Altronix TROVE T2PXK78 User manual

Brand: Altronix

Model: TROVE T2PXK78

Type: User manual

This manual is also suitable for

TROVE T2PXK78, T2PXK78D 8 Door Access and Power Integration Kit

Altronix TROVE T2PXK78 is a pre-assembled kit that integrates power and access control for up to eight doors in a single enclosure. It includes an Altronix power supply/charger, fused access power controller, voltage regulator, and dual input fused power distribution module, along with the necessary hardware for mounting Paxton Net2 Plus modules. This kit is ideal for small to medium-sized access control systems and provides reliable power and protection for your access control devices.

T2PXK78

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with TPX2 Altronix/Paxton backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) ACM8 - Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

T2PXK78D

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TPX2 Altronix/Paxton backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) ACM8CB - PTC Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

Access & Power Integration

Altronix/Paxton Kits

Models Include:

Rev. TPXLK_122821

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

- 2 - Trove PX ULXB Kits Installation Guide

Overview:

Altronix Trove Paxton kits are pre-assembled and consist of Trove2PX2 enclosure/backplane with factory installed Altronix power supply/charger

and sub-assemblies. They also accommodate up to eight (8) Paxton Net2 Plus modules for up to eight (8) doors in a single enclosure.

Configuration Chart:

Altronix

Model

Number

115VAC

60Hz

Input

Current

(A)

Power

Supply

Board

Input

Fuse

Rating

Power

Supply

Board

Battery

Fuse

Rating

Maximum Supply

Current for Main

Output on Power

Supply board and

ACM8(CB) Access

Power Controller’s

outputs

Nominal

Output

Voltage

Class 2 Rated Power-

Limited Outputs

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Additional Fuse or PTC

Protected Outputs

ACM8(CB) Board

Input Fuse Rating

ACM8 Board

Output Fuse Rating

ACM8CB Board

Output PTC Rating

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

PDS8CB Board

Input PTC Rating

PDS8CB Board

Output PTC Rating

Output

Range

(VDC)

T2PXK78

4.2 5A/

250V

15A/

32V 24VDC @ 9.7A 20.17-

26.4

– 8 8 10A/

250V

2.5A/

250V –10A/

32V

3A/

32V – –

T2PXK78D P8 8 10A/

250V – 2.5A – – 9A 2.5A

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners

and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper

screws; level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and

install the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the three lower

screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent)

in desired location, opposite hinge. Slide the tamper switch bracket onto the edge

of the enclosure, approximately 2” from the right side (Fig. 1, pg. 2).

Connect tamper switch wiring to the Access Control Panel input or the appropriate

UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount Paxton Net2 Plus modules to TPX2 backplane, refer to page 3.

5. Refer to the ULXB Power Supply/Charger Installation Guide for AL1024ULXB2 and

corresponding Sub-Assembly Installation Guides for the following models:

ACM8(CB), PDS8(CB) and VR6 for further installation instructions.

Hardware:

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Nylon Spacer | 5/16” Pan Head Screw | Lock Nut

Trove PX ULXB Kits Installation Guide - 3 -

Altronix

AL1024ULXB2

OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8

NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM

IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND

1 2 3 4 5 6 7 8

INPUT

TRIGGER

10A 250V

+INP- T + RET-

NO C NC

FACP INTERFACE

Power Control

- + - +

MAIN

TRG

FACP

1 2 3 4

+ INP1 --

DM1 +OFF

IN1

IN2DM1 +

DM2 +

Common (--- )

+ INP2 --

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix PDS8(CB)

Altronix VR6 is mounted under PDS8(CB)

Altronix

ACM8(CB)

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Switch Switch

Paxton Net2 Plus Paxton Net2 Plus

Switch Switch

Paxton Net2 Plus Paxton Net2 Plus

Switch Switch

Paxton Net2 Plus Paxton Net2 Plus

Switch Switch

Paxton Net2 Plus Paxton Net2 Plus

RJ45 Jack

Configuration of Paxton Net2 Plus Modules:

1. Align the Paxton Net2 Plus modules on the backplane to match the modules’ mounting holes with corresponding pems.

2. Fasten spacers (provided) onto metal pems (Fig. 2a, pg. 3).

3. Mount Paxton Net2 Plus modules to spacers utilizing pan head screws (provided) (Fig. 2a, pg. 3).

Note: Paxton Net2 Plus modules have one (1) RJ45 jack and one (1) switch each.

Please make sure that they are mounted correctly, as shown in Fig. 2 below.

4. Fasten TPX2 backplane to Trove2 enclosure utilizing hardware (provided).

Fig. 2

Pem

Spacer

Paxton

Net2 Plus Backplane

Pan Head

Screw

Fig. 2a

- 4 - Trove PX ULXB Kits Installation Guide

Enclosure Dimensions (H x W x D approximate):

27.25” x 21.5” x 6.5” (692.15mm x 546.1mm x 165.1mm)

6.75” (171.5mm)8.25” (209.5mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

1.25” (31.8mm)

6.25” (158.8mm) 19.80” (502.9mm)

1.00” (25.4mm)

27” (685.8mm)

1.5”

(38.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

3.5”(88.9mm) 3.5”(88.9mm)

21.50” (546.1mm)

5.25” (133.35mm) 5.25” (133.35mm)

6.25” (158.8mm)

1.25”

(31.8mm)

0.85” (21.6mm)

0.5625” (14.3mm)

2.415” (61.3mm)

0.685” (17.4mm)

1.77”

(45mm)

0.885” (22.5mm)

1.125” (28.3mm)

Knockouts

2.00” (50.8mm) 2.00” (50.8mm)

Altronix is not responsible for any typographical errors.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IITrove PX ULXB Kits L28U

MEMBER