Altronix T2SK78D Installation guide

Type
Installation guide

Altronix T2SK78D is an 8 Door Kit with PTC Outputs that includes an enclosure with a backplane, power supply/chargers, access power controller, voltage regulator, and power distribution modules. This kit is designed for access control systems and can accommodate various combinations of Software House boards for up to 8 doors in a single enclosure. It features PTC protected outputs for added safety and reliability. The kit includes all the necessary components for a complete access control solution.

Altronix T2SK78D is an 8 Door Kit with PTC Outputs that includes an enclosure with a backplane, power supply/chargers, access power controller, voltage regulator, and power distribution modules. This kit is designed for access control systems and can accommodate various combinations of Software House boards for up to 8 doors in a single enclosure. It features PTC protected outputs for added safety and reliability. The kit includes all the necessary components for a complete access control solution.

T2SK78D
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with
TSH2 Altronix/Software House backplane
- One (1) AL1024ULXB2 - Power Supply/Charger
- One (1) ACM8CB - PTC Protected Access Power Controller
- One (1) VR6 - Voltage Regulator
- One (1) PDS8CB - Dual Input Power Distribution Module
- One (1) Rocker Switch Bracket with One (1) Rocker Switch
(Not evaluated by UL)
T3SK758D
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove3 enclosure with
TSH3 Altronix/Software House backplane
- One (1) AL1024ULXB2 - Power Supply/Charger
- One (1) AL1012ULXB - Power Supply/Charger
- One (1) ACM8CB - PTC Protected Access Power Controller
- One (1) PD8ULCB - PTC Protected Power Distribution Module
- One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)
T3SK7516D
16 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove3 enclosure with
TSH3 Altronix/Software House backplane
- One (1) AL1024ULXB2 - Power Supply/Charger
- One (1) AL1012ULXB - Power Supply/Charger
- Two (2) ACM8CB - PTC Protected Access Power Controllers
- One (1) PD8ULCB - PTC Protected Power Distribution Module
- One (1) Rocker Switch Bracket with Two (2) Rocker Switches
(Not evaluated by UL)
Access & Power Integration
Altronix/Software House Kits
Models Include:
Rev. TSKLD120321
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
- 2 - Trove Software House ULXB PTC Kits Installation Guide
Overview:
Altronix Trove Software House kits are pre-assembled and consist of Trove enclosure with factory installed Altronix power supply/chargers and
sub-assemblies. These kits also accommodate various combinations of Software House boards for up to sixteen (16) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
120VAC 60Hz Input Current
(A)
Power Supply Board
Input Fuse Rating
Power Supply Board Battery
Fuse Rating
Nominal DC Output Voltage Options Maximum
Supply Current
for Main and
Aux. Outputs
on Power Supply
board and
ACM8CB
Access Power
Controller’s
outputs (A)
Fail-Safe/
Fail-Secure Outputs
Current Per
ACM8CB Output (A)
ACM8CB Board
Input Fuse Rating
ACM8CB Board
Output PTC Rating
PDS8CB Board
Input PTC Rating
PDS8CB Board
Output PTC Rating
PD8ULCB Board
Output PTC Rating
Power Supply 1 Power Supply 2
[DC] [AUX] [DC] [AUX]
12VDC Output
Range (V)
24VDC Output
Range (V)
12VDC Output
Range (V)
24VDC Output
Range (V)
12VDC Output
Range (V)
24VDC Output
Range (V)
12VDC Output
Range (V)
24VDC Output
Range (V)
T2SK78D 4.5 5A/250V 15A/
32V
AL1024ULXB2 N/A
24VDC @ 9.2A 8 2.0 10A/
250V 2A 9A 2A
20.17-
26.4 20.17-
26.4
T3SK758D 8.0 5A/250V 15A/
32V
AL1024ULXB2 AL1012ULXB
24VDC @ 9.2A 8 2.0 10A/
250V 2A – – 2A
20.19-
26.4 20.19-
26.4
10.0-
13.2 10.03-
13.2
T3SK7516D 8.0 5A/250V 15A/
32V
AL1024ULXB2 AL1012ULXB
24VDC @ 9.2A 16 2.0 10A/
250V 2A – – 2A
20.19-
26.4 20.19-
26.4
10.0-
13.2 10.03-
13.2
Hardware and Accessories:
Nylon spacers - eighteen (18) for T2SK78D, forty-six (46) for T3SK758D or T3SK7516D.
5/16” pan head screws - eighteen (18) for T2SK78D, forty-six (46) for T3SK758D or T3SK7516D.
Tamper switch (Altronix Model TS112 or equivalent) - one (1) for T2SK78D, two (2) for T3SK758D or T3SK7516D.
Cam lock.
Battery leads.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install
the three fasteners. Place the enclosure’s upper keyholes over the three upper screws.
Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location,
opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2”
from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or
the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.
4. Mount Software House boards to backplane, refer to pages 3-8.
5. Refer to the ULXB Power Supply/Charger Installation Guide for AL1012ULXB and AL1024ULXB2
and corresponding Sub-Assembly Installation Guides for the following models: PD8ULCB, ACM8(CB),
PDS8(CB), VR6 for further installation instructions.
Metal or Nylon Spacer | 5/16” Pan Head Screw | Lock Nut
Fig. 1
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure
Trove Software House ULXB PTC Kits Installation Guide - 3 -
T2SK78D: Configuration of Software House iSTAR Ultra Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten spacers (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and /or I8, R8, I8-CSI
boards (Fig. 2, 2a, pg. 3).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 2a, pg. 3).
Note: Software House iSTAR Ultra ACM boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 2 below.
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 2
Software House
I8, R8 or I8-CSI Module
Software House
iSTAR Ultra GCM
Software House
iSTAR Ultra ACM SE
USB PORT
RJ45 Jack
RSB1
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
+ INP1 --
PWR1 +OFF
IN1
IN2
Out1
<1 off 2>
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
Altronix VR6 is mounted under PDS8CB
Altronix - PDS8CB
Software House
iStar Ultra ACM
L
G
N
BAT FAIL
AC FAIL
NC
C
NO
NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 2a
- 4 - Trove Software House ULXB PTC Kits Installation Guide
T2SK78D: Configuration of Software House iSTAR Pro Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten provided spacers to pems that match the hole pattern for Software House iSTAR Pro GCM, iSTAR ACM SE/PRO ACM, and /or I8,
R8, I8-CSI boards (Fig. 3, 3a, pg. 4).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 3a, pg. 4).
Note: Software House iSTAR ACM SE/PRO ACM boards have one (1) USB port each.
Please orient boards in the appropriate position according to the Fig. 3 below.
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 3
Software House
iSTAR Pro GCM
Software House
iSTAR Pro ACM
USB PORT
Software House
I8, R8 or
I8-CSI
Module
RSB1
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
+ INP1 --
PWR1 +OFF
IN1
IN2
Out1
<1 off 2>
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
Altronix VR6 is mounted under PDS8CB
Altronix - PDS8CB
L
G
N
BAT FAIL
AC FAIL
NC
C
NO
NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 3a
Trove Software House ULXB PTC Kits Installation Guide - 5 -
T3SK758D or T3SK7516D: Configuration of Software House iSTAR Ultra Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided.
2. Fasten spacers (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and /or I8, R8, I8-CSI
boards (Fig. 4, 4a, pg. 5).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 4a, pg. 5).
Note: Software House iSTAR Ultra ACM boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 4 below.
4. Fasten backplane to Trove3 enclosure utilizing lock nuts (provided).
Fig. 4
Software House
iSTAR Ultra GCM
Software House
iSTAR Ultra ACM
Software House
iSTAR Ultra ACM
Software House
I8, R8 or I8-CSI Module
Software House
I8, R8 or I8-CSI Module
Software House
iSTAR Ultra ACM SE
USB PORT
Software House
iSTAR Ultra ACM SE
USB PORT
RJ45 Jack
RJ45 Jack
Altronix - PD8ULCB
(T3SK7516D)
Altronix - PD8ULCB
(T3SK758D)
RSB2
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
Power Control
- + - +
INPUT
COMMON POWER OUTPUTS N P
N
P
FUSED POWER OUTPUTS
N P
Altronix
ACM8CB
(T3SK7516D)
Dashed Line indicates pre-wired kit for T3SK7516D
Dashed Line indicates pre-wired kit for T3SK758D
L
G
N
BAT FAIL
AC FAIL
NC
C
NO
NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
+ BAT -
L G N BAT FAIL NC C NO NC C NO AC FAIL
AC DC
- DC +
Altronix - AL1012ULXB
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 4a
- 6 - Trove Software House ULXB PTC Kits Installation Guide
T3SK758D or T3SK75FD: Configuration of Software House iSTAR Pro Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided.
2. Fasten provided spacers to pems that match the hole pattern for Software House iSTAR Pro GCM, iSTAR ACM SE/PRO ACM, and /or I8,
R8, I8-CSI boards (Fig. 5, 5a, pg. 6).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 5a, pg. 6).
Note: Software House iSTAR ACM SE/PRO ACM boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 5 below.
4. Fasten backplane to Trove3 enclosure utilizing lock nuts (provided).
Fig. 5
Software House
I8, R8 or I8-CSI Module
Software House
iSTAR Pro GCM
USB PORT Software House
iSTAR Pro ACM
USB PORT Software House
iSTAR Pro ACM
Software House
I8, R8 or I8-CSI Module
RSB2
Altronix - PD8ULCB
(T3SK7516D)
Altronix - PD8ULCB
(T3SK758D)
RSB2
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
Power Control
- + - +
INPUT
COMMON POWER OUTPUTS N P
N
P
FUSED POWER OUTPUTS
N P
Altronix
ACM8CB
(T3SK7516D)
Dashed Line indicates pre-wired kit for T3SK7516D
Dashed Line indicates pre-wired kit for T3SK758D
L
G
N
BAT FAIL
AC FAIL
NC
C
NO
NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
+ BAT -
L G N BAT FAIL NC C NO NC C NO AC FAIL
AC DC
- DC +
Altronix - AL1012ULXB
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 5a
Trove Software House ULXB PTC Kits Installation Guide - 7 -
T2SK78D Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
6.75” (171.5mm)8.25” (209.5mm)
8.00” (203.2mm)
2.00” (50.8mm)
2.00” (50.8mm)
1.25” (31.8mm)
1.25” (31.8mm)
5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)
1.25” (31.8mm)
6.25” (158.8mm) 19.80” (502.9mm)
1.00” (25.4mm)
27” (685.8mm)
1.5”
(38.1mm)
2.00” (50.8mm) 2.00” (50.8mm)
3.5”(88.9mm) 3.5”(88.9mm)
21.50” (546.1mm)
5.25” (133.35mm) 5.25” (133.35mm)
6.25” (158.8mm)
1.25”
(31.8mm)
0.85” (21.6mm)
0.5625” (14.3mm)
2.415” (61.3mm)
0.685” (17.4mm)
1.77”
(45mm)
0.885” (22.5mm)
1.125” (28.3mm)
Knockouts
2.00” (50.8mm) 2.00” (50.8mm)
- 8 - Trove Software House ULXB PTC Kits Installation Guide
T3SK758D and T3SK7516D Enclosure Dimensions (H x W x D approximate):
36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)
G
G
2”
(50.8mm)
8.75” (222.3mm) 8.75” (222.3mm)
8.62” (219mm)
7.06” (179.3mm)
1.25” (31.8mm)
1.25” (31.8mm)
2.00” (50.8mm) 7.12” (222.3mm) 9.5” (241.3mm) 9.5” (241.3mm)
30.12” (768.1mm)
14.01” (355.9mm) 14.01” (355.9mm)
1.25” (31.8mm) 1.55” (39.4mm)
1.78” (45.2mm)
1.25” (31.8mm)
1.07”
(27.2mm)
1.10” (27.9mm)
2” (50.8mm)
10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
2.00” (50.8mm)10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
36.12” (917.5mm)
33.63” (854.2mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IITroveSH ULXB Kit D Series L03U MEMBER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Altronix T2SK78D Installation guide

Type
Installation guide

Altronix T2SK78D is an 8 Door Kit with PTC Outputs that includes an enclosure with a backplane, power supply/chargers, access power controller, voltage regulator, and power distribution modules. This kit is designed for access control systems and can accommodate various combinations of Software House boards for up to 8 doors in a single enclosure. It features PTC protected outputs for added safety and reliability. The kit includes all the necessary components for a complete access control solution.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI