu by going to: Start -> All Programs ->

Rockwell Automation -> CCW -> Connected Components Workbench.

12 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Chapter 1 Study Guide Overview

Connected Components Workbench Design Environment

This is the default project layout. The contents of each window and the general task the window is used for are described

below.

Project Organizer

Project Organizer displays the contents of your project in an organized tree

view, providing access to each of the devices and project elements.

From the Project Organizer, you can add, move, or delete devices and project

elements, and double-click them to display their contents.

If your project contains a Micro800 controller, the Project Organizer also

displays the logic programs, variables, user-defined functions (UDF) and

user-defined function blocks (UDFB) that are associated with that controller.

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 13

Study Guide Overview Chapter 1

Workspace

The Start Page in the workspace provides a starting point for your work flow. It is categorized into three sections – Project,

Recent and Getting Started.

Under the Project section, you can click:

• New to create a new project

• Open Existing to browse for another project file not listed under Recent

• Discover to browse for a device such as a Micro800 controller using USB or Ethernet

The Recent section provide a list of project files that were opened recently. The Getting Started section provides links to

online content that will help you with developing applications in Connected Components Workbench software.

14 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Chapter 1 Study Guide Overview

Toolbox

The Toolbox is context sensitive to the device or

workspace being edited. The toolbox is used when

editing a Micro800 program and when editing a

PanelView 800 screen.

From the Toolbox, you can drag and drop Toolbox

elements, or copy and paste elements to another

window.

Output

In the Output window, you can view and manage general purpose and debug messages that are generated by the various

features of Connected Components Workbench software.

From the Output window, you can do the following:

•Review status messages

• Locate errors within programs

Toolbox for Micro800 Toolbox for PanelView 800

Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 15

Study Guide Overview Chapter 1

Status Bar

The Status bar shows the task that the Connected Components Workbench software is currently performing.

Connected Components Workbench software is building a project

Connected Components Workbench software has successfully download a project into a controller

16 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Chapter 1 Study Guide Overview

Notes:

17Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 17

Chapter

2

Hands On Content

Overview

The following chapters provide examples for you to learn how to create a project for your Micro800 controller and

PanelView 800 terminal in Connected Components Workbench software.

• Create a Connected Components Workbench project

• Save your Connected Components Workbench project

• Build and download your Micro800 controller application

• Connect the input simulator board to your Micro800 controller

• Monitor your Micro800 controller program

• Learn how to create variables

• Learn how to implement an Instruction Block

• Learn how to add a plug-in module

• Learn about User-Defined Functions and User-Defined Function Blocks

• Import/ Export Project (Connected Components Workbench version 8.00 or later)

• Add a PanelView 800 terminal to your Connected Components Workbench project

• Learn how to create HMI tags

• Configure your Micro800 controller Ethernet port

• Learn how to use the HMI tag editor

• Learn how to create screens for your HMI

• Configure your PanelView 800 terminal Ethernet settings

• Download the HMI application to your PanelView 800 terminal

• Test the HMI application

18 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Chapter 2 Hands On Content

Notes:

19Rockwell Automation Publication 2080-QS004B-EN-E - October 2017 19

Chapter

3

Create and Save a Connected Components Workbench Project

Create a Connected Components Workbench Project

To create a new project, do the following:

1. Click New on the Start Page.

Alternatively, go to File -> New or use the keyboard shortcut “Ctrl+N”.

2. Enter a name for your project and click Create.

Ensure that the Add Device on Create checkbox is selected. This will open an Add Device dialog box for you to add

a device to this project.

3. In the left pane, click the “+” sign to expand the list of catalogs and select the device to add into the Selection list.

By default, the latest major controller version is selected. Select the required version from the drop-down box.

20 Rockwell Automation Publication 2080-QS004B-EN-E - October 2017

Chapter 3 Create and Save a Connected Components Workbench Project

4. Click Add To Project to complete the device selection.

Add a Ladder Diagram program to your project

1. Right-click Programs under the Micro850 controller in your Project Organizer, and select

Add -> New LD : Ladder Diagram.

2. Observe that a new Ladder Diagram program called Prog1 has been added under Programs.

Micro800 controllers allow you to create multiple programs and use multiple types of programs (such as Structured

Text or Function Block Diagram) in the same controller application.

Page is loading ...

Rockwell Automation Allen-Bradley Micro800 Quick start guide

This manual is also suitable for

Rockwell Automation Allen-Bradley Micro800 Quick start guide

Related papers

Other documents